Miller ElectricメーカーOM-225Aの使用説明書/サービス説明書
ページ先へ移動 of 28
Processes Description Air Plasma Cutting and Gouging Air Plasma Cutter OM-225A February 1998 Eff. w/Serial Number KG155768 Spectrum 650 Cut F orc e R Visit our website at www.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
OM-225 Page 1 SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING pom _nd_5/97 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message.
OM-225 Page 2 Sparks and hot metal blow out from the cutting arc. Chipping and grinding cause flying metal. FL YING SP ARKS can cause injury . D W ear approved face shield or safety goggles with side shields. D W ear proper body protection to protect skin.
OM-225 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance HOT P ARTS can cause severe burns. D Do not touch hot parts bare handed. D Allow cooling period before working on torch. MOVING P ARTS can cause injury . D Keep away from moving parts such as fans.
OM-225 Page 4 1-5. EMF Information Considerations About Welding Or Cutting And The Ef fects Of Low Frequency Electric And Magnetic Fields W elding or cutting current, as it flows through the welding or cutting cables, will cause electromagnetic fields.
OM-225 Page 5 SECTION 1 – CONSIGNES DE S É CURIT É – LIRE A V ANT UTILISA TION pom_nd_fre_5/97 1-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette proc é dure pr é sente des risques de danger ! Ceux-ci sont identifi é s par des symboles adjacents aux directives.
OM-225 Page 6 D N ’ approchez pas le tube du chalumeau et l ’ arc pilote lorsque la g â chette est enfonc é e. D Le c â ble de masse doit ê tre pinc é correctement sur la pi è ce à couper ,.
OM-225 Page 7 1-3. Dangers suppl é mentaires en relation avec l ’ installation, le fonctionnement et la maintenance DES PIECES CHAUDES peuvent pro- voquer des br û lures graves. D Ne pas toucher des parties chaudes à mains nues. D Laisser refroidir avant d ’ intervenir sur la torche.
OM-225 Page 8 1-5. Information sur les champs é lectromagn é tiques Donn é es sur le soudage é lectrique et sur les ef fets, pour l ’ organisme, des champs magn é tiques basse fr é quence Le courant de soudage ou de coupage passant dans les c â bles de puis- sance c r é e des causera des champs é lectromagn é tiques.
OM-225 Page 9 SECTION 2 – INST ALLA TION 2-1. Specifications Input Power Rated Output Amperes Input at Rated Load Output T ype of Output Plasma Gas Plasma Gas Flow/ Rated Cutting Maximum Open- Circuit Power 230 V 460 V KV A KW Output Gas Pressure Capacity V oltage DC Single- Phase 50 A @ 1 1 0 V olts DC, 50% Duty Cycle 48 (0.
OM-225 Page 10 2-3. Cutting Speed The cutting speed curves show the recommended maximum cutting speed capabilities of the power source and torch for mild steel of various thickness. Cut at speeds below the lines shown t o avoid poor cuts and torch wear .
OM-225 Page 1 1 19 in (483 mm) 2-4. Selecting A Location Ref. ST-801 390 / ST -801 393 1 Lifting Handles Use handles to lift unit. 2 Hand Cart Use cart or similar device to move unit. 3 Rating Label Use rating label to determine input power needs. 4 Line Disconnect Device Locate unit near correct input power supply .
OM-225 Page 12 2-5. Connecting Work Clamp And Gas/Air Supply 1 Work Clamp 2 W orkpiece Connect work clamp to a clean, paint-free location on workpiece, as close to cutting area as possible. 3 Gas/Air Input (Female 1/4 NPT) 4 Quick Connect Gas Fitting 5 Standard Pipe Fitting (Male 1/4 Inch) Obtain desired fitting.
OM-225 Page 13 L1 2-7. Connecting Input Power input_2 – 3/96 / Ref. ST-144 221 / Ref. ST -070 399-C / Ref. ST -801 390 / ST-801 392 Check input voltage available at site. 1 Input V oltage Selector Switch 2 Selector Switch Label Rotate switch to match input voltage.
OM-225 Page 14 SECTION 3 – OPERA TION 3-1. Controls ST-801 394 12 3 5 1 Power Switch 2 Power Light Power light comes On when Power switch is placed in On position. When unit is turned On, the power light blinks for a short time (3 seconds for 230 V AC, 1 se- cond f o r 460 V AC) to indicate a delay during which the circuits are being initialized.
OM-225 Page 15 3-2. Sequence Of Operation Put On Personal Safety Equipment Install & Connect Equipment EXAMPLE Of Cutting Operation ST-801 400-A Press trigger . Pilot arc starts. Postflow continues for approx. 20 to 30 seconds after releasing trigger; cutting arc can be instantly restarted during postflow by pressing trigger .
OM-225 Page 16 SECTION 4 – MAINTENANCE & TROUBLESHOOTING 4-1. Routine Maintenance Y Disconnect power before maintaining. . Maintain more often during severe conditions.
OM-225 Page 17 4-2. T rouble Lights 1 Pressure Light Lights if gas/air pressure is below 40 PSI (276 kPa). Tur n power Of f, and check for prop- er gas/air pressure (see Section 2-5). 2 Cup Light Lights if shield cup is loose. T urn power Off, and check shield cup connection (see torch Owner ’ s Manual).
OM-225 Page 18 4-4. T roubleshooting T rouble Remedy No pilot arc; dif ficulty in establishing an arc. Clean or replace worn consumables as necessary (see torch Owner ’ s Manual). Check for damaged torch or torch cable (see torch Owner ’ s Manual).
OM-225 Page 19 SECTION 5 – ELECTRICAL DIAGRAM SC-186 187 Figure 5-1. Circuit Diagram.
OM-225 Page 20 SECTION 6 – P ARTS LIST Figure 6-1. Complete Assembly 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 23 32 31 30 27 33 34 37 36 35 39 38 40 41 42 43 44 45 46 47 4.
OM-225 Page 21 Description Part No. Dia. Item No. Figure 6-1. Complete Assembly Quantity Mkgs. 1 126 026 LABEL, warning electric shock 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 171 321 KIT , replacement handle black 2 .
OM-225 Page 22 Description Part No. Dia. Item No. Figure 6-1. Complete Assembly (Continued) Quantity Mkgs. 48 R1,3 181 391 RESISTOR, .3 ohm 140W 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 PC5 181 389 CF PWB, assembly 1 .
OM-225 Page 23 Notes.
OM-225 Page 24 Notes.
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 7/00 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor .
PRINTED IN USA 2000 Miller Electric Mfg. Co. 6/00 Miller Elect ric Mfg. Co. An I l li noi s T ool W orks Company 1635 W est S pencer Street Applet on, W I 5 4914 USA International He adquarte rs .
デバイスMiller Electric OM-225Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miller Electric OM-225Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiller Electric OM-225Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miller Electric OM-225Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miller Electric OM-225Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miller Electric OM-225Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiller Electric OM-225Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miller Electric OM-225Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiller Electric OM-225Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
