PanasonicメーカーHD3700Hの使用説明書/サービス説明書
ページ先へ移動 of 204
Digital Video Cassette Recorder Operating Instructions (Software) AJ- E P.
– 2 – Contents Menu screen transitions . . . . . . . . . . . . . . 4 Turning on the power . . . . . . . . . . . . . . . . 7 HOME menu displays . . . . . . . . . . . . . . . 8 HOME menu . . . . . . . . . . . . . . . . . . . . . 13 HOME SET UP menu .
– 3 – Contents SET UP menu . . . . . . . . . . . . . . . . . . . 111 INTERFACE SET UP menu . . . . . . . . 112 PANEL SET UP menu . . . . . . . . . . . . . 118 PANEL SET UP (OP MAP REMOTE) menu . . . . . . . . . . . . . . . . . . . . . . . . . 120 PANEL SET UP (OP MAP LOCAL) menu .
– 4 – Menu screen transitions HOME F8 HOME SET UP AUDIO IN F6 AUDIO IN PCM INPUT SELECT AUDIO IN CUE INPUT SELECT F7 F8 AUDIO IN SET UP AUDIO OUT F7 AUDIO OUT MONITOR VIDEO IN F7 F7 F10 F9 F9 F10 .
– 5 – Menu screen transitions MUL TI CUE F8 MUL TI CUE SET UP ASSEMBLE ASSEMBLE MANUAL EDIT F8 ASSEMBLE MANUAL EDIT SET UP F12 F12 F1 F2 F3 F4 F5 F6 F7 F10 F1 1 F1 1 F13 F12 HOME SET UP INSERT/ASS.
– 6 – Menu screen transitions TEST F2 RF DIAG F2 DIAG MASKED F3 DIAG LAST F3 AUDIO F4 MECHA F5 SYSTEM F6 FRONT F7 F1 F1 SERVO F13 IC CARD F1 USER MUL TI CUE ERROR LOG F2 F1 TEST FRONT P ANEL F2 TE.
– 7 – Turning on the power Turn on the power. « The HOME menu is displayed. This VTR comes already programmed with menus that correspond to specific operating objectives, and the operations performed on each differ from one menu to another.
– 8 – HOME menu displays ∑ Audio signal display area (Either 8 or 4 channels will be automatically displayed depending on the format used.) Use this to adjust the level of the input audio signals on the AUDIO IN menu. Alternatively, it is used to adjust the level of the audio playback output signals on the AUDIO OUT menu.
– 9 – HOME menu displays REF : This indicates the status of the output reference signal which has been selected by the VTR. HD REF59: HD REF with a field frequency of 59.94 Hz is selected. HD REF47: HD REF with a field frequency of 47.96 Hz is selected.
– 10 – HOME menu displays ∑ Setting mode display area The displays appearing in this area indicate the modes which have been set. CUT: Appears when the audio cut editing mode is set. XFADE: Appears when the audio cross-fade editing mode is set. VFADE: Appears when the audio V fade editing mode is set.
– 11 – HOME menu displays ∑ Setting the initial value for the time code (1) Press the center cursor key. The display now appears in reverse video. (2) Press the center cursor key again so that the cursor is made to serve as a column cursor, and then use the number key to input the value.
– 12 – HOME menu displays ∑ Setting and checking the cue time (1) Press the center cursor key. The time code display now appears in reverse video.
– 13 – HOME menu This menu is displayed by pressing the following key: HOME [4] : Cassette tape in the 4-channel audio format. [8] : Cassette tape in the 8-channel audio format.
– 14 – HOME menu Key F1 F2 F3 F4 F5 F6 F7 Key designation OUTPUT For selecting the audio/video output signals. FREEZE For outputtting the flash freeze frame. EJT CTL For CTL operation in EJECT mode. TC/CTL For timer mode switching. TC/UB For switching the display between the TC and UB values.
– 15 – HOME menu Key F8 F9 – F10 F11 F12 F13 Key designation SET UP —— PREAD A ° For setting audio pre-read to ON or OFF (SD mode only) PREAD V ° For setting video pre-read to ON or OFF (SD mode only). REC INH For setting the record inhibit mode.
– 16 – HOME menu ∑ Pre-read editing (1) Set the pre-read function to ON by pressing the F key and F11 key (PREAD A) or F12 key (PREAD V) together. (2) Perform the connections for pre-read editing as shown in the figure below. (3) Proceed with pre-read editing in the desired insert editing mode.
– 17 – HOME SET UP menu This menu is displayed by pressing the following keys: ) OR ) F1 SET UP F8 HOME F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 18 – HOME SET UP menu Key F1 F2 F3 F4 F5 F6 F7 F8 Key designation SYNC PLY Sync play. AT PLY For switching the playback picture in JOG/VAR. PRG PLAY Program play. PRG PLAY Program play. CAP LOCK ° 3 For setting the capstan servo lock TAPE MD. Tape mode when the VTR is in standby OFF.
– 19 – HOME SET UP menu Key F9 – F10 F11 F12 F13 Key designation —— PREROLL For selecting the preroll time. STILL For setting the STOP/STILL (static frame) mode holding time. STBY OFF For setting the time for the transfer to standbay OFF. Description After pressing the F11 key, turn the ADJUST control.
– 20 – HOME SET UP menu ∑ Reference OUT REF: This sets the video output signal reference. AUTO: When the REF VIDEO connector input sig- nal is available, the output reference is locked to REF VIDEO; when it is not avail- able, it is locked to the INPUT input signal.
– 21 – HOME SET UP menu ∑ Programmed play function (1) Press the F4 (PRG PLY) key. (2) Set the step to FINE or COARSE using the F3 (PRG PLY) key. (3) Set the programmed play speed using the ADJUST control. (4) Press the PLAY and VAR buttons together.
– 22 – VIDEO IN menu This menu is displayed by pressing the following key: VIDEO IN F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 23 – VIDEO IN menu Key F1 F2 F3 – F11 F12 F13 Key designation INPUT For selecting the HD video input signals. INT SG For selecting the type of HD internal signals. —— INT SG For selecting the type of SD internal signals. INPUT For selecting the SD video input signals.
– 24 – VIDEO OUT HD menu This menu is displayed by pressing the following key: VIDEO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 25 – VIDEO OUT HD menu Key F1 F2 F3 F4 F5 – F7 F8 F9 F10 F11 – F13 Key designation For adjusting the Y level. PB For adjusting the P B level.
– 26 – VIDEO OUT HD SET UP menu This menu is displayed by pressing the following keys: > F8 VIDEO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 27 – VIDEO OUT HD SET UP menu Key F1 F2 – 5 F6 F7 F8 F9 – F11 F12 F13 Key designation LINE CONV ° —— SERIAL SYS PHASE INTERP. Interpolation EXIT —— STATE —— Description Line con.
– 28 – VIDEO OUT HD SET UP STATE menu This menu is displayed by pressing the following keys: (or ) >> OR >> (or ) > F12 F12 F11 F9 VIDEO OUT F12 F8 AUDIO OUT VIDEO OUT Description NORMAL: The standard mode is established (E-E through mode is turned OFF).
– 29 – VIDEO OUT SET UP STATE menu ∑ Selecting the TAPE/EE output signals The video, audio and cue signals which are output during the VTR ’ s operation are switched on this menu to TAPE or EE signals. (1) Press the center cursor key to display the cursor.
– 30 – VIDEO OUT SD menu This menu is displayed by pressing the following keys: > F9 VIDEO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 31 – VIDEO OUT SD menu Key F1 F2 F3 F4 F5 – F6 F7 F8 – F9 F10 F11 F12 F13 Key designation Y For adjusting the Y level. PB For adjusting the P B level.
– 32 – VIDEO OUT SD SET UP COMPOSITE menu This menu is displayed by pressing the following keys: >> F11 F9 VIDEO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 33 – VIDEO OUT SD SET UP COMPOSITE menu Key F1 F2 – F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation COMB FIL ° 1 For controlling the comb filter. —— SYS SC For adjusting the system subcarrier. SYS H For adjusting the system H phase. INTERP.
– 34 – VIDEO OUT SD SET UP CMPST STATE menu This menu is displayed by pressing the following keys: (or [AUDIO OUT]) >> OR >> (or ) > F12 F12 F11 F9 VIDEO OUT F12 F8 VIDEO OUT Description NORMAL: The standard mode is established (E-E through mode is turned OFF).
– 35 – VIDEO OUT SD SET UP CMPST STATE menu ∑ Selecting the TAPE/EE output signals The video, audio and cue signals which are output during the VTR ’ s operation are switched on this menu to TAPE or EE signals. (1) Press the center cursor key to display the cursor.
– 36 – VIDEO OUT SD SET UP SDI menu This menu is displayed by pressing the following keys: )) F12 F9 VIDEO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 37 – VIDEO OUT SD SET UP SDI menu ° 1 This adjustment is possible only when the AJ-UDC3700P HD-SD format converter board (optional accessory) has been installed. ° 2 In a mode other than the 525i (480/59i) mode, this adjustment is possible only when the AJ-UDC3700P HD-SD format converter board (optional accessory) has been installed.
– 38 – VIDEO OUT SET UP LINE BLK (video output line blanking) menu This menu is displayed by pressing the following keys: )) (or ) ) . F11 F12 F11 F9 VIDEO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F.
– 39 – VIDEO OUT SET UP LINE BLK (video output line blanking) menu ∑ Setting the line blanking The blanking lines in the vertical blanking period can be set in 1-line increments. (1) Press the center cursor key. The cursor now appears. (2) Move the cursor and select the lines to be blanked.
– 40 – VIDEO OUT SD SET UP SDI STATE menu This menu is displayed by pressing the following keys: (or ) )) OR )) (or ) ) . F12 F12 F11 F9 VIDEO OUT F12 F8 AUDIO OUT VIDEO OUT F13 F12 F1 1 F10 F9 F8.
– 41 – VIDEO OUT SET UP STATE menu ∑ Selecting the TAPE/EE output signals The video, audio and cue signals which are output during the VTR ’ s operation are switched on this menu to TAPE or EE signals. (1) Press the center cursor key to display the cursor.
– 42 – VIDEO OUT CONVERT menu (This menu appears when the AJ-UDC3700P HD-SD format converter board, an optional accessory, has been installed.) This menu is displayed by pressing the following key.
– 43 – VIDEO OUT CONVERT HD_TO_SD menu (This menu appears when the AJ-UDC3700P HD-SD format converter board, an optional accessory, has been installed.
– 44 – VIDEO OUT CONVERT SD_TO_HD menu (This menu appears when the AJ-UDC3700P HD-SD format converter board, an optional accessory, has been installed.
– 45 – VIDEO OUT CONVERT HD_TO_HD menu (This menu appears when the AJ-UDC3700P HD-SD format converter board, an optional accessory, has been installed.) This menu is displayed by pressing the following keys: )) ° This menu is operational when 1080/23.
– 46 – AUDIO IN menu This menu is displayed by pressing the following key: AUDIO IN F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 The digital audio input statuses are displayed here. PRE EMPHASIS ON: Pre-emphasis is applied to the input signals. OFF: Regular signals with no pre-emphasis are supplied.
– 47 – AUDIO IN menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation CH-1 For adjusting the audio CH1 input level. CH-2 For adjusting the audio CH2 input level. CH-3 For adjusting the audio CH3 input level. CH-4 For adjusting the audio CH4 input level.
– 48 – AUDIO IN PCM INPUT SELECT menu This menu is displayed by pressing the following keys: > F6 AUDIO IN F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 49 – AUDIO IN PCM INPUT SELECT menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 Key designation CH-1 For selecting the recording signals of digital audio CH1. CH-2 For selecting the recording signals of digital audio CH2. DIGITAL For selecting the CH1 and CH2 digital input signals.
– 50 – AUDIO IN PCM INPUT SELECT menu Key F10 F11 F12 F13 Key designation CH-6 For selecting the recording signals of digital audio CH6. DIGITAL For selecting the CH7 and CH8 digital input signals. CH-7 For selecting the recording signals of digital audio CH7.
– 51 – AUDIO IN CUE INPUT SELECT menu This menu is displayed by pressing the following keys: > F7 AUDIO IN F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 52 – AUDIO IN CUE INPUT SELECT menu Key F1 F2 F3 F4 F5 – F7 F8 F9 F10 F11 F12 F13 Key designation CH-1 For setting cue mixing for CH1. CH-2 For setting cue mixing for CH2. CH-3 For setting cue mixing for CH3. CH-4 For setting cue mixing for CH4.
– 53 – AUDIO IN SET UP menu This menu is displayed by pressing the following keys: > OR > F6 SET UP F8 AUDIO IN F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 54 – AUDIO IN SET UP menu Key F1 F2 – F5 F6 F7 F8 F9 F10 F11 – F13 Key designation INT SG MD —— PEAK HOLD For setting the peak hold. SCALE For switching the level meter scale. EXIT DATA ADV ° 1 STYLE ° For setting the digital audio input/output data format.
– 55 – AUDIO IN CH-MIX SELECT menu This menu is displayed by pressing the following keys: > F9 AUDIO IN F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 F2 – F5 F6 F7 F8 F9 – F13 Key designation SELECT —— CH-MIX (ON) For mixing the input signals with the signals played back simultaneously and recording them.
– 56 – AUDIO IN CH-MIX SELECT menu ∑ Mix-and-record (1) Press the F6 (CH-MIX) key to set it ON. The mixing graph display now appears. (2) Press the center cursor key to display the cursor. (3) Use the cursor keys to move the cursor to the channel in which the sound is to be mixed.
– 57 – AUDIO IN CH-MIX SELECT menu ∑ Mix-and-record (continued) (5) Move the cursor to the mixing ratio display area, and turn the ADJUST control to set the ratio at which the signals are to be mixed (in 1% increments).
– 58 – AUDIO OUT menu This menu is displayed by pressing the following key: AUDIO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 The digital audio input statuses are displayed here. PRE EMPHASIS ON: Pre-emphasis is applied to the input signals. OFF: Regular signals with no pre-emphasis are supplied.
– 59 – AUDIO OUT menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation CH-1 For adjusting the audio CH1 playback level. CH-2 For adjusting the audio CH2 playback level. CH-3 For adjusting the audio CH3 playback level. CH-4 For adjusting the audio CH4 playback level.
– 60 – AUDIO OUT MONITOR menu This menu is displayed by pressing the following keys: > F7 AUDIO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 61 – AUDIO OUT MONITOR menu Key F1 F2 F3 F4 – F6 F7 F8 F9 – F10 F11 F12 F13 Key designation MODE For selecting the mode. L CH R CH —— A.MONI For selecting the audio monitor output level adjustment.
– 62 – AUDIO OUT SET UP menu This menu is displayed by pressing the following keys: > OR > F7 SET UP F8 AUDIO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 63 – AUDIO OUT SET UP menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 Key designation A/V PHASE ° For adjusting the audio output phase in relation to the video phase. JOG PROC For setting the digital process ON/OFF. VAR PROC For setting the digital process ON/OFF.
– 64 – AUDIO OUT SET UP menu Key F10 F11 F12 F13 Key designation STYLE ° —— STATE —— Description This menu item can be set by pressing the F10 key together with the F key. PCM: The style is set to the normal PCM audio mode. DATA: The style is set to the data mode (compressed audio: Dolby-E).
– 65 – AUDIO OUT SET UP menu ∑ Adjusting the audio output signals in relation to the video signals (1) Press the F1 (A/V PHASE) key to put the display in reverse video. (2) Adjust the phase difference using the ADJUST control. When the ADJUST control is turned, the display changes to VAR.
– 66 – AUDIO OUT SET UP STATE menu This menu is displayed by pressing the following keys: >> F12 F8 AUDIO OUT Description NORMAL: The standard mode is established (E-E through mode is turned OFF). THROUGH: The E-E through mode (AV minimum delay mode) is established.
– 67 – – 67 – VIDEO OUT SET UP STATE menu ∑ Selecting the TAPE/EE output signals The video, audio and cue signals which are output during the VTR ’ s operation are switched on this menu to TAPE or EE signals. (1) Press the center cursor key to display the cursor.
– 68 – AUDIO OUT SDI ASIGN menu This menu is displayed by pressing the following keys: >> F12 F8 AUDIO OUT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 69 – Description Selects the channels whose signals are to be output to HD SDI embedded audio channels 1 through 4. CH1 T 4: The signals of CH1 through CH4 are output. CH5 T 8: The signals of CH5 through CH8 are output. OFF: No signals are output.
– 70 – TC/CHR menu This menu is displayed by pressing the following key: TC/CHR F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 71 – TC/CHR menu Description INT: Built-in time code generator. EXT LTC: LTC time code from TIME CODE input connector. S LTC: LTC time code added to serial signals; not displayed when the SD mode is selected. S VTC: VTC time code added to serial signals; not displayed when the SD mode is selected.
– 72 – TC/CHR menu Description ON: CF BIT is recoorded. OFF: CF BIT is not recorded. ≥ When [EXT LTC], [S VITC] or [S LTC] is selected in the F1 key, the VTR conforms to the external color frame bit. Transfers the VTR to the TC/CHR SET UP menu screen.
– 73 – TC/CHR menu ∑ Changing the superimposing position (1) Move the position using the cursor keys. ≥ When a cursor key is held down, the cursor will move more quickly. ≥ When the center cursor key is pressed, the superimposing re- turns to its initial position.
– 74 – TC/CHR menu ∑ Time code displays and VTR’s operating modes (continued) VTR’s operating modes STOP F.FWD PREVIEW REW REVIEW EDIT PLAY (edit playback) PREROLL EDIT REC (edit recording) .
– 75 – TC/CHR menu Table of user bit settings F1 (SOURCE) INT (internal) TC S LTC S VITC EXT LTC EXT LTC F2 (TC SLAVE) —— —— SLAVE DIRECT F3 (UB SLAVE) ON OFF ON OFF ON OFF F10 (TCR) LTC A.
– 76 – TC/CHR SET UP menu This menu is displayed by pressing the following keys: ) OR ) F5 SET UP F8 TC/CHR F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 77 – TC/CHR SET UP menu Key F1 – F6 F7 F8 F9 F10 F11 F12 F13 Key designation TCG OUT EXIT VITC.L VITC For superimposing VITC onto the SD output. —— VITC For selecting the VITC. LTC For selecting the LTC. Description For selecting whether to latch the TCG display and LTC output using the INPUT CHECK key ° .
– 78 – TC/CHR SET UP VITC.L menu This menu is displayed by pressing the following keys: )) OR )) . F9 F5 SET UP F9 F8 TC/CHR F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 – F7 F8 F9 F10 – F13 Key designation —— EXIT VITC.L —— Description Returns the VTR to the TC/CHR menu screen.
– 79 – TC/CHR SET UP VITC.L menu ∑ Selecting the line where VITC is to be inserted 1. Use the cursor keys ( 2 , 1 ) to select the lines where VITC is to be inserted. The line numbers shown in the boxes on the screen indicate the recommended insertion lines (lines 14 and 16 for NTSC and lines 11 and 13 for PAL).
– 80 – ° 1 This can be set only when the 1080/23p or 1080/24p system format is set and when F11, F12 or F13 key has been set to CONVERT. ° 2 These keys are displayed only when the 1080/23p or 1080/24p system format has been selected.
– 81 – MULTI CUE menu This menu is displayed by pressing the following key: MULTI CUE F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 82 – MULTI CUE menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation 1 For designating the cue number 1 and page. 2 For designating the cue number 2 and page. 3 For designating the cue number 3 and page. 4 For designating the cue number 4 and page.
MULTI CUE menu ∑ Switching the pages ≥ A particular page can be selected by pressing one of the F1 (1) through F5 (5) or F9 (6) through F13 (10) keys together with the F key. ≥ The pages are scrolled up when the F key and “ 1 ” key are pressed together.
– 84 – MULTI CUE menu 4. Move the cursor to the section where the captured time code is to be displayed. 5. Press the COPY key to call the captured time code. 5. The cue data is now entered. ≥ The position of the next cue number automatically appears in reverse video when the F1 (AUTO STEP) key on the MULTI CUE SET UP menu has been set to ON.
– 85 – MULTI CUE SET UP menu This menu is displayed by pressing the following keys: ) F8 MULTI CUE F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 86 – MULTI CUE SET UP menu Key F1 F2 F3 F4 F5 F6–F7 F8 F9 F10 F11 F12 F13 Key designation AUTO STEP For setting the auto step mode. PAG MODE For setting the cursor movement mode. PAG CLR For clearing cue data on a page. —— ALL CLR For clearing all the cue data.
– 87 – INSERT/ASSEMBLE MANUAL EDIT menu Press the (or ) > keys to display the MANUAL EDIT menu. F12 INSERT ASSEM F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 – F7 F8 F9 F10 – F11 F12 F13 Key designation —— SET UP INSERT/ASSEMBLE For setting the editing mode ON/OFF.
– 88 – INSERT MANUAL EDIT CH SELECT menu This menu is displayed by pressing the following keys: >> F13 F12 INSERT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 ° CH-5 to CH-8 are not displayed when PCM audio has been set to the 4-channel format.
– 89 – INSERT MANUAL EDIT CH SELECT menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation VIDEO For selecting the video channel ON/OFF. CH-1 For selecting the audio CH1 ON/OFF. CH-2 For selecting the audio CH2 ON/OFF. CH-3 For selecting the audio CH3 ON/OFF.
– 90 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu Press the (or ) > keys to change to the MANUAL EDIT menu, then press the key to display this menu.
– 91 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu Key F1 F2 – F7 F8 F9 F10 Key designation TIMING ° For setting the edit timing. —— EXIT ERR.STP Error stop. TRACKING For adjusting the tracking. Description Sets the timing with which to record the fields at the edit IN point and OUT point.
– 92 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu Key F11 F12 F13 Key designation CAP LOCK For setting the capstan servo lock. FD TIME ° For setting the audio fade time. MODE ° For setting the audio fade edit. Description For selecting the capstan servo lock mode during playback.
– 93 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu ∑ EDIT REC INHIBIT mode display This display shows the statuses of the editing inhibit modes. ≥ SOFTWARE ≥ The editing inhibit modes selected for each channel are shown here. Refer to “ Selecting the SOFTWARE inhibit channels.
– 94 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu ∑ Selecting the SOFTWARE inhibit channels (1) Press the center cursor key. The cursor now appears. (2) Press the cursor key to move the cursor to the channel where editing is to be inhibited. (3) Press the center cursor key.
– 95 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu ∑ Tracking ≥ Automatically adjusting the tracking (optimizing) To optimize the tracking automatically, press the F10 (TRACKING) key to select OPT ONCE or OPT AUTO. Set the preroll time to 5 seconds or more.
– 96 – INSERT/ASSEMBLE MANUAL EDIT SET UP menu (3) The following message appears and optimizing is suspended in the following cases: ≥ When the VTR is set to a mode other than PLAY while optimizing is underway. ≥ When optimizing has failed. ≥ When no video signals have been recorded on the tape.
INSERT/ASSEMBLE MANUAL EDIT SET UP menu ∑ Selecting the audio fade time (1) Press the F13 (MODE) key to set it to X FADE or V FADE. (2) Press the F12 (FD TIME) key. (3) Turn the ADJUST control to select the audio fade time. O Note N The V fade time is a multiple of the time set for FD TIME.
– 98 – INSERT/ASSEMBLE AUTO EDIT menu The AUTO EDIT menu is displayed by pressing the following keys: or # F12 INSERT ASSEM F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 99 – INSERT/ASSEMBLE AUTO EDIT menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation LAST X For calling the edit data to be input. LAST ED For calling all the last data edited. W/PLYR Continuous VTR remote control ON/OFF. VAR MEMO Variable memory.
– 100 – INSERT/ASSEMBLE AUTO EDIT menu ∑ Tape position indicator This indicates the edit points (IN and OUT) and tape positions of the recorder and player. ≥ EOT (end of tape) or BOT (beginning of tape) is displayed when the tape is at its end or beginning.
– 101 – INSERT/ASSEMBLE AUTO EDIT menu (2) Search the edit point using the search dial. 1) Search the edit point using the search dial. 2) Press the ENTRY button. ≥ Trimming operations (1) Press the center cursor key. The cursor now appears. (2) Press the cursor key to move the cursor to the section with the data to be trimmed.
– 102 – INSERT/ASSEMBLE AUTO EDIT menu Input the data using the scratchpad. 1) Press the center cursor key. The cursor now appears. 2) Press the cursor key to move the cursor to the time code IN or OUT position which is to be input. 3) Press the FROM key.
– 103 – INSERT/ASSEMBLE AUTO EDIT menu ∑ Variable memory function 1. Set the F3 (W/PLYR) key to OFF. W/PLYR 2. Set the F4 (VAR MEMO) key to ON. VAR MEMO ≥ If the IN and OUT points have already been entered, they are automatically cleared. ≥ If ON is set for the split mode, it is forcibly set to OFF.
– 104 – INSERT/ASSEMBLE AUTO EDIT menu ∑ Variable memory editing By operating the search dial on a VTR connected to the unit ’ s RS-422A REMOTE OUT connector or REMOTE IN/OUT connector, the pl.
– 105 – INSERT AUTO EDIT CH SELECT menu This menu is displayed by pressing the following keys: ## F13 F12 INSERT F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 106 – INSERT AUTO EDIT CH SELECT menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation VIDEO For selecting the video channel ON/OFF. CH-1 For selecting the audio CH1 ON/OFF. CH-2 For selecting the audio CH2 ON/OFF. CH-3 For selecting the audio CH3 ON/OFF.
– 107 – INSERT/ASSEMBLE AUTO EDIT SET UP menu This menu is displayed by pressing the following keys: (or ) to change to the AUTO EDIT menu, then press the key OR ) F2 SET UP F8 INSERT ASSEM F13 F1.
– 108 – INSERT/ASSEMBLE AUTO EDIT SET UP menu Key F1 F2 F3 F4 F5 F6 F7 Key designation TIMING ° 1 For setting the edit timing. V PREV Video preview. A PREV Audio preview. PLR SYNC Player synchronization. PREROLL For setting the preroll time. POSTROLL For setting the postroll time.
– 109 – INSERT/ASSEMBLE AUTO EDIT SET UP menu Key F8 F9 F10 F11 F12 F13 Key designation EXIT DLY STRT Delay start. TRACKING For adjusting the tracking. CAP LOCK For setting the capstan servo lock. FD TIME ° 2 For setting the audio fade time. MODE ° 2 For selecting audio fade editing.
– 110 – INSERT/ASSEMBLE AUTO EDIT SET UP menu ∑ Selecting the preroll time (1) Press the F5 (PREROLL) key. (2) Set the preroll time using the ADJUST control.
– 111 – SET UP menu This menu is displayed by pressing the following key: SET UP F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 F2 F3 F4 F5 F6 F7 F8 – F9 F10 F11 F12 F13 Key designation HOME.
– 112 – INTERFACE SET UP menu This menu is displayed by pressing the following keys: ) F10 SET UP F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 113 – INTERFACE SET UP menu Key F1 F2 F3 F4 F5 F6 Key designation P-2 RS-422A Control mode setting. RS-232C PARA 50P parallel remote ON/OFF. AV CONT.
– 114 – INTERFACE SET UP menu Key F7 F8 F9 F10 F11 F12 – F13 Key designation PREREAD For setting pre-read from the remote commands. EXIT UB PRESET For setting the UB preset from remote. VAR LIMT ° V. LEV. CNT —— Description The setting can be changed by pressing the F7 key while holding down the F key.
– 115 – INTERFACE SET UP menu ∑ Table of correlations between modes and connectors MODE-1 connection diagram MODE-2 connection diagram MODE MODE-1 MODE-1 MODE-2 MODE-3 MODE-3 MODE-4 IN Controlle.
– 116 – INTERFACE SET UP menu ∑ Setting the RS-232C parameters (1) Press the F2 (RS-232C) key to set it ON. The parameter display now appears. BAUD RATE: 300, 600, 1200, 2400, 4800, 9600 bps DATA LENGTH: 7 or 8 bits START BIT: 1 bit, fixed STOP BIT: 2 or 1 bit PARITY: None, odd or even (2) Press the center cursor key.
– 117 – INTERFACE SET UP menu ∑ Setting the CH ASSIGN audio channel The commands from a controller which has only analog audio CH1 and CH2 preset commands can be re-read and allotted to the digital audio CH1 to CH4 (or CH1 to CH8 with an 8-channel format) and CUE channels.
– 118 – PANEL SET UP menu This menu is displayed by pressing the following keys: # F11 SET UP F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 119 – Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation SOUND KEY Selection of click sound for function keys and IN/OUT keys. SOUND ALARM Selection of warning sound when error occurs. JOG MAX SP. Jog maximum speed. SHTL L/C/R Shuttle dial clutch ON/OFF.
– 120 – PANEL SET UP (OP MAP REMOTE) menu Press the ## keys to display the OP MAP REMOTE menu. This menu is used to set and display the buttons, keys, controls, etc.
– 121 – PANEL SET UP (OP MAP REMOTE) menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 – F12 F13 Key designation VIDEO For adjusting the video level. AUDIO For adjusting the audio level. TRACKING For selecting the tracking adjustment. MON SEL For selecting the monitor.
– 122 – PANEL SET UP (OP MAP REMOTE) menu ∑ Correlation between F5 (MAP MODE) and F6 (FUNCTION) keys O Notes N ≥ Even when the F6 key has been set to ENABLE on this menu, its setting will be changed to DISABLE if the unit is in the remote control mode and it receives the LOCAL DISABLE com- mand.
– 123 – PANEL SET UP (OP MAP LOCAL) menu Press the ### keys to display the OP MAP LOCAL menu. This menu is used to set and display the buttons, keys, controls, etc.
– 124 – ∑ OP MAP setting method ≥ Those buttons and keys which are marked on the graphics of the control panel shown on the display correspond to the buttons on the actual control panel. ≥ The part corresponding to a key or button which has been pressed on the control button is highlighted.
– 125 – ° The items set using F1 to F7 on the SYSTEM SET UP menu (on pages 131 and 132) are not rewritten even if the factory files are loaded. USER SET UP menu This menu is displayed by pressing the following keys: # F12 SET UP Key F1 F2 F3 F4 F5 F6 – F7 F8 F9 F10 F11 – F13 Key designation LOAD For loading user files.
– 126 – USER SET UP menu ∑ Saving user files Twelve files are provided in this unit. Two of these files are reserved: the LAST file containing the statuses established when the power was last turned off, and the FACTORY file containing the factory statuses (initial settings).
– 127 – USER SET UP menu ∑ Locking user files When locked, the files are protected from subsequent attempts to delete or update their data. (1) Press the cursor keys to select the file to be locked. 1. EDITOR 1 (2) Input the password for files 1 to 4.
– 128 – USER SET UP menu ∑ Deleting user files Unnecessary files can be deleted. (1) Press the cursor keys to select the file to be deleted. 5. EDITOR 2 (File locked) (2) Check that the file to be deleted is unlocked. If it is locked, refer to the section on locking the user files, and unlock the file.
– 129 – USER SET UP menu ∑ Copying user filenames When a file is to be given the same name, the filename is copied. (1) Press the cursor keys to select the filename to be copied. 1. EDITOR 1 (2) Press the FROM key. 1. EDITOR 1 (3) Press the cursor keys to select the number of file serving as the copy destination.
– 130 – SYSTEM SET UP menu This menu is displayed by pressing the following keys: ) The system format and video output format currently set in the menu are displayed.
– 131 – SYSTEM SET UP menu (Refer to the setting flowchart and output status tables on pages 134 and 135.) Exactly Which operation is performed differs depending on whether the AJ-UDC3700P HD-SD format con- verter board, an optional accessory, has been installed.
– 132 – Key F5 F6 Key designation HD SDI HD MONI Description For selecting the HD SDI MAIN output format. When the F5 key is pressed while holding down the F key, the HD SDI MAIN output format selection window is opened. The format can now be selected using the cursor keys (but only when “ 23.
– 133 – Key F7 F8 F9 F10 F11 F12 – F13 Key designation SD SDI EXIT A.REC.GRD —— PB AUTO —— Description For selecting the format in which the signals are to be output to SD SDI MAIN. When the F7 key is pressed while holding down the F key, the HD SDI MAIN output selection window is opened.
– 134 – F1: SYSTEM frequency setting ≥ F1 backlighting comes on. ≥ Displays go off inside VTR STATUS windows. ≥ SYSTEM frequency window opens. Use > cursor to select frequency. ( ≥ Backlighting goes off at same time as frequency is entered.
– 135 – SYSTEM SET UP menu System format and video output status table [When the AJ-UDC3700P HD-SD format converter board (optional accessory) has been installed] F1: FREQ 59.94 23.98 24 50 F3: VIDEO 1080I 720P 525I (1080PsF) (1080PsF) (1080I) F4: AUDIO 4ch 8ch 4ch 8ch (4ch) (8ch) (8ch) (8ch) F5: HD SDI (1080/59.
– 136 – ENGINEER SET UP menu This menu is displayed when the > and keys are pressed together. F F13 SET UP F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 – F7 F8 F9 F10 – F13 Key designation —— EXIT OPERATION —— Description Returns the VTR to the SET UP menu screen.
– 137 – OPERATION ENGINEER SET UP menu This menu is displayed when the > and keys are pressed together, and then the F9 key is pressed. F F13 SET UP F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 .
– 138 – TEST menu This menu is displayed when the key is pressed. TEST F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 F2 F3 F4 F5 F6 F7 F8 – F12 F13 Key designation —— RF AUDIO MECHA SYSTEM FRONT SERVO —— IC CARD Description Transfers the VTR to the RF TEST menu screen.
– 139 – TEST menu ∑ OPERATION TIME display How long the VTR has been used for appears on this display. OPERATION: Total power-on time HEAD ROTATION: Cumulative head drum rotation time TAPE TRAVE.
– 140 – RF TEST menu This menu is displayed by pressing the following keys: > F2 TEST F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 141 – RF TEST menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 – F10 F11 F12 F13 Key designation EECC SMPL Change of error rate measurement time. METER Switch of meter display. —— LOAD Load of default value. —— MODE CH EXIT —— ADJ RF RF adjustment value display.
– 142 – RF TEST menu ∑ Error rate display The error rates (error occurrence rates) are indicated on the 1) TOTAL ERROR and 2) INNER ERROR displays. 1) TOTAL ERROR During recording, the error rate of the simultaneous playback signals is displayed.
– 143 – RF adjustment value display menu F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 – F5 F6 F7 F8 – F10 F11 F12 Key designation —— ADJ MODE Adjust mode. ADJ CH —— ADJ RF RF adjustment value display. ADJ SEL Description FIX: Holds the current adjusted value.
– 144 – AUDIO TEST menu This menu is displayed by pressing the following keys: > F3 TEST F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation CH-1 CH-2 CH-3 CH-4 CUE MONI.L MONI.R EXIT REF.LEV IMPED.
– 145 – MECHA TEST menu This menu is displayed by pressing the following keys: > F4 TEST F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 The menu below is displayed when the key is pressed.
– 146 – Key F1 F2 F3 F4 F5 F6 – F7 F8 F9 – F13 Key designation MODE Loading without tape. —— C.SIZE Cassette size selection. —— SENSOR Sensor operation check. —— EXIT —— Description NORMAL: Normal operation. NO-TAPE: Loading without cassette tape is possible.
– 147 – SYSTEM TEST menu This menu is displayed by pressing the following keys: # . This menu contains keys for adjustments by service personnel. General users cannot operate these keys.
– 148 – SERVO TEST menu This menu is displayed by pressing the following keys: # . F7 TEST F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1.
– 149 – SERVO TEST menu Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Key designation TORQUE Reel torque adjustment. DATA SEND Torque data forwarding. MEASURE (Measure) AT AT head adjustment. METER PG SHIFT PG shifter adjustment. ADJ RATE Adjust rate.
– 150 – SERVO TEST menu ∑ Error rate display The error rates are displayed in terms of the 1) TOTAL ERROR and 2) INNER ERROR. For details, refer to the description of the error rate display for the RF TEST menu (on page 142).
– 151 – TEST FRONT menu This menu is displayed by pressing the following keys: # F6 TEST Key F1 F2 F3 – F7 F8 F9 – F13 Key designation PANEL Display check. KEYCHECK Front panel key check. —— EXIT —— Description Transfers the VTR to TEST FRONT PANEL menu screen.
– 152 – Key F1 F2 – F7 F8 F9 – F13 Key designation MODE Display dot check. —— EXIT —— Description The entire display panel is lighted up in a fixed pattern and display dots are checked. Each time the key is pressed, 12 types of pattern are displayed.
– 153 – TEST FRONT KEY CHECK menu This menu is displayed by pressing the following keys: ## . F2 F6 TEST F13 F12 F1 1 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 Key F1 – F7 F8 F9 – F13 Key designation —— EXIT —— Description Returns the VTR to the TEST FRONT menu screen.
– 154 – TEST FRONT KEY CHECK menu ∑ Dial and controls When the ADJUST control, headphones control or search dial is turned, the number of pulses counted is displayed. ∑ LEDs Each time the F1 key is pressed, the LEDs on the panel light up in sequence and are checked.
– 155 – Inserting the IC card The insertion slot for the IC card is located on the back left of the front panel. Insert the IC card before using the TEST IC CARD menu.
– 156 – TEST IC CARD menu This menu is displayed by pressing the following keys: > F13 TEST Description User file management takes place using IC card. When the F key is pressed, transfer is made to TEST IC CARD USER FILE menu. ≥ There is a load/save function for current (present deck status) and all registered files.
– 157 – TEST IC CARD USER menu This menu is displayed by pressing the following keys: >> . F1 F13 TEST Description Calls out IC card user file. (Executes when pressed together with F key.) Registers IC card user file. (Executes when pressed together with F key.
– 158 – TEST IC CARD MULTI CUE menu This menu is displayed by pressing the following keys: >> F2 F13 TEST Description Loads file registered from IC card to deck. ≥ Executes when pressed together with F key. When there is a page on which writing is prohibited, the message “ PROTECTED PAGE ” appears and the function is not executed.
– 159 – TEST IC CARD MULTI CUE SELECT menu This menu is displayed when the >> > and keys are pressed together. F1 F F2 F13 TEST Description Selected files are loaded from IC card to deck by pressing the UP_LD key after selection of the pages to be forwarded.
– 160 – TEST IC CARD MULTI CUE MONITOR menu This menu is displayed by pressing the following keys: >> > . F3 F2 F13 TEST Description Returns the VTR to the TEST IC CARD MULTI CUE menu screen. Key F1 – F2 F3 – F7 F8 F9 – F13 Key designation —— 1 – 5 Designation of 1 – 5 cue number.
– 161 – TEST IC CARD ERROR LOG menu This menu is displayed by pressing the following keys: >> F3 F13 TEST Description Loads current memory data from VTR to IC card.
– 162 – TEST IC CARD ERROR LOG MONITOR menu This menu is displayed by pressing the following keys: >> > keys are pressed. To check the current log data of the VTR, first download the machine current data, and then monitor the log data. F2 F3 F13 TEST Description Returns the VTR to the TEST IC CARD ERROR LOG menu screen.
– 163 – Error messages Four kinds of error messages are displayed by this VTR. (1) DIAG menu A warning mark (W) blinks at the top left of the menu screen when an erroneous setting, failure to verify a condition, warning or other problem that interferes with the use of the VTR has arisen.
– 164 – DIAG menu error messages A warning mark (W) blinks at the top left of the screen when an er- roneous setting, failure to verify a condition, warning or other problem that interferes with the use of the VTR has arisen. If the DIAG key is pressed while a warning is shown, an error message appears on the screen.
– 165 – DIAG ACTIVE menu When the DIAG key is pressed while the warning mark is displayed, the DIAG ACTIVE menu below appears. Description Transfers the VTR to the DIAG MASKED menu screen. Transfers the VTR to the DIAG LAST menu screen. Masks (cancels) the warning currently on display in the DIAG ACTIVE menu.
– 166 – ∑ When there are 2 or more canceled (masked) warnings ≥ Error messages are displayed from item of highest priority. ≥ All the messages can be viewed sequentially by operating the cursor and the up/down arrow keys. ≥ Total number of warnings is displayed.
– 167 – ∑ When 2 or more warnings have occurred ≥ Error messages are displayed from item of highest priority. ≥ All the messages can be viewed sequentially by operating the cursor and the up/down arrow keys.
– 168 – DIAG error messages Message FAN STOP1 FAN STOP2 NO CUE ERASE CURRENT NO TC ERASE CURRENT NO FULL ERASE CURRENT NO CTL ERASE CURRENT COMP. CPU NOT RESPONDING VIDEO CONCEAL SW OFF INNER ECC .
– 169 – DIAG error messages Message WRONG OPTIMIZED TRACKING VALUE SERVO UNLOCKED BEFORE IN POINT NO EXTERNAL HD REF NO EXTERNAL SD REF NO COLOR BURST IN SD REF NO STANDARD SCH-RANGE IN REF NO HD .
– 170 – DIAG error messages Message INPUT DIGITAL AUDIO CH5/6 SYNC ERROR CONFIRM INPUT DIGITAL AUDIO INPUT DIGITAL AUDIO CH7/8 SYNC ERROR CONFIRM INPUT DIGITAL AUDIO INPUT AUDIO CH1/2 CRCC ERROR C.
– 171 – DIAG error messages Message SUM-CHECK ERROR IN RECEIVED COMMAND FROM RS-232C PORT PARITY ERROR IN RECEIVED COMMAND FROM RS-232C PORT FRAMING ERROR IN RECEIVED COMMAND FROM RS-232C PORT OVE.
– 172 – AUTO OFF error messages If a problem has occurred and the VTR cannot continue operating or the mechanism or tape may be damaged by continued operation, the AUTO OFF lamp on the VTR ’ s front panel come on, the buzzer sounds, and an error message appears on the screen.
– 173 – AUTO OFF error messages Message CPU TAPE HANDLE TROUBLE CPU (SERVO SYS) COMM. TROUBLE CASSETTE PHOTO SENSOR TROUBLE DETECTION SWITCH FAIL (A) DETECTION SWITCH FAIL (B) DETECTION SWITCH FAI.
– 174 – SYSTEM error messages When a problem has occurred in the VTR and its operation can no longer be guaranteed, the system error lamp comes on, the buzzer sounds, and an error message appears on the screen. In this situation, stop operating the VTR immediately, and proceed to fix the trouble.
– 175 – SYSTEM error messages Message AV NOT RESPONDING SYSCON NOT RESPONDING S2 BOARD NOT RESPONDING S3 BOARD NOT RESPONDING S4 BOARD NOT RESPONDING S5 BOARD NOT RESPONDING L1 BOARD NOT RESPONDIN.
– 176 – Operation messages In the majority of cases, when a mistake has been made in operating a button or key during automatic editing, a message appears at the bottom right of the screen (above the tape speed display) telling the user how to proceed with operation.
– 177 – Operation messages (in AUTO EDIT mode) No. 350 351 352 353 354 355 356 357 359 360 361 362 363 Message NO CASSETTE NO PRESET NO IN POINT NO PLY ’ R MODE NOT REC ’ R MODE NEGATIVE DURAT.
– 178 – Screen saver function This function is designed to prolong the service life of the VTR ’ s large display screen. The screen ’ s life may be shortened when the screen continuously displays menu screens on which no move- ment is occurring.
Menu HOME HOME SET UP VIDEO IN VIDEO OUT HD – 179 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set.
– 180 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item LIN CONV SERIAL SYS PHASE INTERP. EXIT STATE Selection item ON OFF n 1375 SAMPLE n 1320 SAMPLE n 1100 SAMPLE n 825 SAMPLE AUTO OFF Transfers VTR to menu screen.
– 181 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item EE_MODE EXIT STATE Selection item NORMAL THROUGH Transfers VTR to menu screen.
– 182 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item HD_TO_SD SD_TO_HD HD_TO_HD HD SD Selection item Transfers VTR to menu screen.
FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 – 183 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set.
– 184 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item SELECT CH-.
– 185 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item EE_MODE EX.
– 186 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item EXIT VTIC.
– 187 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 188 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 189 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 190 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 191 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 Setting item MODE C.
– 192 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 193 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 194 – List of menu screen displays The underlined setting in the selection item column denotes the mode initially set. FUNC key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 FUNC key F1 F2 F3 F4 F5.
– 195 – INDEX [A] Menu/function keys/pages Alarm tone setting PANEL SET UP/F2/119 Assemble editing: Automatic editing AUTO EDIT/F12/99 Manual editing MANUAL EDIT/F12/87 AT head hysteresis removal .
– 196 – INDEX [B] Menu/function keys/pages Black level adjustment VIDEO OUT HD/F4/25 VIDEO OUT SD/F4/31 [C] Capstan servo lock setting MANUAL EDIT SET UP/F11/92 AUTO EDIT SET UP/F11/109 Automatic .
– 197 – INDEX [E] Menu/function keys/pages Editing: Editing channel selection during automatic editing INSERT AUTO EDIT CH SELECT/F1 – F7, F9 – F12/106 Editing channel selection during manual .
– 198 – INDEX [ I ] Menu/function keys/pages IC card TEST/F13/143, 155 – 162 Input signal selection VIDEO IN/F1, F13/23 Insert editing: Automatic editing AUTO EDIT/F9, F12/99 Editing channel sel.
– 199 – INDEX [O] Menu/function keys/pages OP MAP setting method: Local PANEL SET UP (LOCAL) / — /124 Remote PANEL SET UP (REMOTE) / — /121, 122 Operation messages — / — /176, 177 Operatio.
– 200 – INDEX [S] Menu/function keys/pages Search dial: Jog speed selection, maximum PANEL SET UP/F3/119 Shuttle clutch point setting PANEL SET UP/F4 – F5/119 Shuttle maximum speed selection PAN.
– 201 – INDEX [U] Menu/function keys/pages User bit: List of settings TC/CHR/ — /75 Slave lock mode setting TC/CHR/F2/71 User bit value display HOME/F5/14 User files: Automatic file call at powe.
– 202 –.
– 203 –.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 EASTERN ZONE: .
デバイスPanasonic HD3700Hの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Panasonic HD3700Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic HD3700Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic HD3700Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic HD3700Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic HD3700Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic HD3700Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic HD3700Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic HD3700Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。