ChamberlainメーカーCR550の使用説明書/サービス説明書
ページ先へ移動 of 16
CR550 Rolling Garage Door Opener Installation and Operating Instructions www .chamberlainanz.com Owners Copy: Please keep these instructions for future reference This manual contains IMPORT ANT SAFETY.
1 CONTENTS P AGE SAFETY INSTRUCTIONS . . . . . . . .1 CART ON INVENT ORY . . . . . . . . . .2 TOOLS REQUIRED . . . . . . . . . . . .2 DOOR REQUIREMENTS . . . . . . . .2 PREP ARE & TEST THE DOOR . .3-4 INST ALLA TION . . . . . . . . . . . . . .5-6 CONNECT ELECTRIC POWER .
2 1. Instruction manual (this document) 2. W arning and risk of entrapment labels 3. Hardware bag 4. Release handle, cord and risk of entrapment card 5. 3 Channel mini transmitter (2) 6. W all or visor mounted transmitter 7. Stop collar 8 . Clamp bracket and plate 9.
TESTING THE DOOR Complete the following test to ensure your door is well balanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door . • Lift the door to about halfway and then release it. The door should remain suspended entirely by its spring.
4 PREP ARING THE OPENER 7 For left hand side installations the wire jumper should be removed . For right hand side installations the wire jumper should be in place (factory installed).
5 INST ALLA TION STEPS 9 FOR RIGHT HAND INST ALLA TIONS • Ensure that the opener position jumper (wire connector) is installed (refer Section 7). • Place the opener in manual release mode (refer Section 1 1). • Open the roller door fully . For safety , tie a rope around the door (as shown).
1 0 • Thread one end of the rope through the hole in the top of the red handle so “NOTICE” reads right side up as shown. • Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. • Thread the other end of the rope through the loop of the manual release cable.
T ravel limits regulate the points at which the door will stop when moving UP or DOWN. During the set up procedure, the motor will run and operate the door . T he opener must be fully installed on the door and all installation steps completed before proceeding.
T he force, as measured on the closing edge of the door , should not exceed 400 N (40 kg). If the closing force is measured to more than 400 N, The Protector System TM (IR Beams) must be installed (refer section 16). The force setting regulates the amount of power required to open and close the door .
NOTE: This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400 N (40 kgf). After the opener has been installed and adjusted, the Protector System™ (IR Beams) accessory can be installed.
10 ADDING transmitters using the learn button • Press and hold down the transmitter button you wish to program to the opener . • The orange LED will flash continuously to indicate it is receiving signal from the transmitter . • Press and release the learn button on the opener .
Wireless Keypad 8747AML Using the (purple) learn button: 1. Press and release the (purple) learn button (1) on the opener (the orange LED will light). 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad (2), then press and hold the ENTER button.
12 1 2 L O C K L I G H T 1.Multifunction control panel Connect white/red wire to the red “wired wall control” quick connect terminal and the white wire to the white “wired wall control” quick connect terminal.
TROUBLESHOOTING 1.The opener doesn't operate from either the GREEN start button or the transmitters: • Does the opener have electric power? Plug a lamp into t he outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1.
14 O PERA TION OF YOUR OPENER Y our opener can be activated by any of the following devices: • The GREEN start button Hold the button down until door starts to move. • The wall control, outside keyswitch or keyless e ntry system (if you have installed any of these accessories).
15 © 2012 The Chamberlain Group, Inc 1 14B4542B TM T rademark of The Chamberlain Group, Inc. ® Registered Trademark of The Chamberlain Group, Inc. Chamberlain Limited W arranty , we may , subject to your other rights and remedies as a consumer , charge you a fee to repair , replace and/or return the Unit to you.
デバイスChamberlain CR550の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chamberlain CR550をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChamberlain CR550の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chamberlain CR550の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chamberlain CR550で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chamberlain CR550を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChamberlain CR550の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chamberlain CR550に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChamberlain CR550デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。