Cisco SystemsメーカーCisco 10000 ESRの使用説明書/サービス説明書
ページ先へ移動 of 22
Corporate Headquarters: Cisco Systems, In c., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 20 00. C isco Systems, Inc. All rights reserved.
Product Description 2 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Product Description The A C PEM provides po wer con version directly from the f acility V A C input po wer (100 V A C to 240 V A C) to the –48V VDC used internally by the system (see Figure 1).
3 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Prerequisites and Pr eparation Prerequisites and Preparation Before you perform an y of the procedures in this guide, Cisco recommends.
Installation Guidelines 4 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 War ni ng This warning symbol me ans danger . Y ou are in a si tuation that could cause bodily injury .
5 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Adding or Replacing an AC PEM This section describes how to add or replace an A C PEM in the Cisco 10000 chassis.
Adding or Replacing an A C PEM 6 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Remov e the cove r by lifti ng it up slightly an d then pulling it to ward you (Figure 3).
7 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Installing a Second AC PEM Use the follo wing procedure to install a second A C PEM in the bottom po wer bay for redundanc y .
Adding or Replacing an A C PEM 8 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Loosen the capti ve screws to remo ve the blank cov er from the bottom po wer bay (Figure 5).
9 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 3 Install the ne w AC PEM all the w a y into the po wer bay to ensure a secure connection to the backplane, and then tighten the captive scre ws (Figure 6).
Adding or Replacing an A C PEM 10 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 4 Connect the po wer cord from the PEM to your po wer cord that connects to the facili ty V A C input. Step 5 Set the A C power cord connec tors in a cord strain relief (canoe) to prev ent them from accidently disco n necting (Figu re 7).
11 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 7 Set the po wer switch to the on (|) position ( Figure 8). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figure 8 Setting the A C Po wer Switc h to the On P osition Step 8 Replace the front cover .
Adding or Replacing an A C PEM 12 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Replacing an AC PEM Use the following procedure to replace an A C PEM. Note The illustrations in this guide sho w how to replace the A C PEM from the bottom po wer bay .
13 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 2 Po wer off the PEM you are replacing (Figur e 10). Caution Do not po wer off both A C PEMs in a redundant system or the system shuts do wn and all data traff ic stops.
Adding or Replacing an A C PEM 14 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 3 Remov e the PEM power cable from its cano e and disconnect it from the A C input power cabl e (Figure 11).
15 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 4 Loosen the captiv e screws on the PEM and remove the PEM from the chassis using the handle on the faceplate (Figure 12).
Adding or Replacing an A C PEM 16 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 5 Install the ne w PEM all the way into the po wer bay to ensure a good connection to the backplane, and tighten the ca ptiv e screws on the PEM (Figur e 13).
17 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 6 Connect the po wer cord from the PEM to the po wer cord that connects to the facili ty V A C input. Step 7 Set the A C power cord connec tors in a cord strain relief (canoe) to prev ent them from accidently di sconnecting (Figur e 14).
Adding or Replacing an A C PEM 18 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 9 Set the po wer switch to the on (|) position ( Figure 15). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 15 Set ting the A C Po wer Switc h to the On P osition Step 10 Replace the front cover .
19 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Troubleshooting the Installation T able 1 contains troub leshooting informatio n for the A C PEM: T ab.
FCC Class A Compliance 20 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 FCC Class A Compliance This equipment has been tested an d found to comply with the limi ts for a Class A digital de vice, pursuant to part 15 of the FCC rules.
21 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Cisco Connection Online A vailable 2 4 hours a day , 7 days a week, CCO pro vides a wealth of standard and v alue-added services to Ci sco customers and b usiness partners.
Documentation CD-ROM 22 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Documentation CD-ROM Cisco documentation and additi onal lite rature are av ailable in a CD -R OM package, which ships with your produ ct. The Documentation CD- ROM, a member of the Cisco Connection F amily , is updated monthly .
デバイスCisco Systems Cisco 10000 ESRの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cisco Systems Cisco 10000 ESRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems Cisco 10000 ESRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems Cisco 10000 ESRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems Cisco 10000 ESRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems Cisco 10000 ESRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems Cisco 10000 ESRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems Cisco 10000 ESRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems Cisco 10000 ESRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
