Chamberlainメーカー2000SDの使用説明書/サービス説明書
ページ先へ移動 of 36
TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3.
Start by re viewing these important safety alert symbols: 2 Safety alert symbol re view ............................................2 Safety information and precautions ..............................3 T esting your garage door for binding & balance .
3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice.
4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2).
Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex.
ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door .
• Open your door to the highest point of trav el as shown. Dra w an inter- secting horizontal line on the header wall 3" abo ve the high point. This height will provide tra vel clearance for the top edge of the door .
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door .
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door .
The safety re versing sensor must be connected and aligned correctly bef ore the garage door opener will move in the do wn direction. This is a requir ed safety device and cannot be disabled. Installation pr ocedur es ar e the same for sectional and one-piece doors.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el.
Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring.
Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley .
Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on.
T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet.
T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet.
In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on.
Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley .
Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el.
Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door.
Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door .
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door .
Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control(s) or remote control transmitter(s). A moving garage door could injure or kill someone under it.
ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door .
ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex.
Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2).
3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice.
Index Access Door/Outside Quick Release Accessory .........................................................................................................31, 34 Electrical Safety W arnings .............................................................
TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3.
デバイスChamberlain 2000SDの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chamberlain 2000SDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChamberlain 2000SDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chamberlain 2000SDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chamberlain 2000SDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chamberlain 2000SDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChamberlain 2000SDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chamberlain 2000SDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChamberlain 2000SDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。