Cisco SystemsメーカーUCS C200 M1の使用説明書/サービス説明書
ページ先へ移動 of 106
Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Cisco U CS C20 0 S er v er .
THE SPECIFICATION S AND INFORMATION REGARDING TH E PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITH OUT NOTICE. ALL STATEMENTS , INFORMATION, AND RECOMMENDATI ONS IN THI S MANUAL ARE BE LIEVED TO BE A CCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED.
iii Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 CONTENTS Preface vii Related Documentation vii Audience vii Organization vii Conventi ons viii Obtaining Documentation and Submitt.
Contents iv Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Status LEDs 3-2 Front Panel LEDs 3-2 Rear Panel LEDs 3-4 Preparing for Component Installa tion 3-7 Required Equipment 3-7 .
Contents v Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Supported Powe r Cords and Plugs B-2 AC Power Cord Illustrations B-3 APPENDIX C RAID Controller Con siderations C-1 Support.
Contents vi Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02.
vii Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface This preface describes the audience, organization, and con v entions of the Cisco UCS C200 Server Installation and Service Gui de . It also provides in formation on ho w to obtain related documen tation.
viii Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface Conventions This document uses the f ollo wing con ventions for no tes, cautions, and safety warnings. Notes and Cautions contain important in formation that you should k now .
ix Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface Attention IMPORT ANTES INFORMA TIONS DE SÉCURITÉ Ce symbole d'avertissement indiq ue un danger . V ous vous trouvez dans une situation pouvant entraîner des blessures ou des do mmages corporels.
x Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface ¡Advertencia! INSTRUCCIONES IMPORT ANTES DE SEGURIDAD Este símbolo de aviso indica peligro.
xi Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface Avis o INSTRUÇÕES IMPORT ANTES DE SEGURANÇA Este símbolo de aviso significa perigo.
xii Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface.
xiii Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface Obtaining Documentation and Submitting a Service Request For info rmation on obtaining documentation, sub mitting a servi.
xiv Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Preface.
CH A P T E R 1-1 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 1 Overview The Cisco UCS C200 Server , which is a part of th e Cisco UCS C-Series Rack-Mount serv er family , is desig.
1-2 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 1 Overvi ew Figur e 1 -2 Fr ont P anel Featur es, Small F or m F actor Caution Do not use the Reset b utton. This b utton is for d ev elopment deb ugging only . This button will reset memory and CPU settings to the def aults.
1-3 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 1 Overview Figure 1-3 sho w s the external features of the rear panel. A Generation M2 server i s show n (the USB ports and the 10/100 Ethernet management po rt are in slightly dif ferent positions for Generation M1).
1-4 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 1 Overvi ew The Cisco UCS C200 serv er has the follo wing compon ents and features. Differ ences between the Large Form F actor (LFF) v ersion of the server (PID R200-1120402W) and the Small F orm Factor (SFF) version of the serv er (PID UCS-BSE-SFF- C200) are noted.
1-5 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 1 Overview Disk Management Factory-conf igured RAID 9 support options, which di f fer for the LFF and SFF versions of the server . • LFF: – RAID 0 and 1 supp ort for up to 4 SA T A driv es with the inte grated SA T A controller .
1-6 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 1 Overvi ew See Appendix A, “T echnical Specifications” for more physical , en vironmental, and power details.
CH A P T E R 2-1 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 2 Installing the Server This chapter describes how to install the server and includes the follo wing sections: • Unp.
2-2 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server Unpacking and In specting the Server Unpacking and Inspecting the Server Ti p Keep the shipping container in case the se rver requires shipp ing in the future.
2-3 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server Preparing for Installation Preparing for Installation This section includes the following topics: .
2-4 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server Preparing for Installation Rack Requirements This section provides the requirem ents for the standard open racks, assuming an e xternal ambient air temperature range of 32 to 95 F (0 to 35 C).
2-5 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server Installing the Server Into a Rack Installing the Server Into a Rack The qualified and supported part numbers for this comp onent are subject to change o ver time.
2-6 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server Installing the Se rver Into a Rack Figur e 2-2 Attaching a Sl ide-Rail Assembly Note The mounting.
2-7 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server Installing the Server Into a Rack d. Attach the second slide-rail assemb ly to the opposite side of the rack. En sure that the two slide-rail assemblies are lev el and at the same height with each other .
2-8 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server Installing the Se rver Into a Rack Step 4 Attach the (optional) cable management ar m (CMA) to the rear of the slide rai ls: Note The orientation in these instructio ns refers to a vie w from the front of the serv er .
2-9 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server Initial Server Setup Initial Server Setup This section contains the following topics: • Connectin.
2-10 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server Initial Server Setup Step 2 Use the supplied KVM cable to connect a keyboard and VGA monito r to the console connector on the front panel (see Figure 1-1 on page 1-1 or Figure 1-2 on page 1-2 ).
2-11 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server Initial Server Setup d. Use this utility to change the NIC redundancy to your preference. This server has three possible NIC redundanc y settings: – None—The Ethernet ports operate independent ly and do not f ail ov er if there is a problem.
2-12 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server Initial Server Setup NIC Modes and NIC Redundancy Settings This server h as the follo wing NIC mode settings th at you can choose from: • Dedicate d—The 10/100 dedicated manageme nt port is used to access the CIMC.
2-13 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server System BIOS and CIMC Firmware System BIOS and CIMC Firmware This section contains information abou.
2-14 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server System BIOS and CIMC Fir mware Accessing the System BIOS Y ou can change the BIOS settings fo r your server by using the procedure in this section.
2-15 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server System BIOS and CIMC Firmware Motherboard Jumpers These jumpers are adjacent to the CMOS battery (see Figu re 2-6 ).
2-16 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server System BIOS and CIMC Fir mware Using the BIOS Recovery Jumper J1E5 to Recover Corrupt BIOS This jumper is adjac ent to the CMOS battery (see Figure 2-6 ).
2-17 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server System BIOS and CIMC Firmware Clearing the CIMC Admin Pa ssword Using Jumper J45 This procedure describes ho w to clear the CIMC admin password back to the def ault in case the user-selected password is lost o f forgotten.
2-18 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server System BIOS and CIMC Fir mware Using the Clear CMOS Jumper J1E6 Y ou can use this jumper to clear the server’ s CMOS settings in the case of a system ha ng.
2-19 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 2 Installing the Server System BIOS and CIMC Firmware Clearing the BIOS Admin Pa ssword Using Jumper J1E4 This procedure describes ho w to clear the BIOS admin password for th e BIOS back to the default in case the user-selected passw ord is lost of for gotten.
2-20 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 2 Installin g the Server System BIOS and CIMC Fir mware.
CH A P T E R 3-1 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 3 Maintaining the Server This chapter describe s how to diagnose hardware problems with status LEDs and ho w to instal.
3-2 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Status LEDs Status LEDs This section describes the locat ions and interpretation s of LEDs on the server that can provide status and troubleshooting info rmation.
3-3 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Status LEDs Figur e 3-2 Fr ont P anel LEDs (Small F or m F act or) Ta b l e 3 - 1 describes the possible states and interp retations for the LEDs that ar e sho wn in Figure 3-1 .
3-4 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Status LEDs Rear Panel LEDs Figure 3-3 sho w s the names and locations of the rear pane l LEDs. A Generation M2 server is sho wn (the USB ports and the 10/100 Ethernet management po rt are in slightly dif ferent positi ons for Generation M1).
3-5 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Status LEDs Ta b l e 3 - 2 describes the possible states and interp retations for the LEDs that ar e sho wn in Figure 3-3 . T able 3-2 Rear P anel LEDs LED Name State Pow er supply status • Off —No A C po wer is present in an y power su pplies.
3-6 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Status LEDs Note The 10/100/1000 Giga bit Ethernet link status LED and the speed LED must be read in combination fo r the follo wing interpretati ons.
3-7 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Preparing for Component Installation Preparing for Component Installation This section descri bes .
3-8 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Preparing for Comp onent Installation Step 1 Check the color of the Power Status LED (see the “Front Panel LEDs” section on p age 3-2 ).
3-9 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Preparing for Component Installation Removing and Replacing the Server Top Cover T o remo ve or replace the server top co ver , follow these steps: War ni n g This unit might have m ore than one power cord.
3-10 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Preparing for Comp onent Installation Removing and Replacing the Server Front Cover (Small Form Factor Only) Note It is not necessary to remove the front cov er unle ss instructed to do so in a replacement procedure.
3-11 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Preparing for Component Installation Replaceable Component Locations This section sho ws the locati ons of the components t h at are discussed in this chapter .
3-12 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Preparing for Comp onent Installation Figure 3-7 Replace able Component Locations, Small For m .
3-13 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Installing or Replacing Components War ni n g This unit might have m ore than one power cord. T o reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit.
3-14 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Replacing a Front Panel Control Module or DVD Module (Small.
3-15 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Note The rear edge of the front cover should go under the black plastic cable cov er . f. Replace the top cover as described in the “Removing and Replacing the Server T op C ov er” section on page 3-9 .
3-16 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-9 Alter nate F r ont P anel Modu le Cable Routing.
3-17 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Installing Hard Drives or Solid State Drives The qualified and supported part numbers for this comp onent are subject to change o ver time.
3-18 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components – If you ha ve th e LFF version of t he server with 3 .5-in dri ves, the f our scre ws install o n the bottom of the sled.
3-19 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Figure 3-12 Dr ive Numbering and Ph ys ical Or ientation, F a.
3-20 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Installing Power Supplies The qualified and supported part numbers for this comp onent are subject to change o ver time.
3-21 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Installing a Fan Tray The qualified and supported part numbers for this comp onent are subject to change o ver time.
3-22 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-15 Removing and Replacing a F an T ra y 1 Securin.
3-23 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Installing DIMMs This section includes the following sections.
3-24 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-16 Ph ysical Repr esenta tion of Banks and Channe.
3-25 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Low-Voltage DIMM Considerations (Gen eration M2 Only) The Generation M2 of thi s server can be or dered w ith lo w-v oltage (1.
3-26 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components DIMM Installation Procedure T o install or replace a DIMM, follo w these steps: Note Refer to the DIMM population rules b efore removing or inst alling DIMMs.
3-27 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Figur e 3-1 7 Rem oving and Replacing Memory Modules 1 DIMM s.
3-28 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Installing CPUs and Heatsinks The qualified and supported part numbers for this comp onent are subject to change o ver time.
3-29 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Figur e 3-18 Removing and Repl acing CPUs and Heatsinks 1 Cap.
3-30 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Installing a Motherboard CMOS Battery War ni ng There is danger of explosion if the battery is replaced i ncorrectly .
3-31 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Figur e 3-19 Removing and Replac ing a Motherboard CMOS Bat tery Installing a Trusted Platform Module The qualified and supported part numbers for this comp onent are subject to change o ver time.
3-32 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components c. Replace the PCIe rise r card assembly . See the “Replacing a PCIe Riser Card Assembly” sect ion on page 3-33 for instructi ons.
3-33 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components h. On the BIOS utility screen, select the Security tab . i. Scroll down to TPM an d select TURN ON . j. Press F10 to sav e your setting s and reboot the server .
3-34 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-21 Removing and Replacin g a PCIe Riser Car d Ass.
3-35 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Replacement Procedure Installing a PCIe card requires that you first remo ve the ri ser card assembly from the chassis.
3-36 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-22 PCIe Slot Number ing and Ph ysical Or ientatio.
3-37 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Special Considerations for the Cisco UCS P81E Virtual Interface Card (N2XX-ACPCI01) The Cisco UCS P81E V irtual Interface Card is a standa rd-profile, half-length, du al-port 10 Gb PCIe car d with SFP+.
3-38 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Installing Multiple PCIe Cards and Resolving Limited Resour.
3-39 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Resolving Insufficient 16-Bit I/O Space The system has only 64 KB of legacy 16-bit I/O resour ces availab le.
3-40 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Replacing an LSI MegaRAID Battery Backup Unit When you install an LSI Me gaRAID card and the op tional BBU in this serv er , do not install the BBU on top of the card as described in t he LSI instructions.
3-41 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Note Be careful to align the arro w-mark on the cable connector wit h the arro w-mark on the socket to av oid damaging the connector pins.
3-42 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Replacing an LSIiBBU08 BBU This BBU is supported b y Cisco .
3-43 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Figure 3-26 Replacing a Mo unting Brack et for the LSIiBBU08 BBU (Enlar ged) Step 2 Install the ne w LSIiBBU0 8 BBU: Note The LSIiBBU08 BBU requires minimum LSI Mega RAID card fi rmware 2.
3-44 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-27 Removing and Replacing an LSIiBBU06 BBU 1 BBU .
3-45 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Chapter 3 Maintaining the Server Installing or Repla cing Components Installing a Mezzanine Card The qualified and supported part numbers for this comp onent are subject to change o ver time.
3-46 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Chapter 3 Main taining the Server Installing or Re placing Components Figur e 3-28 Removing and Replacing a Mezzanine Card 1 Mezz.
A-1 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 APPENDIX A Technical Specifications This appendix lists t he technical specif ications for the Cisco UCS C200 ser ver and incl ude.
A-2 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix A Technical Specific ations Environmental Specifications Environmental Specifications Ta b l e A - 2 lists the en vironmental sp ecifications for the server . Power Specifications Ta b l e A - 3 lists the specifications for each power supply .
B-1 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 APPENDIX B Cable and Power Cord Specifications This appendix pro vides cabl ing and port speci fications fo r control de vices and.
B-2 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specific ations Supported Po wer Cords an d Plugs Supported Power Cords and Plugs Each po wer supply has a sep arate po wer cord. Standa rd po wer cords or jumper power cords are av ailable for connection to the server .
B-3 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs AC Power Cord Illustrations This section contains the A C po wer cord illustrations.
B-4 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specific ations Supported Po wer Cords an d Plugs Figure B-4 SFS-250V -1 0A -CN Figur e B-5 CAB-9K1.
B-5 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Figur e B-7 SFS-250 V -1 0A -IS Figur e B-8 CAB-9K1.
B-6 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specific ations Supported Po wer Cords an d Plugs Figur e B-1 0 CAB-9K1 0A -UK Figure B-1 1 CAB-AC-.
B-7 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specifications Supported Power Cords and Plugs Figur e B-13 CAB-9K12A -NA Figur e B-14 CAB-C13-C14-JM PR, Jumper P o wer Cor d Connector: IEC60320/C15 Cordset rating 13A, 125V (8.
B-8 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix B Cable and Power Cord Specific ations Supported Po wer Cords an d Plugs.
C-1 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 APPENDIX C RAID Controller Considerations This appendix contain s the follo wing sections: • Supported RAID Cont rollers and Req.
C-2 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations Enabling the Integrat ed Intel ICH10R RAID Controller in the BIOS Enabling the Integrated.
C-3 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations Enabling the Me zzanine Card RAID Co ntroller in the BIOS Enabling the Mezzanine Card RAID Controller in the BIOS When using the supported mezzanine-style RA ID controll er card, you must enable the ICH10R controller in Enhanced mode.
C-4 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations How to Determine Which Contr oller Is in Your Server Cisco UCS C200 LFF Server Cabling Th.
C-5 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations How to Disable Quiet Boot For CIMC Firmware Earlier Th an Release 1.2(1) • If the mezzanine-style card is enab led, you are pro mpted to press Ctrl-C to la unch th e configuration for these cards.
C-6 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations Restoring RAID Configur ation After Replacing a RA ID Controller When you boot t he server and y ou hav e quiet boot disabled (see Ho w to Disable Quiet Boot F or CIMC Firmware Earlier Than Release 1.
C-7 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations For More Information For More Information The LSI utilities ha v e help documentation for more information abou t using the utilities.
C-8 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix C RAID Controller Considerations For More Information.
D-1 Cisco UCS C200 Server Insta llation and Service Guide OL-20732-02 APPENDIX D Installation for Cisco UCS Integration The Cisco UCS integratio n instructions ha ve been mov ed to the integratio n gu.
D-2 Cisco UCS C200 Server Installation and Service Guide OL-20732-02 Appendix D Installati on for Cisco UCS Integration.
デバイスCisco Systems UCS C200 M1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cisco Systems UCS C200 M1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCisco Systems UCS C200 M1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cisco Systems UCS C200 M1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cisco Systems UCS C200 M1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cisco Systems UCS C200 M1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCisco Systems UCS C200 M1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cisco Systems UCS C200 M1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCisco Systems UCS C200 M1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。