ChauvetメーカーVue IIの使用説明書/サービス説明書
ページ先へ移動 of 16
Chauvet, 3000 N 2 9 th Ct, Hollywood, FL 3 3020 U.S.A. (800) 762-1084 – (954 ) 929-1115 FAX (954) 929-5560 www.chauvetlightin g.com V ue™ II Snapshot Ok on Dimmer Outdoor OK Sound Activated DMX512.
T ABLE OF C ONTENTS 1. BEFORE YOU BEGIN ............................................................................................................................... .3 W HAT IS INCLUDED ..............................................................
1. B EFORE Y OU B EGIN What is included ¾ 1 x Vue™ II ¾ Power Cord ¾ W arranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that the y also receive this instruction booklet.
2. I NTRODUCTION Features • 6-channel DMX-512 LED moon flower • Blackout/static/dimmer/strobe • Individual control of red, green and blue LEDs • Built-in automated programs via master/slave or.
Product Overview Tilt Adjustment Knob Hanging Bracket Power LED Microphone Signal/Sound Indicator LED Power Output Connector Dipswitches DMX Output Connector DMX Input Connector Sound Sensitiv ity Kno.
3. S ETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement The fuse is located inside this compartment. Remove using a flat head screwdriver. With a flat head screwdriver wedge the fuse holder out of its h ousing.
CABLE CONNECTORS This drawing prov ides a general illustration of the DMX Input/Output panel of a lighting fixture. U X Controller niversal DM Continue t he link Cabling must have a male XLR connector on one end and a female XLR connector on the othe r end.
Often, the se tup for Master-S lave and Standalone op eration requires at the first f ixture i n t he chain be itialize d for this pur pose via ei ther ttings in the co ntrol panel or DIP- th in s e switches. Secondarily, the f ixture s that follow may also requir e a slave setting.
4. O PERATING I NSTRUCTIONS Operation Stand-Alone Mode (Sound-Active, Au to Mode, Strobe Mode, All On): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode. 1) Set dipswitches position to Sound-Active or Auto Mode.
DMX Mode This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page 15. 1) Set dipswitches 1-9 to the desired DMX addr ess. For help setting the address, see the “SETTING THE STARTING ADD RESS” section on the next page.
SETTING THE STARTING ADDRESS This DMX mode enables the use of a uni versal DMX controller device. Each fixture requires a "sta rt address" from 1 to 512. A fixture requiring one or mo re chan nels for control begins to read the data on the channel indicated by the start address.
DMX QUICK R EFERENCE CHART DMX Address Quick Reference Chart Dip Switch Position DMX DIP SWITCH SET #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0=OFF #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1=ON #7 0 0 1 1 0 0 1 1 .
General Troubleshooting Applies to Symptom Solution(s) Light s Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check f an thermal switch reset 9 Beam is very dim or not bright Clean .
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A. ) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Pre ss 4) Fax: (954) 929-5560 - (Att ention: Service) Website: http://www.chauvetlighting.com 5.
Returns Proced ure Returned merchandise must be sent prepaid and in t he original packing, call tags will not be issued. Package must be clearly labeled with a Return Merc handise Author ization Number (RA #). Products returned without an RA # will be refused.
デバイスChauvet Vue IIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chauvet Vue IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChauvet Vue IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chauvet Vue IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chauvet Vue IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chauvet Vue IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChauvet Vue IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chauvet Vue IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChauvet Vue IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。