ChauvetメーカーDMX512の使用説明書/サービス説明書
ページ先へ移動 of 12
SX Gobo™ Snapshot Ok on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle USER MANUAL Chauvet, 3000 N 2 9 th Ct, Hollywood, FL 33020 U.S.A. (800) 762-1084 – (954 ) 929-1115 FAX (954) 929-5560 www.
T ABLE OF C ONTENTS 1. BEFORE YOU BEGIN ............................................................................................................ ................... . 3 W HAT IS INCLUDED ............................................................
1. B EFORE Y OU B EGIN What is included ¾ 1 x SX Gobo™ ¾ EHJ 24V 250W Lamp ¾ 7 Replaceable Gobos ¾ Warranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. x Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
2. I NTRODUCTION Features x High-output rotating gobo projector x Interchangeable rotating color/gobos 6 metal gobos with 5 dichroic colors + white x Dual spring clips for a single dichroic color x Ad.
3. S ETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. An 800W halogen lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement.
Lamp Alignment How-To Lamp alignment screws Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is refered to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector.
Figure A Figure B Figure C Replacing Gobos 1) Open the top cover by removing the six screws indicated in figure A. 2) Remove the retaining spring using a flathead screwdriver (figure B). 3) Remove the gobo and replace with a new gobo. Note: The black side of the g obo should be facing the lamp.
Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for v entilation. RIGGING Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp.
General Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check fan thermal switch reset 9 Beam is very dim or not bright Clean op.
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A. ) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Pre ss 4) Fax: (954) 929-5560 - (Attention: Service) Website: http://www.chauvetlighting.com 5.
Claims Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon recei pt of merchandise. It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping.
デバイスChauvet DMX512の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chauvet DMX512をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChauvet DMX512の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chauvet DMX512の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chauvet DMX512で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chauvet DMX512を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChauvet DMX512の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chauvet DMX512に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChauvet DMX512デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。