Miller Electricメーカー3545の使用説明書/サービス説明書
ページ先へ移動 of 28
Processes OM-1216 205 917D 2006 − 09 Description MIG (GMAW) W elding Wire Feeder Spool Gun Spoolmat e 303 5 And 3545 Spoolma te 303 5 Spoolma te 354 5 ™ File: Wire Feeder V isit our website at www.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
OM-1216 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y W arning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown i n the adjoining symbols.
OM-1216 Page 2 Arc rays from the w elding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.
OM-1216 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-1216 Page 4 1-5. Principal Safety Standards Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www .
OM-1216 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION som _3/05 Y A vertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
OM-1216 Page 6 Le rayonnement de l’arc du procédé de soudage génère des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provo- quer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées pendant le soudage.
OM-1216 Page 7 2-3 . Da ngers supplém entair es en relation avec l’installa tion, le f onc tionneme nt et l a maintena nce Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur , au-dessus ou à proximité de surfaces inflammables.
OM-1216 Page 8 2-5. Princi pales nor mes de sécurit é Safety in W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www .
OM-1216 Page 9 SECTION 3 − INST ALLA TION 3-1. Specifications For Spoolmate 3035 Wire Diameter Range Approximate Wire Feed Range Cooling Method Maximum Spool Size W eld Circuit Rating Overall Dimensions W eight .023 Thru .035 in (0.8 Thru 0.9 mm) Aluminum Wire .
OM-1216 Page 10 3-3. Connecting Spool Gun T o Millermatic 210 3 802 998-C 1 2 4 Rear Panel 5 6 1 Barbed Fitting . If spool gun gas hose is equipped with a pre-installed barbed fitting, cut off fitting from end of hose. Connect spool gun gas hose to barbed fitting.
OM-1216 Page 1 1 3-4. Installing Wire Spool And Threading W elding Wire Ref. 801 891-B T ools Needed: 1 Thumb Screw 2 Spool Cover Remove thumb screw and spool cover . 3 Hub T ension Nut 4 Wire Spool Install spool so wire feeds from top. Turn hub tension nut just so a slight drag is felt on the wire spool.
OM-1216 Page 12 3-5. Removing Existing Barrel And Installing Contact Adapter 802 379-B 1 Base Nut Location Remove base nut from handle. 2 Handle Section Remove handle section from gun. 3 Drive Roll Assemblies Remove drive roll assemblies. 4 Nut Remove nut from barrel.
OM-1216 Page 13 SECTION 4 − OPERA TION 4-1. Controls sb5.1* 6/92 − S-0621-C / 804 386-A . Spool Gun On/Off switch in Millermatic 185 Hobart IronMan 210 or IronMan 250 must b e i n O n position for spool gun operation (see Field Kit 207 642 instructions).
OM-1216 Page 14 5-2. Changing Drive Rolls 801 893-B T ools Needed: Y T urn Off power at welding power source first. 1 Drive Roll Cover Remove cover . Changing Push Roll: T o remove push roll: 2 Push Roll Screw 3 W asher 4 Push Roll Remove screw and washer , and lift out drive roll.
OM-1216 Page 15 5-3. Changing Liner Ref. 801 891-B T ools Needed: Y T urn Off power at welding power source first. 1 Nozzle 2 Contact Tip 3 Liner Remove and replace liner . Reinstall parts as shown. 1 2 3 5-4. T roubleshooting T rouble Remedy Gun tube assembly loose.
OM-1214 Page 16 Notes.
OM-1216 Page 17 SECTION 6 − ELECTRICAL DIAGRAMS Figure 6-1. Circuit Diagram 186 451.
OM-1216 Page 18 SECTION 7 − P ARTS LIST . Hardware is common and not available unless listed. 801 900-F 3 2 32 28 31 33 29 19 30 18 17 27 22 21 20 14 11 10 4 9 8 7 6 5 4 2 1 40 41 42 43 39 38 36 37 35 34 23 26 25 24 13 15 16 12 Figure 7-1.
OM-1216 Page 19 Quantity Description Part No. Dia. Mkgs. Item No. Figure 7-1. Complete Assembly for Spoolmate 3035 1 PB1 186 416 TRIGGER SWITCH 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1216 Page 20 . Hardware is common and not available unless listed. 802 577-C 3 2 32 36 28 31 33 37 34 41 42 43 29 19 35 38 39 40 30 26 25 27 22 21 20 11 10 4 9 8 7 6 5 4 23 24 14 13 15 16 12 18 17 2 1 Figure 7-2.
OM-1216 Page 21 Quantity Description Part No. Dia. Mkgs. Item No. Figure 7-2. Complete Assembly For Spoolmate 3545 1 PB1 186 416 TRIGGER SWITCH 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1216 Page 22 204 161 1 2 3 4 5 6 Figure 7-3. Spoolmate Optional Hose & Cables Extension Kit Description Part No. 194 996 Item No. Figure 7-3. Spoolmate Hose & Cables Extension Kit Quantity 1 172 171 FITTING, hose, brass 1 . . . . . . . . . .
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 2006 − 01 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours.
PRINTED IN USA © 2006 Miller Electric Mfg. Co. 2006 − 01 Miller Elect ric Mfg. Co. An Illinois T ool W orks Compan y 1635 West Spenc er St reet Applet on, W I 54914 USA International He adquarters .
デバイスMiller Electric 3545の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Miller Electric 3545をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiller Electric 3545の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miller Electric 3545の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miller Electric 3545で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miller Electric 3545を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiller Electric 3545の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miller Electric 3545に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiller Electric 3545デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。