Cisco SystemsメーカーPA-2Hの使用説明書/サービス説明書
ページ先へ移動 of 62
170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) 408 526-4000 Fax: 408 526-4100 P A-2H Dual-P or t HSSI P or t.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED.
About This Manual v About This Man ual This chapter explains the objecti v es and organization of the P A-2H Dual-P ort HSSI P ort Adapter Installation and Configuration document and defines the con ventions used to con vey instructions and information.
Cisco Connection Online vi PA-2H Dual-Port HSSI Port Adapter Installation and Configuration • Chapter 2, “Preparing for Installation, ” is a preparatory chapter that describes safety considerations, tools required, and procedures you should perform befor e the actual installation.
About This Manual vii Documentation CD-ROM Note If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or cov ered by a maintenance contract, contact Cisco’ s T echnical Assistance Center (T AC) at 800 553-2447, 408 526-7209, or tac@cisco.
If You Need More Information viii PA-2H Dual-Port HSSI Port Adapter Installation and Configuration — Second-Generation V ersatile Interface Pr ocessor (VIP2) Installation and Configuration (for VIP.
About This Manual ix If You Need More Information • For general information about documentation, refer to the Documentation CD-R OM, the “Cisco Connection Online” section on page vi or call Customer Service at 800 553-6387 or 408 526-7208. Customer Service hours are 5:00 a.
If You Need More Information x PA-2H Dual-Port HSSI Port Adapter Installation and Configuration.
CHAPTER Overview 1-1 1 Ov er vie w This chapter provides physical and functional o verviews of the P A-2H dual-port high-speed serial interface (HSSI) port adapter .
Port Adapter Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 1-2 The HSSI port adapter conforms to B ABT/TC/130 and EIA/TIA-612 and EIA/TIA-613 standards for HSSI.
Overview 1-3 LEDs Note Y ou should replace older P A-2H port adapters with the newer P A-2H Rev . B port adapter . Contact Cisco’ s T echnical Assistance Center (T A C) for replacement details. (For information on the T AC, refer to the “Cisco Connection Online” section on page vi.
Receptacles, Cables, and Pinouts PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 1-4 Receptac les, Cables, and Pinouts This section provides information about the HSSI cables you should use with the HSSI port adapter .
Overview 1-5 HSSI Null Modem Cable HSSI Null Modem Cab le The null modem cable (CAB-HNUL=) can connect two routers directly back to back. The null modem cable is 10-feet (3.048 meters) long. Figure 1-6 shows the null modem cable. The maximum null modem cable length allowed is 50 feet (15.
Receptacles, Cables, and Pinouts PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 1-6.
CHAPTER Preparing for Installation 2-1 2 Prepar ing f or Installation This chapter describes the general equipment, safety , and site preparation requirements for installing the P A-2H dual-port high-speed serial interface (HSSI) port adapters.
Software and Hardware Requirements PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 2-2 Software and Har dware Requirements T able 2-1 lists the minimum Cisco IOS software release required to use the 2H port adapters in supported router platforms.
Preparing for Installation 2-3 Safety Guidelines P A-2H cannot be used with a P A-A1 (Asynchronous T ransfer Mode [A TM]) port adapter installed in the adjacent port adapter slot of your VIP2 or Catalyst RSM/VIP2. All other port adapters are compatible with P A-2H when installed in the adjacent port adapter slot of your VIP2 or Catalyst RSM/VIP2.
Safety Guidelines PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 2-4 V aroitus Tämä v aroitusmerkki merkitsee vaaraa. Olet tilanteessa, joka v oi johtaa ruumiin vammaan.
Preparing for Installation 2-5 Electrical Equipment Guidelines Electrical Equipment Guidelines Follo w these basic guidelines when working with any electrical equipment: • Before beginning an y procedures requiring access to the chassis interior, locate the emer gency po wer-of f switch for the room in which you are working.
FCC Class B Compliance PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 2-6 • A void contact between the printed circuit boards and clothing. The wrist strap only protects components from ESD voltages on the body; ESD v oltages on clothing can still cause damage.
CHAPTER VIP2 and the Dual-Port HSSI Port Adapter 3-1 3 VIP2 and the Dual-P or t HSSI P or t Adapter This chapter describes the dual-port high-speed serial interface (HSSI) port adapter and its use on the VIP2 in Cisco 7200 series and Cisco 7500 series routers.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 3-2 Figure 3-2 shows two HSSI port adapters (P A-H Rev . B) installed in port adapter slots 0 and 1, on a VIP2-50.
VIP2 and the Dual-Port HSSI Port Adapter 3-3 Removing a Port Adapter When only one port adapter is installed on a VIP2, a blank port adapter must fill the empty slot to allo w the VIP2 and router chassis to conform to electromagnetic interference (EMI) emissions requirements, and so that air flows through the chassis properly .
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 3-4 Figure 3-4 Pulling a P or t Adapter Out of a Slot (P ar tial P ort Adapter View) Step 7 If you removed a port adapter , place it in an antistatic container for safe storage or shipment back to the factory .
VIP2 and the Dual-Port HSSI Port Adapter 3-5 Installing a Port Adapter Caution T o prev ent jamming the carrier between the upper and lower edges of the port adapter slot, and to assure that the edge .
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 3-6.
CHAPTER Catalyst RSM/VIP2 and the Dual-Port HSSI Port Adapter 4-1 4 Catalyst RSM/VIP2 and the Dual-P or t HSSI P or t Adapter This chapter describes the dual-port high-speed serial interface (HSSI) port adapter and its use on the Catalyst RSM/VIP2 in the Catalyst 5000 family switches.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 4-2 Figure 4-1 Catalyst RSM/VIP2-40 with P A-2H in P or t Adapter Slot 0 Note Port adapters hav e a handle attached, but this handle is not sho wn to allo w a full view of detail on each port adapter’ s faceplate.
Catalyst RSM/VIP2 and the Dual-Port HSSI Port Adapter 4-3 Removing a Port Adapter Caution T o prev ent system problems, do not remove port adapters from the Catalyst RSM/VIP2 motherboard or attempt to install other port adapters on the Catalyst RSM/VIP2 motherboard, while the system is operating.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 4-4 Figure 4-2 Location of P or t Adapter Screw (P artial Port Adapter View) Step 6 Remove the scre w that secures the port adapter (or blank port adapter).
Catalyst RSM/VIP2 and the Dual-Port HSSI Port Adapter 4-5 Installing a Port Adapter Figure 4-4 Installing a New P ort Adapter Caution T o prev ent jamming the carrier between the upper and lower edges.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 4-6.
CHAPTER Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-1 5 Cisco 7200 Ser ies and the Dual-P or t HSSI P or t Adapter This chapter provides information specific to the dual-port high-speed s.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 5-2 Depending on your circumstances, you might need to install a new port adapter in a Cisco 7200 series router or replace a failed port adapter in the field.
Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-3 Replacing a Port Adapter Step 3 Grasp the handle on the port adapter and pull the port adapter from the midplane, about half way out of its slot. If you are removing a blank port adapter , pull the blank port adapter from the port adapter slot.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 5-4 Figure 5-4 Aligning the P or t Adapter Metal Carrier Between the Slot Guides (Cisco 7206 shown) Step 4 W ith the metal carrier aligned in the slot guides, gently slide the port adapter half way into the slot.
Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-5 Replacing a Port Adapter Figure 5-5 Placing the P or t Adapter Le ver in the Locked P osition (Cisco 7206 shown) This completes the procedure for installing a new port adapter or replacing a port adapter in a Cisco 7200 series router .
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 5-6.
CHAPTER Cisco uBR7200 Series and the Dual-Port HSSI Port Adapter 6-1 6 Cisco uBR7200 Ser ies and the Dual-P or t HSSI P or t Adapter This chapter provides information on the P A-2H dual-port high-speed serial interface (HSSI) port adapter and its use on the Cisco uBR7200 series routers.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 6-2 When a port adapter slot is not in use, a blank port adapter must fill the empty slot to allo w the router to conform to EMI emissions requirements and to allow proper air flo w across the port adapters.
Cisco uBR7200 Series and the Dual-Port HSSI Port Adapter 6-3 Removing a Port Adapter Figure 6-3 Placing the P or t Adapter Le ver in the Unlocked P osition (Cisco uBR7223 Shown) Step 3 Grasp the handle on the port adapter and pull the port adapter from the midplane, about half way out of its slot.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 6-4 Replacing a P or t Adapter Follo wing is the procedure for installing a new port adapter in a Cisco uBR7200 series router: Step 1 Attach an ESD-prev entativ e wrist strap between you and an unfinished chassis surface.
Cisco uBR7200 Series and the Dual-Port HSSI Port Adapter 6-5 Replacing a Port Adapter Figure 6-6 Placing the P or t Adapter Retention Clip in the Loc ked Position (Cisco uBR7246 Shown) For a Cisco uBR7223, place the port adapter lev er in the locked position.
Installation Overview PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 6-6.
CHAPTER Cable Installation and Interface Configuration 7-1 7 Cab le Installation and Interf ace Configur ation T o continue your dual-port high-speed serial interface (HSSI) port adapter installation, you must install the port adapter cables and configure the HSSI interfaces.
Attaching a Null Modem Cable PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-2 Figure 7-1 Connecting HSSI Cables (Fr ont View—P A-2H Shown without Handle) Step 2 Attach the network end of your HSSI cables to your T3, E3, or SONET DSU, or other external HSSI equipment.
Cable Installation and Interface Configuration 7-3 Configuring the HSSI Interfaces Note In the Cisco 7206 and Cisco 7206VXR router shelves, you define interfaces by type and physical shelf/port adapter/port locations.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-4 • Whether the ne w interfaces will use bridging For a summary of the configuration options a vailable, refer to the appropriate configuration publications listed in the “If Y ou Need More Information” section on page vii.
Cable Installation and Interface Configuration 7-5 Identifying Chassis Slot, Port Adapter Slot, and HSSI Interface Port Numbers Note P A-2H is considered a high-bandwidth port adapter; therefore, there are specific configuration guidelines that you must observe.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-6 VIP2 P or ts In the router , physical port addresses specify the actual physical location of each interface port on the router interface processor end.
Cable Installation and Interface Configuration 7-7 Configuring Interfaces Follo wing is an example of a basic configuration procedure: Step 1 At the privile ged-lev el prompt, enter configuration mo.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-8 Note If you want to configure cyclic redundancy checks (CRCs) for your port adapter , proceed to the next section, “Configuring Cyclic Redundanc y Checks.
Cable Installation and Interface Configuration 7-9 Checking the Configuration Using show Commands to V erify the New Interf ace Status The following steps use show commands to verify that the ne w interfaces are configured and operating correctly: Step 1 Use the show v ersion command to display the system hardware configuration.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-10 Cisco 7200 Series and Cisco uBR7200 Ser ies sho w Commands Follo wing is an example of ho w the show interfaces [ type slot/port ] command displays status information (including the physical slot and port address) for the interfaces you specify .
Cable Installation and Interface Configuration 7-11 Checking the Configuration Use the show version command to display the configuration of the system hardw are (the number of each port adapter type installed), the software version, the names and sources of configuration files, and the boot images.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-12 Note For complete command descriptions and e xamples for the Cisco 7200 series routers and Cisco uBR7200 series routers, refer to the documentation resources listed in the “If Y ou Need More Information” section on page vii.
Cable Installation and Interface Configuration 7-13 Checking the Configuration Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 1 VIP2 controllers (2 HSSI). 2 HSSI network interfaces. 125K bytes of non-volatile configuration memory.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-14 Use the show controllers cb us command to display all the current interface processors and their interfaces.
Cable Installation and Interface Configuration 7-15 Checking the Configuration Router# show interfaces h 0/0 Hssi0/0 is up, line protocol is up Hardware is HSSI-B Internet address is 5.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-16 Use the show diag command to determine which type of port adapter is installed on a Catalyst RSM/VIP2 in your system.
Cable Installation and Interface Configuration 7-17 Using the ping Command Using the ping Command The ping command allo ws you to verify that an interface port is functioning properly and to check the path between a specific port and connected devices at v arious locations on the network.
Configuring the HSSI Interfaces PA-2H Dual-Port HSSI Port Adapter Installation and Configuration 7-18.
デバイスCisco Systems PA-2Hの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cisco Systems PA-2Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems PA-2Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems PA-2Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems PA-2Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems PA-2Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems PA-2Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems PA-2Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems PA-2Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。