CiscoメーカーEngine 611の使用説明書/サービス説明書
ページ先へ移動 of 16
Corporate Headquarters: © 20 05 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Installing Hard Disk Drives in the Cisco Wide Area Ap.
2 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Safety Overview Protecting Against Electrostatic Discharge Static electricit y can harm delicate componen ts insi de the de vice.
3 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Introduction Introduction The W AE-611 supports two 1-inch (2 .54-cm) slim 3.5-inch (8.89-cm) lo w voltage dif ferential (L VD) hard disk dri ves. The W AE-611 requires SCSI h ard disk dri ves.
4 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Removing the Bezel and Cover Removing the Bezel and Cover War ni ng Before working on a sy stem that has an on/off switch, tu rn OFF the power and unplug the power cord.
5 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing the Beze l and Cover Figur e 2 Removing the Co ver Step 5 Slide the cov er back. Lift it up and of f the device. Caution For proper cool ing and airflo w , replace the cov er before turning on the de vice.
6 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Assigning SCSI IDs Figur e 3 Location of Dr ive Ba ys Behind the Bezel Assigning SCSI IDs When you install or replace one or more of the SCSI disk dri ves in a W AE-611, you must assign a SCSI ID to each disk dri ve.
7 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve • Seagate disks hav e two sets of jumpers.
8 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Removing and Replac ing a SCSI Hard Disk Drive Note All hard disk dri ves that you use in the W AE should ha ve the same throughput speed rating.
9 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve Figure 5 Disk Dr ive Or ienta t ion During Installation Step 11 Connect the power and SCSI cables to the dri ve. If you disconnected the IDE cable to the CD-R OM, reconnect it.
10 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Replacing the Cover a nd Beze l and Completing the Installation Replacing the Cover and Bezel and Completing the Installation War ni ng This unit is intend ed for installation in restricted acc ess areas.
11 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Documentation Step 4 Connect all external cables and the po wer cord to the device, and then pl ug the po wer cord into a properly grounded electrical out let.
12 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance In an emer gency , you can also reach PSIR T by telephone: • 1 877 228-73.
13 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce Submitting a Service Request Using the online T A C Se rvice Request T ool is the fast e st way to open S3 and S4 service requests.
14 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance Definitions of Service Request Severity T o ensure that a ll service req uests are r eported in a standard format, Cisco has established se verity definitions.
15 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce This document is to be used in con junction with th e documents listed i n the “Related Documentation” section. © 2006 Cisc o Systems, Inc.
16 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance.
デバイスCisco Engine 611の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cisco Engine 611をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Engine 611の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Engine 611の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Engine 611で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Engine 611を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Engine 611の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Engine 611に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Engine 611デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
