LevelOneメーカーIFE-0500の使用説明書/サービス説明書
ページ先へ移動 of 21
LevelOne IFE-0500 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch User Manual V er . 1.0.0-071 1 1.
FCC W arning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of t he FCC rules. These limits are designed to provide reasonable protection against harmful in terference in a residential installation.
Content INTRODUCTION ...................................................................................... 4 F EA TURES ................................................................................................................. 4 P ACKAGE C ONTENTS .
Introduction The 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch is a cost-effective solution and meets the high reliability requirement s demanded by indus trial applications. In addition, the industrial switch provides the PoE function for kinds of Powered Devices to receive power as well as data over the RJ-45 cable.
Package Content s Please refer to the package content s list below to verify them against the checklist. IFE-0500 CD Manual Pluggable T erminal Block (att ached on the switch) 2 wall mount plates with screws One DIN-Rail (attached on the switch) Compare the content s of the i ndustrial switch with the standar d checklist above.
Hardware Description In this paragraph, the Industrial switch’ s hardware spec, port, cabling information, and wiring installation will be described.
T op V iew The top view of the 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch has one terminal block connector of two DC power inputs. T op V iew of the IFE-0500 Indus trial Fast Ethernet Swit.
LED Indicators The diagnostic LEDs located on the front pa nel of the industrial switch provide real-time information of system and optional status. The following t able provides the description of the LED status and their meanings for the switch.
Port s RJ-45 ports The UTP (RJ-45) Fast Ether net port s will auto-sense for 10Base-T or 100Base-TX connections. Auto MDI/MDIX me ans that the switch can connect to another switch or workstation without changing straight thr ough or crossover cabling.
S traight Through Cable Schematic Cross Over Cable Schematic 10.
Cabling T wisted-pair segment c an be connected with unshielded twisted p air (UTP) or shielded twisted pair (STP) cable. The cable must comply with the IEEE 802.3u 100Base TX st andard for Category 5. The cable between the converter and the link partner (switch, hub, workst ation, et c.
Wiring the Power Input s Please follow the steps below to insert the power wire. Insert the positive and negative wires into t he V+ and V - contacts on the terminal block connector . T ighten the wire-clamp scr ews for preventing the wires from loosing.
Wiring the Fault Alarm Cont act The fault alarm contact is in the middle of terminal block connector as the picture shows below . When the wires are inserted in to ports 3 and 4, t hey automatically detect the fault status in the event of a power failure by forming an open circuit.
Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the i ndustrial switch when out of factory . If the DIN-Rail is not screwed on the industrial switch, please see the following pictures to screw the DIN-Rail on the switch. Follow the step s below to hang the industrial switch.
4. Then, lightly push the DI N-Rail into the track. 5. Check if the DIN-Rail is tightened on the track or not. 6. T o remove the industrial switch from the track, reverse steps above.
W all Mount Plate Mounting 1. Follow the steps below to mount the industrial switch wit h wall mount plate. 2. Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-Rail. 3. Place the wall mount plate on the rear panel of the industrial switch.
Hardware Installation In this paragraph, we are going to mention how to install the 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch and the installation point s to be attended to it. Inst allation Step s 1. Unpack the Industrial switch p acking.
Network Application This segment provides the sample to help user have more actual idea of industrial switch application. For a sample applicati on of the industrial s witch, see the figure below .
Troubleshooting V erify that is using the right power cord/adapter (DC 48V), please don’t use the power adapter with DC output voltage hi gher than 48V , or it will burn this equipment down. Select the proper UTP/STP cable to constr uct your network.
Technical Specification The IFE-0500 4-Port PoE + 1-Port TP Indus trial Fast Ethernet Switch technical specifications is shown as below . IFE-0500 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch Standard IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE802.
Power Consumption 3.4W att s (without PoE); 57 W a tts (Full load with PoE) Inst allation DIN rail kit for DIN-type cabinet install and wall-mount ear for wall mounting Operating T emp.
デバイスLevelOne IFE-0500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
LevelOne IFE-0500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLevelOne IFE-0500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LevelOne IFE-0500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LevelOne IFE-0500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LevelOne IFE-0500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLevelOne IFE-0500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LevelOne IFE-0500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLevelOne IFE-0500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。