SamsungメーカーSSA-R2001の使用説明書/サービス説明書
ページ先へ移動 of 18
RFID Reader User Manual SSA-R2001 imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website.
2_ Safety information safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE.
English 3 SAFETY INFORMATION Keep out of direct sunlight and heat radiation sources. It may cause fi re. Install it in a place with good ventilation. Avoid aiming the controller directly towards extremely bright objects such as sun.
4_ Contents contents PRODUCT INTRODUCTION 5 5 Features 5 What’s included 6 At a Glance 7 Cable Color Scheme 7 Cable Selection INSTALLATION AND EXTERNAL CONNECTION 8 8 Installation 9 Precautions on i.
English 5 PRODUCT INTRODUCTION FEATURES This product is an elegant-looking proximity reader equipped with the built-in keypad, which has the maximum of 10cm (4”) read range. It is also supported by backlighting on the keypad, enabling stable operation at night.
6_ Product Introduction product introduction AT A GLANCE Front/Rear 1 LED Displays the status of the system operation. 2 Keypad Used to enter the ID/password. 3 2-PIN Connector Can be connected to the power cable. 4 6-PIN Connector Can be connected to Wiegand, RS-232 communication cables.
English 7 PRODUCT INTRODUCTION CABLE COLOR SCHEME 2-PIN Connector I/O Pins Signal Cable Color Power (+12V) DC +12V Re d Earth-grounding GND (-) Black 6-PIN Connector I/O Pins Signal Cable Color Wiegan.
8_ Installation and External Connection installation and external connection INSTALLATION Attach the provided rear panel to the wall and drill two 6-32 holes and one 1/2 inch hole on it. (See [Figure 1]) Refer to [Figure 2] below on how to secure the rear panel to the wall using the provided screws.
English 9 INSTALLATION AND EXTERNAL CONNECTION PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below.
10_ Installation and External Connection installation and external connection EXTERNAL CONNECTION WIRING DIAGRAM Category Cable Color Power Supply Unit Connect the DC+12V to the red line. Connect GND to the black line. Wiegand Connection Connect the green line of the product to the Wiegand D0 input port of the controller.
English 11 INITIALIZATION initialization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad. You can select 4/8 bit Burst or 34bit Wiegand. Adjust the format according to the controller receiving the keypad input. To change the output format, use the switch on the rear of the product.
12_ Initialization initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card Present the card to the product until you hear a beep and the green indicator turns on.
English 13 OUTPUT FORMAT output format WIEGAND OUTPUT Timing Diagram Data Format (34-bit) Bit 1 : Even Parity (bit 2 ~ bit 17) Bit 2~Bit33 : 4-byte ID Number Bit 34 : Odd Parity (bit 18 ~ bit 33) • .
14_ Output Format output format RS-232 OUTPUT Output Waveform Data Type START (0X02H) DATA (10 Char) END (0x03H) LRC START(0X02H) DATA (10 Char) END (0x03H) LRC Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC : This is the result of XOR operation of each byte from Start to End.
English 15 OUTPUT FORMAT 4/8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 0000 0 6 0110 6 1 0001 1 7 0111 7 2 0010 2 8 1000 8 3 0011 3 9 1001 9 4 0100 4 E.
16_ troubleshooting troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you. PROBLEM SOLUTION My card is not read properly.
English 17 product specifi cations PRODUCT SPECIFICATIONS Item SSA-R2001 Power / Current DC 12V / Max.75mA Reading Time (Card) 30ms Input Port 2 ea : External LED Control, External Buzzer Control Out.
AB82-02555A Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life.
デバイスSamsung SSA-R2001の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Samsung SSA-R2001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung SSA-R2001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung SSA-R2001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung SSA-R2001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung SSA-R2001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung SSA-R2001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung SSA-R2001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung SSA-R2001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
