Cisco SystemsメーカーIGX 8の使用説明書/サービス説明書
ページ先へ移動 of 12
APPENDIX -1 System Specifications A This appendix contains system specifications. General This section provides general system information on the IGX 8. System Capacity: 1 shelf with 8 card slots. Requires 2 dedicated front slot(s) for NPMs. Requires 2 dedicated back slots for SCMs (1 slot with blank plate).
-2 IGX 8 Installation Manual, Release 8.2.0 V oice Cir cuit Suppor t Input A C Po wer Connector: IEC 16 Amp input connector . 6 dif ferent power cords are a v ailable to comply with the standards of individual countries. Po wer cords are 6 feet (about 2 meters) long.
-3 Data Channel Suppor t Sync. Data Interfaces: RS-232C/D, RS-449/422, V .24, X.21, and V .35 with IGX 8 as DCE or DTE. High-Speed Data Rates (HDM): 2.4 Kbps to 1.344 Mbps. Low-Speed Data Rates: 2.4 to 19.2 Kbps per LDM port. Ports per card: LDI: 4 or 8.
-4 IGX 8 Installation Manual, Release 8.2.0 Digital Data Service Interface Ports per card: Four . Electrical Interface: Digital Data System (DDS)—A T&T Pub. 62310, No vember 1987. Interface T ype: DSU or OCU (software selectable). Data Rates: 2.
-5 T1 Interface Line Rate: 1.544 Mbps, ± 50 bps ( ± 200 bps VCO lock range). Line Code: Bipolar AMI or B8ZS. Framing Formats: Fractional T1, adjacent or alternating channels. Minimum of four DS0 channels required. Signal Le vel: DSX-1 compatible. Line Impedance: T erminated = 100 Ohms nominal.
-6 IGX 8 Installation Manual, Release 8.2.0 E1 Interface Line Rate: 2.048 Mbps, ± 50 bps ( ± 200 bps VCO lock range) Line Code: Bipolar AMI or HDB3 Line Impedance: 120 Ohms (balanced) or 75 Ohms (balanced or unbalanced) Minimum Pulse Density: Zero code suppression via HDB3 coding Frame Format: Unframed, 32-channel (G.
-7 T3 Interface Line Rate: 44.736 Mbps ± 20 ppm, asynchronous. Line Code: B3ZS. Clock Source Mode: Internal (Asynchronous). Signal Le vel: DSX-3. Framing Formats: M13 mode, C-bit parity . Alarms Processed: AIS. LOS. Remote Alarm Indication. Loss Of Framing.
-8 IGX 8 Installation Manual, Release 8.2.0 E3 Interface Line Rate: 34.368 Mbps ± 20 ppm, asynchronous. Line Code: HDB3. Clock Source Mode: Internal (Asynchronous). Signal Le vel: ITU-T G.703 Framing Formats: ITU-T G.804, G.832, Alarms Processed: AIS.
-9 Frame Rela y Interface T ype of Service: Permanent V irtual Circuit (PVC). Data Interface: Per ITU-T I.122 and ANSI T1/S1 Standards. Data T ransfer Protocol: LAP-D frame level core functions. Input Data Format: High Le vel Data Link (HDLC) protocol.
-10 IGX 8 Installation Manual, Release 8.2.0 A TM Interface Netw ork Synchr onization T ype of Service: Permanent V irtual Circuit (PVC) Interface T ypes: User-to-Netw ork (UNI) and Network-to-Network (NNI) per ITU I.
-11 Netw ork Management Control Network Control T erminal: StrataV iew Plus workstation and StrataCom software required for graphical display of network status, statistics gathering and display , and automatic do wnloading of software.
-12 IGX 8 Installation Manual, Release 8.2.0.
デバイスCisco Systems IGX 8の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cisco Systems IGX 8をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems IGX 8の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems IGX 8の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems IGX 8で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems IGX 8を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems IGX 8の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems IGX 8に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems IGX 8デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。