Chamberlainメーカー2500Dの使用説明書/サービス説明書
ページ先へ移動 of 36
Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless The Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation.
2 Introduction 2-5 Safety symbol review and signal word review ............2 Preparing your garage door ........................................3 T ools ............................................................................3 Planning ...........
3 Preparing your garage door Before you begin: • Disable locks. • Remove any ropes connected to garage door . • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown.
Sa f et y R eversin g Sensor Hori z ontal and vertical rein f orcement is needed f or li g htwei g ht g ara g e doors ( f iber g lass, steel, aluminum, door with g lass panels, etc . ) . See pa g e 2 0 f or details . Header Wall Sa f et y R eversin g Sensor Support bracket & f astenin g hardware is re q uired .
5 Strai g ht Door Arm Section Curved Door Arm Section Header Bracket U P C E I L IN G M O U N T O N L Y 2 - Conductor Bell Wire White & White/ R ed Sa f et y Labels and Literature R emote Control .
ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Align rail and styrofoam over sprocket.
ASSEMBL Y STEP 3 Attach the Belt Cap Retainer • Position the belt cap retainer over the opener sprocket so the two holes in cap align with the two holes in mounting plate. Attach with #8x3/8" hex screws provided. Y ou have now finished assembling your garage door opener .
8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door .
9 ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall above door , as shown. If headroom clearance is minimal, you can install the header bracket on the ceiling.
10 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.
Header Bracket Belt Pulley Bracket Opener Carton or Temporary Support Header Wall Garage Door Clevis Pin 5/16"x2-3/4" Ring Fastener Torsion Spring Rail Clevis Pin 5/16"x2-3/4" Ring.
12 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail.
13 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Y ours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires.
15 INST ALLA TION STEP 7 Install the Lights and Lens Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket.
INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
17 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install .
18 DOOR TRACK MOUNT (RIGHT SIDE) I ndicator L ig h t L ens L ip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) I ndicator L ig h t Sensor Bracket L ens E xtension Bracket (.
19 I nvisi b le L ig h t Beam Protection A rea Sensor Sensor Bell Wire Bell Wire Finished Ceiling Q uick-Connect Terminals Strip w ire 7 /16" 7 /16" Sensor Connections Connect Wire to Q uick.
20 INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel.
21 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door , in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.
INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley .
ALL ONE-PIECE DOORS 1. Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • Make sure the garage door is fully closed. Connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin.
4. Open and close the door with the remote control or door control 2 or 3 times. • If the door does not stop in the desired UP (open) position or reverses before the door stops at the DOWN (close) position, proceed to Adjustment Step 2 Setting the Force.
ADJUSTMENT STEP 2 Setting the Force The force setting button is located on the back panel of the motor unit. The force setting measures the amount of force required to open and close the door . 1. Locate the orange button on the back panel of unit (Figure 1) .
ADJUSTMENT STEP 3 T est the Safety Reversal System TEST • With the door fully open, place a 1-1/2" board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction.
OPERA TION 27 Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory programmed to a matching code which changes with each use, randomly accessing over 100 billion new codes.
28 Using the W all-Mounted Door Control THE MOTION DETECTING DOOR CONTROL Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening.
29 CARE OF YOUR OPENER MAINTENANCE SCHEDULE Once a Month • Manually operate door . If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens & closes fully . Adjust limits and/or force if necessary .
30 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only .
*3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers.
1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Control Panel.
7 10 11 6 5 N O TIC E U P C E I L I N G M O U N T O N L Y 8 1 4 2 3 9 12 L O C K L IG H T 2 1 5 6 3 7 8 4 Rail Assembly Parts Installation Parts 33 KEY P ART NO.
Motor Unit Assembly Parts 34 2 3 4 5 6 7 8 9 10 11 12 1 KEY P ART NO. NO. DESCRIPTION 1 41C76 Belt cap and sprocket 2 41B4245-1 Line cord 3 41B4375-3 T erminal block w/screws 4 41C5317-1 Wire harness (logic) 41C5839 High voltage wire harness 41B5806-1 DC motor wire harness 41C5418 Light socket wire harness 5 41D605-1 Motor 80kg/100kg KEY P ART NO.
35 LOCK LIGHT C LO SE D O P E N ACCESSORIES 974LM 970LM 995LM 2778BD 41A5281 1702LM Outside Quick Release: Required for a garage with NO access door . 8 Foot Complete Rail: T o allow an 8 foot door to open fully .
© 2004, The Chamberlain Group, Inc. 1 14A2933B All Rights Reserved Printed in Mexico LIFTMASTER SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SEVEN DA YS A WEEK.
デバイスChamberlain 2500Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chamberlain 2500Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChamberlain 2500Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chamberlain 2500Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chamberlain 2500Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chamberlain 2500Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChamberlain 2500Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chamberlain 2500Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChamberlain 2500Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
