KickerメーカーKX200.4の使用説明書/サービス説明書
ページ先へ移動 of 20
KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 January 1, 2004 KX1 00.2 & KX200.4 T ech- nical Manual.
Features KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 Page 2 R adically Adv anced Chassis with removable shroud and impr oved heatsink technology . The heatsinks provide the amplifier with longer runtime, improved r eliability and performance.
Custom tooled gold plated connectors Assure maximum power transfer and damping. SAMS ( S ter eo A nd M ono S imultaneously) Amplifier will operate into a bridged mono load and a stereo load at the same time. This type of system is great if the consumer is just starting out, or on a tight budget.
When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that there are no items behind the ar ea that could be damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc. All amplifiers generate heat under normal opera- tion.
SOURCE UNIT WA R NING-Use Only One... Never Both At The Same T ime!!! Speaker Outputs RCA Outputs LEFT + LEFT - RIGHT - RIGHT + High-Level Inputs KX1 00.
SOURCE UNIT WA R NING-Use Only One... Never Both At The Same T ime!!! Speaker Outputs RCA Outputs LEFT + LEFT - RIGHT - RIGHT + AMP 1 AMP 2 High-Level Inputs LEFT + LEFT - RIGHT - RIGHT + KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 Page 6 KX200 .
Wiring Instructions SOURCE UNIT Speaker Outputs RCA Dummy Plugs LEFT + LEFT + LEFT - RIGHT - RIGHT + AMP 1 AMP 2 High-Level Inputs LEFT - RIGHT - RIGHT + When using both sets of High L ev el inputs , the supplied RCA dumm y plugs must b e inserted into the AMP 2 inputs in order for the fa der to work properly .
Wiring cont. The use of twisted pair interconnects is recommended for all installations to minimize noise. When r outing these cables through the automobile, try to keep them away from factory wiring har nesses and other power wiring. If you need to cross any of this wiring do so at a 90 degree angle to r educe the possibility for noise problems.
A djusting Amplifier Controls On your Kicker amplifier there are r otary controls and switches on the end panel. These controls ensure the relia- bility and performance of the amplifier , so they need to be set correctly . If you are using a KX150.4 you will have two sets of rotary controls and switches.
Crosso v er Control Where you set the crossover is very subjective and can be fine tuned to match your listening pr eference or speaker requirement. If the amplifier is driving small speakers (cr ossover set to HI P ASS) this will eliminate the low frequencies from damaging the high fr equency speaker .
GROUND REMOTE TURN-ON BA T TER Y +12V FUSE RIGHT SPEAKER(S) LEFT SPEAKER(S) + _ + _ 18" or less 2 Ω Min. 2 Ω Min. SIGNAL IN When the amplifier is driving speaker s that do not require a crosso ve r , the crosso ver switch may b e set to the OFF position.
GROUND REMOTE TURN-ON BA T TER Y +12V FUSE 18" or less + _ MONO SPEAKER 4 Ω Min. SIGNAL IN If the amplifier is used to drive sub woofers , set the switch to LO P ASS. This will allow only low fr equencies to pass through the amplifier to the woofer s.
GROUND REMOTE TURN-ON BA T TER Y +12V FUSE RIGHT SPEAKER(S) LEFT SPEAKER(S) + _ + _ 18" or less + _ MONO SPEAKER HIGH PASS CROSSOVER LOW PAS S CROSS- OVE R HIGH P ASS CROSSOVER 4 Ω Min. 2 Ω Min. 2 Ω Min. SIGNAL IN When the amplifier is driving speakers in the configur ation abo ve, the crosso ver switch should be set to the OFF position.
When AMP 1 or AMP 2 are driving speak ers that do not require a crosso ve r , the crosso ver switch may b e set to the OFF position. This will allow the speaker s to play full range . OR... If AMP 1 or AMP 2 are driving speak ers that do require a crosso ve r set the switch to HI P ASS.
+ - GROUND REMOTE TURN-ON BA T TER Y +12V FUSE 18" or less + - + - SIGNAL IN AMP 1 SIGNAL IN AMP 2 When AMP 1 is driving speaker s that do not require a crosso ver , the crosso ver switch may b e set to the OFF position. This will allow the speaker s to play full range .
+ - + - GROUND REMOTE TURN-ON BA T TERY +12V FUSE 18" or less If AMP 1 or AMP 2 are used to drive sub woof er s, set the switch to L O PASS. This will allow only low fr equencies to pass through the amplifier to the woofer s. MAKE SURE: * The LEFT input must be split up an d fed to the L & R Amp 1 inputs with a Y-A dapter .
Formulas KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 Page 17 Ohm’s La w E = I X R Wher e: E = V oltage (V olts) I = Curr ent (Amps or Amper es) R = R esistance (Ohms or W W ) F ormula V ar.
(T otal RMS power output into 4 W W ) x 2 = (T otal input wattage [W atts]) (T otal input wattage) = (Maximum input current [Amps]) (Supply V oltage) Example: Amplifier with a r ating of 1 00 watts per channel into 4 W W 200 x 2 = 400 W atts (T otal input po wer) 400 W atts / 12.
• Damage due to improper installation. • Subsequent damage to other components. • Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation. • Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be consider ed abuse.
P .O . Box 459 – Stillw ater , Oklahoma 74076 – U.S.A. – 405 624-85 1 0 or www .Kick er .com.
デバイスKicker KX200.4の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kicker KX200.4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKicker KX200.4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kicker KX200.4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kicker KX200.4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kicker KX200.4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKicker KX200.4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kicker KX200.4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKicker KX200.4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
