Cisco SystemsメーカーCX-FEIP-1FX=の使用説明書/サービス説明書
ページ先へ移動 of 42
1 Customer Order Number: Cisco Systems, Inc. All rights reser ved. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Systems, Inc. Corporate Headquarters Copyright © 1995–2002 Documentation P.
2 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Document Contents Document Contents This publication includes the following sections: • If Y ou Need More Information • .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 3 Installation Prerequisites • T o obtain information about documentation, refer to the following: — W orld W ide W eb on page 40 — Documentation CD-R OM on page 40 — Ordering Documentation on page 40 — Documentation Feedback on page 40 — Cisco.
4 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Installation Prerequisites Each FEIP is a fixed configuration; therefore, indi vidual port adapters are not a vailable as spare parts and are not field-replaceable or remov able.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 5 Safety Guidelines • Do not perform any action that creates a potential hazard or makes the equipment unsafe. • Carefully examine your work area for possible hazards such as moist floors, ungrounded po wer extension cables, and missing safety grounds.
6 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Installation Prerequisites Guidelines f or Interf ace Processor Installation and Remov al This section describes mechanical .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 7 Guidelines for Interface Processor Installation and Removal Figure 1 Ejector Lever s/Captive Installation Screws on the FEIP (.
8 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Installation Prerequisites Microcode Ov er vie w The FEIP microcode (firmware) is an image that provides card-specific softw are instructions.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 9 IEEE 802.3u 100BaseT Specifications • 100B ASE-T4—100B ASE-T , half and full duplex o ver Cate gory 3, 4, or 5 UTP or shielded twisted-pair (STP) cabling with four pairs; also called 4T+ or T2, which is 2-pair UTP ov er Category 3 cable.
10 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Installation Prerequisites Figure 2 Maximum Segment and Netw ork Lengths—100B ASE-FX and 100B ASE-TX What Is the Cisco 7000 Series? The Cisco 7000 series includes the Cisco 7000 and Cisco 7010 routers.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 11 What Is the Cisco 7000 Series? Figure 3 Cisco 7000 (Interface Processor End) In the 5-slot Cisco 7010 (Figure 4), slots 0 through 2) are for interface processors including the FEIP .
12 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Installation Prerequisites What Is the Cisco 7500 Series? The Cisco 7500 series includes the Cisco 7505, Cisco 7507, and Cisco 7513 routers. The FEIP operates in the Cisco 7500 series routers.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 13 What Is the Cisco 7500 Series? In the Cisco 7507 (see Figure 6), slots 0 and 1 and 4 through 6 are for interface processors including the FEIP . Figure 6 Cisco 7507 (Interface Processor End) ENABLE ENABLE EJECT SLOT 0 SLOT 1 NORMAL CPU HALT RESET AUX.
14 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Installation Prerequisites In the Cisco 7513 (see Figure 7), slots 0 through 5 and 8 through 12 are for interface processors including the FEIP . Figure 7 Cisco 7513 (Interface Processor End) ENABLE ENABLE H5268 EJECT SLOT 0 SLOT 1 NORMAL CPU HALT RESET AUX.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 15 What Is the FEIP? What Is the FEIP? The FEIP provides up to tw o 100-Mbps, IEEE 802.
16 F ast Ethernet Interface Processor (FEIP) Installation and Configuration What Is the FEIP? Note Each FEIP is a fixed configuration; therefore, indi vidual port adapters are not a vailable as spare parts and are not field-replaceable or remov able.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 17 FEIP Receptacles, Cables, and Pinouts Follo wing are the three status LEDs and an explanation of what each indicates: • MII—On when the MII port is selected as the activ e port by the controller .
18 F ast Ethernet Interface Processor (FEIP) Installation and Configuration What Is the FEIP? The RJ-45 connection does not require an external transcei ver . The MII connection requires an external physical sublayer (PHY) and an e xternal transceiv er .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 19 FEIP Receptacles, Cables, and Pinouts Depending on your RJ-45 interface cabling requirements, use the pinouts in Figure 13 and Figure 14.
20 F ast Ethernet Interface Processor (FEIP) Installation and Configuration What Is the FEIP? Depending on the type of media you use between the MII connection on the port adapter and your switch or .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 21 FEIP Installation FEIP Installation The following sections describe the procedures for remo ving or installing an FEIP in the Cisco 7000 series or Cisco 7500 series routers.
22 F ast Ethernet Interface Processor (FEIP) Installation and Configuration FEIP Installation Removing an FEIP Y ou need not shut down the interf ace or the system power when remo ving an FEIP or interface processor .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 23 Installing an FEIP T o remov e an FEIP or interface processor , follo w these steps: Step 1 Attach an ESD-prev enti ve wrist strap between you and an y unpainted chassis surface.
24 F ast Ethernet Interface Processor (FEIP) Installation and Configuration FEIP Installation Step 2 Hold the FEIP handle with one hand and place your other hand under the carrier to support the FEIP and guide it into the slot. (See Figure 18.) A void touching the card or any connector pins.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 25 Attaching Fast Ethernet Interface Cables Connect RJ-45, SC (FEIP-1FX or -2FX), or MII cables as follows: Step 1 If you hav e .
26 F ast Ethernet Interface Processor (FEIP) Installation and Configuration FEIP Installation Figure 20 Connecting MII or SC Cables (FEIP-2FX Shown, Horizontal Orientation) Step 2 For the 100B ASE-TX RJ-45 connections, attach the ferrite bead to the RJ-45 cable (at either end), as shown in Figure 21.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 27 Using LEDs to Check FEIP Status Using LEDs to Chec k FEIP Status The FEIP has four status LEDs on its faceplate that indicate status on each FE port.
28 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Configuring the Fast Ethernet Interfaces* Step 4 If an enabled LED still fails to go on, remov e the FEIP and try installing it in another av ailable interface processor slot.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 29 Selecting Interface Processor Slot, Interface, and Interface Port Numbers Selecting Interf ace Processor Slot, Interf ace, and Interf ace P or t Numbers This section describes ho w to identify interface processor slot, interface, and interface port numbers.
30 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Configuring the Fast Ethernet Interfaces* Configuring Interfaces—Descriptions and Examples This section describes a basic configuration. Press the Return k ey after each step unless otherwise noted.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 31 Configuring Interfaces—Descriptions and Examples FE half-duplex operation is the default. T o change to full-duplex operation, use the following series of commands: Router# configure terminal Enter configuration commands, one per line.
32 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Configuring the Fast Ethernet Interfaces* The RJ-45 connection is the default for FEIP-2TX (or SC for FEIP-2FX).
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 33 Checking the Configuration Using show Commands to Displa y Interf ace Inf ormation T o display information about a specific interface, use the show interfaces command with the interface type and port address in the format show interfaces [ type slot/adapter/port ].
34 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Configuring the Fast Ethernet Interfaces* The show contr ollers cbus command displays information about all of the interf ace processors in your router , including the FEIP .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 35 Checking the Configuration The show version (or sho w hardwar e ) command displays the configuration of the system hardware (the number of each interface processor type installed), the software v ersion, the names and sources of configuration files, and the boot images.
36 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Configuring the Fast Ethernet Interfaces* T o determine which type of interfaces are installed on an FEIP in your system, use the show diag slot command.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 37 Upgrading FEIP Microcode Using the ping Command to V erify Network Connectivity The pack et internet gr oper ( ping ) command.
38 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Upgrading FEIP Microcode T o compare the size of the microcode image and the amount of Flash memory av ailable, you must kno w the size of the new microcode image. The image size is specified in the README file that is included on the floppy disk with the ne w image.
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 39 Upgrading FEIP Microcode Step 4 Use the show flash command to v erify that the microcode has been copied to Flash.
40 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Obtaining Documentation Obtaining Documentation The follo wing sections provide sources for obtaining documentation from Cisco Systems. W orld Wide W eb Y ou can access the most current Cisco documentation on the W orld W ide W eb at the following sites: • http://www .
Fast Ethernet Interface Processor (FEIP) Installation and Configuration 41 Obtaining Technical Assistance Obtaining T echnical Assistance Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample conf igurations from online tools.
42 F ast Ethernet Interface Processor (FEIP) Installation and Configuration Obtaining T ec hnical Assistance http://www .cisco.com/warp/public/687/Directory/DirT A C.
デバイスCisco Systems CX-FEIP-1FX=の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cisco Systems CX-FEIP-1FX=をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems CX-FEIP-1FX=の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems CX-FEIP-1FX=の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems CX-FEIP-1FX=で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems CX-FEIP-1FX=を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems CX-FEIP-1FX=の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems CX-FEIP-1FX=に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems CX-FEIP-1FX=デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。