PanasonicメーカーTY-SP42PM3Wの使用説明書/サービス説明書
ページ先へ移動 of 59
P edestal TY -ST42PT3S TY -ST42PT3K W all stand TY -ST42PW1 Mobile stand TY -ST42PF3 W all-hanging brac ket (vertical) TY -WK42PV1 W all-hanging brac ket (angled) TY -WK42PR1 Ceiling unit TY -CE42PS1 .
Ho w to use this manual Some notes on ho w to read this manual In this manual, the n umber such as "1, 2, 3,..." appears to the left of each step. Go ahead in numerical order . Indicates a situation where incorrect handling ma y result in death or serious injur y f or the person performing the installation.
Bef ore installing Be sure to read through these instructions before starting the installation. The installation should be only perf or med b y a professional person. If any parts are not installed correctly , the display unit ma y f all, possibly resulting in damage and personal injury .
T ools list The tools in the f ollowing tables are necessary for complete assemb ly . Bef ore attempting to install the accessories, make sure you ha v e the following tools on hand.
Accessory list TY-ST42PT3-S TY-ST42PT3-K TY-ST42PW1 Pedestal Wall-hanging bracket (vertical) Wall-hanging bracket (angled) Wall stand 1 2 4 5 TY-WK42PR1 TY-WK42PV1 TY-ST42PF3 Mobile stand 3 TY-CE42PS1.
P ar ts list Check the part number before perf orming the installation procedure. Base Assembly scre w(M5-20) x 4 Assembly scre w (M5-30) x 4 P edestal W all pedestal Holding brac ket Allen ke y (acce.
W all-hanging bracket unit Fixing screw (M5) x 2 P an head bolt with hex soc ket (M8-45) x 4 T ooted pan washer x 4 Insulating spacer x 4 W all-hanging bracket unit Fixing screw (M5-35) x 2 P an head .
Ceiling unit Fixing bolt (M8-12) x 2 Ceiling unit Allen ke y Fixing bolt (M8-100) Spring washer Washer pan n ut (M8) Fixing screw (M5) x 2 Fixing bolt (M8-20) x 2 Cable tie x 2 P an head bolt with he .
Dimensions of the displa y unit S-VIDEO VIDEO VD HD P R /C R /R P B /C B /B Y/G L R L R AUDIO A UDIO AUDIO SERIAL TUNER IN PC IN COMPONENT/RGB IN A V IN 1020 920 50 610 518 615 89 50 22 18.5 35.7 70.69 296 18 18 18 18 20 53.86 98 39.43 46 46 489 44 112.
.
1- 1 P edestal TY -ST42PT3S TY -ST42PT3K Assembl y diagram CONTENTS Instruction of the installation ...................... 1- 2 1.Assembling the pedestal .................................... 1- 2 2.Attaching the pedestal to the displa y unit .........
1- 2 Instruction of the installation Assembling the pedestal Attaching the pedestal to the displa y unit Ensure that the poles sit flush with the bottom of the base. Place the displa y face down on a cloth clean and free from other f oregin par ticles, and then proceed to the ne xt step .
1- 3 Insert the four screws, two on eac h side, into the holes in the bac k of the displa y unit and screw them into the holes on the inserted poles. 3 Front Rear Fixing the displa y unit Insert the two poles at the top of the pedestal into the holes in the base of the display unit as sho wn in the illustration below .
1- 4 Fixing the displa y unit to the wall Insert the screws and clamp into the holes at the bac k of the display unit. 1 Use a strong wire or chain commer cially a vailable to fix the display unit to a solid area of the wall or pillar .
2- 1 Assembl y diagram CONTENTS Description ................................................... 2- 2 Instruction of the installation ...................... 2- 3 1.Assembling the w all stand .................................. 2- 3 2.Fixing the insulating spacers to the displa y unit .
Description Installation diagram 400 (15 3 / 4 ) 610 (24 1 / 64 ) 1116.5 (43 61 / 64 ) 611.5 (24 5 / 64 ) 744 (29 19 / 64 ) 1020 (40 5 / 32 ) 560 (22 1 / 16 ) 390 (15 23 / 64 ) 89 (3 33 / 64 ) 19 ( 3 / 4 ) *100 Units : mm 2- 2 * A clearance of at least 100mm at the top of the displa y unit should be provided.
Instruction of the installation Assembling the wall stand Refer to the holding brack et installation measurements in the drawing left. Ensure that the wall is ab le to bear the weight at each of the 4 upper and lower installation locations. Add reinf orcement if any of these locations are not strong enough.
Fix a M6 screw , through an y of the slits in the bracket, into the corresponding hole in the wall. Using a lev el along the top or bottom edge, ensure that holding br acket is horizontal. 2 Fix the screws thr ough the slits into the remaining three holes.
Remove the f our screws. 2 As shown in the illustration, use the supplied "Allen key" to fasten the screw thr ough and , then screw the four to the display unit.
Attaching the wall stand to the displa y unit Insert the two poles at the top of the wall pedestal into the holes in the base of the display unit as sho wn in the illustration. 1 Insert the four scre ws, tw o on either side , into the holes in the back of the display unit and fasten them into the holes in the inserted poles.
Fixing the displa y unit to the wall Lift the display so that the upper insulating spacer s at the back ma y fit into the notched indentation at the top of the holding brac ket, and then lower the displa y into place .
Remo ve the two fixing screws fr om the sides of the holding bracket. 1 1) Lift the display slightl y; 2) Pull the bottom half wa y to detach the lower insulating spacer s; 3) Lift the display a way from the holding brac ket.
Assembl y diagram CONTENTS Description ................................................... 3- 2 Instruction of the installation ...................... 3- 3 1.Assembling the mobile stand .............................. 3- 3 2.Fixing the displa y unit to the stand .
Description Installation diagram Units : mm 1020 (40 5 / 32 ) 610 (24 1 / 64 ) 1637 (64 29 / 64 ) 1030 (40 9 / 16 ) 650 (25 19 / 32 ) 400 (15 3 / 4 ) 15 ° 89 (3 33 / 64 ) 820 (32 5 / 16 ) 3- 2.
Instruction of the installation Assembling the mobile stand Slide the shelf, with the supports in the slots, do wn to the required height. Choose the locations of stopper holes to match the required height. Then fix the shelf using the four screws and spring washers.
Fixing the displa y unit to the stand Lock the casters bef ore installing the displa y unit. Press down the caster switch to loc k the caster . Unlock Lock 1) Spread a clean c loth over a le vel floor or base , and place on it the display unit face do wn.
Fixing the wiring Insert the accessrory cable straps, evenly spaced, into the appropiate mounting holes in the rear of the support. 1 Cable Cablestraps Bring together the input cables which are connected to the terminals at the bottom of the display unit and secure them with the five cab le straps.
Loosen and remo ve the four screws fr om the display unit. 1 Remo ving the displa y unit Lift the displa y unit away fr om the stand. 2 2 1 3- 6.
4- 1 W all-hanging brac ket (ver tical) TY -WK42PV1 Assembl y diagram CONTENTS Description ................................................... 4- 2 Instruction of the installation ...................... 4- 4 1.Fixing the wall-hanging br ack et to the wall .
Description Installation diagram Units : mm 4- 2 * A clearance of at least 100mm at the top of the displa y unit should be provided. 660 450 20 320 610 900 450 450 1020 69.
4- 3 Installation diagram For Multi Screen Units : mm 90 120 * Installe lower panel unit first..
Instruction of the installation Fixing the wall-hanging brac ket to the wall Check the strength of the installation location The wall-hanging brac ket weighs appro ximately 6kg, and the displa y unit by itself weighs 33kg.
If required, use commer- cially av ailable M6 bolts which suit the wall materials. If the Screws protrude more than 5 mm, it will not be possible to install the Wide Plasma Displa y in the correct position. Place the displa y unit f ace down on top of a cloth clean and free from otherforegin particles, and then proceed to the ne xt step.
Lift the displa y unit so that the upper insulating spacers at the back may fit into the notc hed indentation at the top of the wall-hanging brac ket, and then lo wer the display unit into place.
1) Lift the display slightl y; 2) At the same time, pull the bottom half way to detach the lo wer insulating spacers; 3) Lift the display a way from the wall-hanging brac ket. 2 Remo ving the displa y unit 1 Remo ve the two fixing screws fr om the sides of the wall-hanging bracket.
W arning IF UN OFFICIAL BRA CKET IS USED . Do not fix. The displa y unit with un official brack et by bolts directly , the display unit ma y damage and possibly electrical interfalance f or other electronics equipment.
CONTENTS Description ................................................... 5- 2 Instruction of the installation ...................... 5- 3 1.Fixing the wall-hanging br ack et to the wall ............ 5- 3 2.Adjusting the angle of the displa y fitting .
Description Installation diagram Units : mm 5- 2 450 450 450 20 490 660 900 1020 930 89 610 **310 *100 * A clearance of at least 100mm at the top of the display unit should be pro vided. ** Installation of the wall-hanging brac ket requires a depth of 310 mm.
Instruction of the installation Fixing the wall-hanging brac ket to the wall The wall-hanging br ack et has installation holes provided at 14 locations . If the wall material does not allow sufficient strength by using six installation holes, use some of the spare holes.
Adjusting the angle of the displa y fitting If the screws protrude more than 5 mm, it will not be possible to install the Wide Plasma Displa y in the correct position. Use a level gauge to correct the alignment of the wall-hanging brac ket, and screw bolts into the remaining five holes.
Place the displa y unit f ace down on top of a cloth clean and free from otherf oregin par ticles, and then proceed to the ne xt step. Spread a clean c loth over a le vel floor or base, and place on it the displa y unit face down. Remo ve the four screws from the displa y .
5- 6 Do not lift the displa y too high or it ma y come out of the notches in the upper indentations . Insert and fasten the screws at both the left and right sides. 4 T o pre vent the displa y unit from becoming detached from the w all- hanging brac ket, make sure that the left and right fixing screws are properly fitted.
Remo ving the displa y unit 1 Remo ve the two fixing screws fr om the sides of the wall-hanging bracket. Insulating spacer Foxing screws (left and right) 3) 1) 2) 1) Lift the display unit slightl y; 2) At the same time, pull the bottom half way to detach the lo wer insulating spacers; 3) Lift the display a way from the wall-hanging brac ket.
6- 1 Assembl y diagram CONTENTS Description ................................................... 6- 2 Instruction of the installation ...................... 6- 3 1.Assembling the ceiling unit ................................. 6- 3 2.Prepare the ceiling unit .
Description Installation diagram Units : mm (in.) 626 ~ 926 Ceiling board 50 431 660 89 6- 2.
Instruction of the installation Assembling the ceiling unit Units : mm (in.) 300 (11 26 / 32 ) 300 (11 26 / 32 ) 350 (13 25 / 32 ) Ceiling installation holes Front 24 ( 15 / 16 ) 14 ( 35 / 64 ) R7 (R 9 / 32 ) 6- 3 Ceiling unit (upper section) Fixing bolt (M8-12) Ceiling unit (lower section) Check the strength of the installation location.
6- 4 Flat washer (not supplied) Spring washer (not supplied) M12 bolt (not supplied) Earthed mains extension lead (example) Signal cable (example) • Reinf orce the ceiling if it is not strong enough. • Use bolts appropriate for the ceiling material (not supplied).
6- 5 When adjusting the height, no more that 4 holes should be visible . (The white line should not show .) Distance from center of display to ceiling ( in.
Prepare the displa y . 1 6- 6 Quite los cuatro pernos. P an head bolt with he x socket T oothed pan washer Insulating spacer Install the insulating spacers in the displa y unit. La y the display with the screen f acing down on a clean b lanket or sheet and f ollow the steps below .
Mount the displa y in the ceiling unit. Hook the displa y’s top insulating spacers in the ceiling unit by aligning the display with the notc hes in the ceiling unit and sliding the display downwar d.
6- 8 4 Adjust the ceiling unit's direction. Adjust the angle of the display and fix in place with two fixing bolts (M8-20, included). Connecting pipe Angle adjustment hole positions 0 ° (vertical) 5 ° 10 ° 15 ° 20 ° 25 ° 30 ° 5 Adjust the ceiling unit's angle.
6- 9 6 Gather the cables. Gather the cables connected to the terminals on the back of the displa y and fix in place with a cable tie . Cable Cable tie Cable tie Cable Cable tie x 2.
Remo ving the displa y unit 6- 10 1) Lift the lower part of the display , 2) pull outwar d 3) and lift upward. 2 1 Remo ve the two fixing screws (M5) at the left and right sides of the ceiling unit.
7- 1 Assembl y diagram CONTENTS Description ................................................... 7- 2 Safety Precautions ....................................... 7- 2 Instruction of the installation ...................... 7- 3 1.Attach the sponges to the speak ers .
Description Installation diagram Units : mm (in.) 7- 2 Saf ety Precautions Do not suspend the speakers. P ersonal injur y ma y result if the speakers fall do wn. T ake particular care to ensure the safety of children. These speakers are f or use with the Wide Plasma Display only .
Instruction of the installation 7- 3 Attach the sponges to the speaker s. Sponges For right For left • Attach the sponges to the surf aces which are in contact with the Display . • Clean the surf aces bef ore attaching the sponges. Attach the mounting brac kets to the speaker s.
Attach the speaker s to the Wide Plasma Displa y . • Inser t the hooks on the top and bottom mounting brack ets simultaneously into the slots at the rear of the Wide Plasma Display , and then low er the speaker into place . • Attach the left speaker in the same w ay .
7- 5 1. If connecting to an external amplifier which exceeds the rated input f or the speakers, low er the amplifier v olume to protect the speakers from damage. If any prob lems occur with speaker operation, disconnect the mains lead of the amplifier and consult a qualified service technician.
Matsushita Electric Industrial Co., Ltd. Central P .O . Bo x 288, Osaka 530-8692, Japan.
デバイスPanasonic TY-SP42PM3Wの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic TY-SP42PM3Wをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic TY-SP42PM3Wの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic TY-SP42PM3Wの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic TY-SP42PM3Wで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic TY-SP42PM3Wを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic TY-SP42PM3Wの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic TY-SP42PM3Wに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic TY-SP42PM3Wデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
