Cisco Systemsメーカー69561の使用説明書/サービス説明書
ページ先へ移動 of 18
Wireless LAN Controller (WLC) FAQ Document ID: 69561 Questions Introduction General FAQ Troubleshoot FAQ NetPro Discussion Forums − Featured Conversations Related Information Introduction This document provides information on the most frequently asked questions (FAQ) about the Cisco Wireless LAN (WLAN) Controllers (WLCs).
Bootloader Version............................... 4.0.217.0 Build Type....................................... DATA + WPS Compact Flash Size............................... 256 MB In order to view the active boot image, use the command show boot (Cisco Controller) > show boot Primary Boot Image.
You must reboot the WLC in order for the new software to take effect, so there is a period of network downtime. Be sure to schedule a maintenance window for the upgrade. Q. Can a Cisco IOS Software−based access point (AP) that has been converted to lightweight mode register with Cisco 4100 Series WLCs? A.
mobility group. You can configure up to 12 Wireless Services Module (WiSM) blades in one mobility group. Therefore, up to a maximum of 3600 access points (APs) are supported in a single mobility group. Q. How does DHCP work with the WLC? A. The WLC acts as a DHCP relay device.
From the Wireless Downloads page, click on Wireless LAN Controller and select the controller platform for which you need the MIBs. 1. The Software Download page for the controller appears. This page contains all the files for the WLC including the MIBs.
Q. Which lightweight access points (LAPs) do the 4100 Series Controllers support? A. Only the Airespace 1200, 1250, the Cisco 1000 Series, and the Cisco 1500 Series LAPs work with the earlier 4100 Series Controllers. Q. I have a Cisco Adaptive Security Appliance (ASA) device.
A. This is due to Cisco bug ID CSCsh58468 ( registered customers only ) . As of the latest controller version 4.0.206.0, a user can enter only 31 characters.
Enable broadcast service set identifier (SSID) per WLANWith broadcast SSID enabled, the WLAN/SSID information is sent in the beacons. This also helps clients that perform passive scanning (those that do not transmit probe request) as well as clients configured without an SSID to associate with the controller through this WLAN.
Q. Can the Wireless LAN Controller (WLC) send email notifications to the administrator when a critical event occurs? A. The WLC does not send email, but it can send traps to the Network Management System (NMS) stations, such as HP OpenView (HPOV). HPOV can perform things such as running scripts to send email on receipt of particular traps.
configuration to the backup controller off the production network. After the configuration is copied to the backup controller, you need to change the hostname, IP addressing information, RADIUS shared secret keys (possibly) and Mobility group lists information.
Q. Is it possible to set a limit to the number of clients that connect to the access point (AP) on the AP itself? A. In general, there is no way on the AP to limit the number of clients that connect. The clients actually load balance between APs once they exceed the profile threshold value, which by default is 12 users.
(WLCM) or Wireless Services Module (WiSM), you should be able to access the controller from the WCS and create a new admin user without logging into the controller itself.
Bridge AP to Normal AP. Q. I recently set up the 4402 Wireless LAN Controller (WLC) to manage the new Cisco lightweight access points (LAPs). I run PIX 501 version 6.
Q. Does the Cisco Unified Wireless solution support redundant WLCs in the DMZ for guest tunneling? A. Presently there is no support for redundant WLCs in the DMZ for guest tunneling. This is why the client does not automatically connect to the other controller in the DMZ.
MAC address. Q. No traps are generated by the WLC for Ad−Hoc rogues and the SNMP debugs on the WLC do not show any traps from the WLC for Ad−Hoc even though the WLC GUI reported the Ad−Hoc rogues. The WLC runs firmware version 3.2.116.21. Why does this happen? A.
AP1 can hear the client that communicates to AP2, but AP2 cannot be heard. Therefore, it cannot be validated as a neighbor. ♦ The workaround is to manually set the APs to known internal on the WLC and/or WCS. Complete these steps on the controller in order to manually set the APs to known internal: Go to the WLC GUI and choose Wireless .
This command will replace the 1.1.1.1 virtual interface address, which shows up itself as the DHCP server, with the actual DHCP server IP address that you defined on the interface or in the override option of the WLAN.
Wireless − Mobility: WLAN Radio Standards Wireless − Mobility: Security and Network Management Wireless − Mobility: Getting Started with Wireless Wireless − Mobility: General Related Informati.
デバイスCisco Systems 69561の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cisco Systems 69561をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems 69561の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems 69561の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems 69561で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems 69561を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems 69561の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems 69561に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems 69561デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。