ChauvetメーカーDMX512の使用説明書/サービス説明書
ページ先へ移動 of 19
Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle MiN™ S pot USER MANUAL Chauvet, 3000 N 2 9 th Ct, Hollywood, FL 3 3020 U.S.A. (800) 762-1084 – (954 ) 929-1115 FAX (954) 929-5560 www.
T ABLE OF C ONTENTS MiN™ Spot ..................................................................................................................... ................................ 1 USER MA NUAL .....................................................
1. B EFORE Y OU B EGIN What is included ¾ 1 x MiN™ Spot ¾ Power Cord ¾ Warranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Safety Instructions Please read these instructions carefully, it includes important information about the installation, usage and maintenance of this product. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
2. I NTRODUCTION Features CONTROL FEATURES • 5 or 13-channel DMX-512 LED moving yoke • Pan: 540 o / tilt: 270 o • RGB color mixing • Gobo wheel 9 gobos + open Gobo wheel spin effect • Variab.
DMX Channel Summary - 5 Channel Mode C HANNEL F UNCTION 1 Pan 2 Tilt 3 Shutter 4 Color Macro 5 Gobo Product Overview Projector Head Lens Focus LED Readout Control Panel DMX In DMX Out IEC Power Connec.
3. S ETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement The fuse is located inside this With a flat head screwdriver wedge the fuse holder out of its housing. Remove the damaged fuse from its holder and replace with exact same type fuse.
CABLE CONNECTORS CABLE CONNECTORS Cabling must have a male XLR connector on one end and a female XLR connector on the othe r end. Cabling must have a male XLR connector on one end and a female XLR connector on the othe r end. 2 1 3 OUTPUT Termination reduces signal er rors.
Master/Slave Fixture Linking 1. Connect the (male) 3 pin connector side of the DM X cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixtur e consisting of a (male) 3 pin connector.
4. O PERATING I NSTRUCTIONS Navigating the Control Panel Access control panel functions using the four pa nel buttons located directly underneath the LCD Display.
Menu Map MiN™ Spot User Manual 11 2008-07-15/12 :39.
User Configurations TO SET THE PAN TO INVERTING OR NON-INVERTIN G: 1) Press the Mode button until it shows or 2) Use the Up/Down buttons to set to the desired inversion, press enter to confirm.
Stand-Alone Mode ( Auto Mode): This mode allows a single unit to run to a factory installed program in one of two speeds. 1) To set the fixture in auto mode Fast , select .
DMX Channel Values (13 Channel) C HA NNE L V ALU E F UNCTION 1 000 Ù 255 Pan 2 000 Ù 255 Pan Fine 3 000 Ù 255 Tilt 4 000 Ù 255 Tilt Fine 5 000 Ù 255 V ector Speed: (Normal → Slow) 6 000 Ù 007 .
DMX Channel Values (5 Channel) C HANNEL V AL UE F UNCTION 1 000 Ù 255 Pan 2 000 Ù 255 Tilt 3 000 Ù 007 008 Ù 134 135 Ù 239 240 Ù 255 Dimmer/Strobe Closed 100-0% Strobe (slow → Fast) Open 4 000.
Troubleshooting Symptom Solution(s) Applies to Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check f an thermal switch reset 9 Beam is very dim or not bright Clean optical s.
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A. ) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Pre ss 4) Fax: (954) 929-5560 - (Att ention: Service) Website: http://www.chauvetlighting.com 6.
General Maintenance To maintain optimum performance and minimize we ar fixtures should be cleaned frequently. Usage and environment are contributing factors in determi ning frequenc y. As a general rule, fixtures should be cleaned at least twice a month.
MiN™ Spot User Manual 19 2008-07-15/12 :39 Technical Specifications WEIGHT & DIMENSIONS Length......................................................................................................................... .... 6.8 in (173 mm) Width ..
デバイスChauvet DMX512の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chauvet DMX512をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChauvet DMX512の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chauvet DMX512の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chauvet DMX512で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chauvet DMX512を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChauvet DMX512の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chauvet DMX512に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChauvet DMX512デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。