ChamberlainメーカーATS 2113Xの使用説明書/サービス説明書
ページ先へ移動 of 32
Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation.
2 Introduction 2-5 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning ............
3 T o prevent damage to garage door and opener: • AL W A YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage.
Safety Re versing Sensor Horizontal and vertical reinforcement is needed for lightw eight garage doors (fiberglass, steel, aluminum, door with glass panels , etc.). See page 18 for details . Suppor t brac ket & fastening hardw are is required. See page 1 1.
5 Straight Door Arm Door Bracket Plate Door Bracket Safety Labels and Literature "C" Wrap (2) 2 -Conductor Bell Wire White & White/Red Curved Door Arm Rail Styrofoam Chain Pulley Bracket.
6 ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Place the opener on packing material to protect the cover . • Remove the (2) 5/16"-18x1/2" washered bolts mounted in the top of the motor unit.
7 ASSEMBL Y STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain from twisting. • When the chain is approximately 1/2" (1.
8 INST ALLA TION STEP 1 Determine the Header Bracket Location 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door .
9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.
10 Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Chain Pulley Bracket Temporary Support Header Wall Garage Door Rail Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Cha.
11 INST ALLA TION STEP 4 Position the Opener SECTIONAL DOOR ONL Y A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 laid flat on the top section beneath the rail.
12 Drywall Anchors Insulated Staples Screw 6ABx1-1/2" Lighted Door Control Button HARDW ARE SHOWN ACTUAL SIZE T o prevent possible SERIOUS INJUR Y or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires.
13 INST ALLA TION STEP 7 Install the Light • Install a 75 watt maximum light bulb in the socket. The light will turn O N and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFF . • If the bulb burns out prematurely due to vibration, replace with a “Garage Door Opener” bulb.
14 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
15 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install .
16 Inside Garage Wall “C” Shaped Wrap Mounting Bracket with Square Holes 1/4-20x1/2" Carriage Bolts 1/4"-20 Lock N uts Drill 3/8" Holes Garage Door Track Figure 3 Garage DOOR Track .
17 Hex Bolt 1/4-20 x 1-1/2" "C" Wrap Sensor with Wire Wing N ut Indicator Light Figure 6 Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals Bell Wire Be.
If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2. INST ALLA TION STEP 11 Fasten the Door Bracket A horizontal brace should be long enough to be secured to 2 vertical supports.
19 INST ALLA TION STEP 12 Connect Door Arm to T rolley SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from the door) about 2" (5 cm) as shown in Figures 1, 2 and 3.
20 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle.
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction.
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested every month. • If one control (for ce or travel limits) is adjusted, the other control may also need adjustment.
OPERA TION Using Y our Garage Door Opener Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. Activate your opener with any of the following: • The hand-held Remote Control: Hold the large push button down until the door starts to move.
24 T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push bar . The lockout feature prevents the trolley from reconnecting automatically .
25 Having a Problem? 1. The opener doesn’t operate from either the Door Control or the remote control: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn’t light, check the fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.
26 The 300 Series remote control works only with door openers and light controls having a purple “Learn” button. Programming instructions are described and illustrated below . The additional push buttons can also activate other garage door openers and/or light controls.
27 1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.
28 Multi-Function Door Control (Optional) OPERA TION OF THE MUL TI-FUNCTION DOOR CONTROL Press the push button to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it’s opening. Light feature Press the Light button to turn the opener light on or off.
6 UP CEILING MOUNT ONL Y 10 1 N O TIC E 3 5 4 9 8 11 12 2 7 29 2 1 3 4 5 Installation Parts REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A2780 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 CD1008 8 Foot (2.
30 Motor Unit Assembly Parts 9 7 12 13 14 15 18 4 8 11 17 10 16 3 5 6 18 15 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 1 2 KEY P ART NO. NO. DESCRIPTION 1 41C5069 Rail support bracket assembly kit 2 41B4569 Pulley (Chain) 3 41A5668 Gear and sprocket assembly .
31 ACCESSORIES LOCK LIGHT 370LM CD1008 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot (2.44 m) Complete Rail: T o allow an 8 foot (2.
© 2006, The Chamberlain Group, Inc. 1 14A3155D All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SIX DA YS A WEEK. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Std.
デバイスChamberlain ATS 2113Xの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chamberlain ATS 2113Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChamberlain ATS 2113Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chamberlain ATS 2113Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chamberlain ATS 2113Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chamberlain ATS 2113Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChamberlain ATS 2113Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chamberlain ATS 2113Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChamberlain ATS 2113Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
