Code AlarmメーカーCSI-300の使用説明書/サービス説明書
ページ先へ移動 of 12
128- 1 OF 12 Model CSI-300 Owner ’s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORT ANT ! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable manual override circuitry .
128- 2 OF 12 Page 2 YOUR “ Code Hopping “ TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system.
128- 3 OF 12 Page 3 SILENT ARMING - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and hold the Lock button on the keychain transmitter for 2 seconds. ; Dash mounted LED begins to flash slowly .
128- 4 OF 12 Page 4 ; Whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods.
128- 5 OF 12 Page 5 SILENT DISARMING 1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds. ; Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly , indicating that the system is rearming automatically .
128- 6 OF 12 Page 6 p If the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors. These intrusion warning indicators are stored in the system’s memory and will only be erased when the ignition key is turned on.
128- 7 OF 12 Page 7 1 . Disarm the system by use of the transmitter , or by use of the emergency override sequence. Turn the ignition switch to the on position. 2. Within 10 seconds, press and release the valet/override switch, 3 times. 3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
128- 8 OF 12 Page 8 NOTE: If after step 8, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. Y ou will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9.
128- 9 OF 12 during the Panic sounding period. 3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the doors, (if the option is installed), however once the unlock/disarm button is pressed, the vehicle's starter inhibit device, (where installed) will be disabled allowing the vehicle to start.
128- 10 OF 12 Page 10 Check with your installation center for more information on the optional accessory that may have been installed and how it is accessed, as the transmitter buttons must be programmed to access this option if installed.
128- 11 OF 12 CSI-300 SYSTEM FUNCTIONS A T A GLANCE DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH.
128- 12 OF 12 © 2003 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6802 Page 12.
デバイスCode Alarm CSI-300の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Code Alarm CSI-300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCode Alarm CSI-300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Code Alarm CSI-300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Code Alarm CSI-300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Code Alarm CSI-300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCode Alarm CSI-300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Code Alarm CSI-300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCode Alarm CSI-300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
