Compaqメーカー380の使用説明書/サービス説明書
ページ先へ移動 of 34
INTELLISTRIPE 380 USB/RS-232 DESKTOP MOTORIZED READER-ENCODER TECHNICAL REFERENCE MANUAL Manual Part Number 99875275-3 AUGUST 2007 REGISTERED TO ISO 9001:2000 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301 Technical Support: (651) 415-6800 www.
ii Copyright © 2001-2007 MagTek ® , Inc. Printed in the United States of America Information in this document is subject to change without notice. No pa rt of this document m ay be reproduced or transmitted in any form or by any m eans, electronic or mechanical, for any purpose, without the express wri tten permission of MagTek, Inc.
iii REGISTERED TO ISO 9001:2000 MagTek Part Number 9987 5275 -1 1710 Apollo Court, Seal Beach, CA 90740 25 February 2003 Voice: 562-546-6400 Fax: 562-546 -6301 SOFTWARE LICENSE AGREEMENT IMPORTANT: YOU SHOULD CAREFULLY READ ALL THE TERMS, CONDITIONS AND RESTRICTI ONS OF THIS LICENSE AGREEMENT BEFORE INSTALLING THE SOFTWARE PACKAGE .
iv FCC WARNING STATEM ENT This equipment has been tested and found to comply with the lim its for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designe d to provide reasonable protection against harmful interference when the equipment is operated in a co mmercial environment.
v 1 1 1 2 2 2 2 2 4 4 4 4 5 5 5 6 6 6 6 6 6 7 7 7 7 7 8 8 8 8 8 8 8 8 9 9 9 9 9 9 10 11 11 11 11 11 TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFI CATIONS..................................................................................... CONFIGURA TIONS .
vi 11 11 12 19 19 19 19 19 21 21 21 21 21 21 Flange ......................................................................................................................... ........................ MagTek Moun ting Plate..............................
vii viii 1 0 12 12 13 14 14 15 15 16 16 17 1 9 20 20 22 23 24 25 1 0 14 15 16 TABLE OF FIGURES Figure 1-1. IntelliStri pe 380------------------------------------------------------------------------------------------------- -- Table 1.
viii Figure 1-1. IntelliStripe 380.
1 SECTION 1. FEATURES AND SPECIFICATIONS The IntelliStripe ® 380, Desktop Motorized Reader-Encode r reads and encode s m agnetic-stripe cards and smartcards.
IntelliStripe 380 2 APPLICABLE DOCUMENTS Standards ISO 7811-2, -3, -4, -5 Identification cards tracks 1-3 ISO 7810 Physical specifications ISO 7816 Smartcard specifications EMV 1996 Europay-Mastercard.
Section 1. Features and Specifications 3 Motorized Card Transport The Card Transport is based on an existing MagTek magstripe/encode m odule. This module incorporates the following features: Lead-in R.
IntelliStripe 380 4 Spring-Loaded Card Registration Guide(s) The spring-loaded guide ensures that the reference edge of the card is mech anically referenced to the magnetic read/write head, so that the magneti cally encoded track data is physically located on the magstripe in accordance with the specifications of ISO 7811.
Section 1. Features and Specifications 5 Direction of Magnetic Read: The ISO 7810 and 7811 specifications allow for bidirectional magnetic reading of the card.
IntelliStripe 380 6 Cable Management The following provisions are made for communication and power lines: • Polarization and locking of cable connectors • Strain relief of cables • Wire routing functionality • RJ series connectors for main a nd auxiliary RS-232 interfaces.
Section 1. Features and Specifications 7 RAM Space: 40 K bytes ROM Space: ROM Flash: Main Program Memory: 512 K Bytes Boot Loader Memory: 24 K Bytes Configuration Memory: 8 K Bytes Host Serial Port The RS-232 Host Serial Port provides serial communications between the Reader/Encoder and the Host Computer.
IntelliStripe 380 8 Opto-Sensor Inputs The Main PCB provides inputs for the three opto-sensors (Front, Encode, and Rear). Rotary Pulse Generator The Main PCB provides input for the MagTek 75/210 bpi Rotary Pulse Generator (RPG).
Section 1. Features and Specifications 9 External Auto-Ranging Power Pack The Reader/Encoder is powered from an external power-pack, which is located near the Host Computer System.
IntelliStripe 380 10 SPECIFICATIONS The Specifications are listed in Table 1-1. Table 1.1. Specifications OPERATING MSR Read-data Format Specifications Supported Mag-Stripe: ANSI/ISO 7810, 7811/AA MVA.
11 SECTION 2. INSTALLATION The installation of the IntelliStripe 380 Reader-Encoder cons ists of m ounting the unit on a flat surface, connecting the I/O RS-232 cable to the host serial port, th e Auxiliary cable to a peripheral device, and the Power Supply to the I/O cable and to a wall receptacle.
IntelliStripe 380 12 Foot P ads (4) Mounting Screws #4-40 (3) 5.789 3.230 1.616 1.105 .546 Figure 2-1. Dimensions for Mounting Holes for 3-Screw Set and Foot Pads Lock-In-Place Slots (4) Ø .125 Mounting Flange (1) (use with Lock-In-Place mounting holes) 4.
Section 2. Installation 13 . Card Ejector Rod Mounting Flange Card Ejector Rod Rear P anel Guide Slots & Attachment Holes Figure 2-3. Rear Panel and Cover Connect the Host PC cable (P/N 16051417) to th e RS-232 connector on th e IntelliStripe 380 as shown in Figure 2-4 for the RS-232 connection.
IntelliStripe 380 14 Cable P/N 16051417 T o PC P ow er Supply (with cable) P/N 64300091 Nor th American 110V P ow er Cord P/N 71100001 Figure 2-4. Cable Connections - RS-232 Table 2-1 lists the pins for the host cable P/N 16051417. Table 2-1. Pin List for IntelliStripe 380 to Host PC Cable P/N 16051417 10P10C RJ Plug 2.
Section 2. Installation 15 Cable connections for the USB are Shown in Figur e 2-5, and the pin lists are shown in Table 2-2 and Table 2-3. IntelliStripe 380 Back P anel P1 P4 P2 P3 Pin 4 Pin 1 Pin 1 Pin 5 Pin 1 Pin 10 P ow er Supply (with cable) P/N 64300091 Cable P/N 16051422 Nor th American 110V P ow er Cord P/N 71100001 Figure 2-5.
IntelliStripe 380 16 Table 2-3. Cable Connections – USB Power P3 – 2.5 mm Power Jack Wire Color P4 – 10P10C RJ Plug Shell Gnd Drain Wire 1 PWR GND Center Pin +12 26AWG Wire (Black) 2 +12 Shell G.
Section 2. Installation 17 Ejector Rod Hole For Card Remo val P ow er And USB Cable P/N 16051422 Rear P anel Cov er Figure 2-7. Rear Panel Cover Replaced – USB Connection Plug in the power supply into a wall receptacle.
IntelliStripe 380 18.
SECTION 3. OPERATION AND MAINTENANCE The operation of the unit includes inserting and removing the card. Maintenance includes keeping the unit clean and removing jammed cards from the unit. OPERATION The card is inserted with the magnetic stripe down and to the right as illu strated in Figure 3-1.
IntelliStripe 380 Shut power off by unplugging the power supply (Fi gure 2-4), and remove the card with the Rod as follows: 1. Remove the Rear Panel Cover to access th e E jector Rod as indicated in Figure 3-2. Rear P anel Cov er Ejector Rod Hole For Card Remo val Rear P anel Card Ejector Rod Figure 3-2.
21 APPENDIX A. DIMENSIONS FOR MOUNTING MOUNTING The bottom of the unit is shown in Figure 2-1 and 2-2. The IntelliStripe 380 may be mounted in one of three ways: 1) foot pads, 2) set of mount ing holes for 3 screws (4 x 40), and 3) 4 lock-in- place slots.
IntelliStripe 380 Figure A-1. Mounting Dimensions 1 22.
Appendix A. Dimensions for Mounting 23 Figure A-2. Mounting Dimensions 2.
IntelliStripe 380 24 Figure A-3. MagTek Mo unting Plate, I380, 1.
Appendix A. Dimensions for Mounting 25 Figure A-4. MagTek Mo unting Plate, I380, 2.
Appendix A. Dimensions for Mounting 26.
デバイスCompaq 380の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Compaq 380をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCompaq 380の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Compaq 380の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Compaq 380で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Compaq 380を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCompaq 380の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Compaq 380に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCompaq 380デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
