2Wireメーカーthird-party wireless Ethernet adaptersの使用説明書/サービス説明書
ページ先へ移動 of 19
W ir eless Client Configur a tion Guide for third-p arty wireless Ethernet adapters.
Notice to Users ©2002 2W ire, Inc. All rights reserved. This manual in whole or in part, may not be reproduc ed, translated, or reduced to any ma chine-readable form without prior written appro val.
Contents W ireless Client Co nfiguration Guide Introduction ............ ............. ............. ................ ............. ............. ................ ............. ..... ................. ........ 1 Locate the serial number and wireless encryption ke y .
Contents.
1 Wireless adapter configuration Introduction After your 802.1 1b wireless adapter is installed in your computer , you must configure it to communicate with the HomePortal. This guide describes how to configure the following wireless Ethernet (IEEE 802.
2 Agere ORiNOCO PC Card - Silver or Gold Consult the documentation provided with your wireless adapter to in stall the Agere ORiNOCO PC Card - Silver or Gold, then follow these steps: 1. From the Start menu, select Programs > ORi NOCO > Client Mana ger .
3 4. T o create your pr ofile, click Add . The Edit Configuration screen appear s. Enter a profile name in the Profile Name field. The profile name identifies you r wireless p rofile, and should be no more than 29 characters in length. 5. From the Network T ype pulldown menu, select Acces s Point .
4 8. Click Next . In the Set Security field, check the Enable Data Security ch eckbox. V erify that the Use Hexadecimal (0-9, a-f, A-F) radio button is selected. 9. In the Key field, enter yo ur ten-digit W ireless Encryption Key , located on the bottom of your HomePortal.
5 13. In the TCP/IP Behavior field, check the Renew IP Address wh en selecting this profile checkbox. 14. Click Finish . The following screen appears. 15.
6 Cisco Aironet Consult the documentation provided with your wireless card to instal l the Cisco Aironet adapter , then follow these steps: 1. Double-click the Aironet Client Utility icon on your desktop. The Aironet Client Utility screen appears. 2. Click the Profile Manager button.
7 6. Select the System Parameters tab. In the Client Name field, en ter a client name. The client name identifies your PC. 7. In the SSID1 field, enter the word “ 2W IRE ” followed by the last three dig its of your HomePortal serial number . This is the W ireless Netw ork Name.
8 13. Click OK . The Profile Manager screen appears. Y our pr ofile name should now ap pear in the second line of the Profile Management field, indicating that your Cisco ad apter is properly configured.
9 D-Link Air DWL-650 Consult the documentation provided with your wireless adapter to in stall the D-Link Air DWL-650, then follow these steps: 1. From the Start menu, select Programs > D- Link DWL-650 Contro l Utility > Config uration Utility .
10 3. Select the Configuration tab. 4. In the Mode field, enter Infrastruc ture . 5. In the SSID field, enter the word “ 2WIRE ” followed by the last three digits of your HomePortal serial number .
11 13. From the Default Tx Key pulldown, select 1 . 14. Click Apply . 15. Click OK . Apple AirPort card Note: Requir es AirPort client software r evision 2.0 or gr eater . Consult the documentation provided with your wireless adapter to install the Apple AirPort wireless adapter , then follow these steps: 1.
12 3. Select your wireless network name. Y our wireless network na me is “ 2WIRE ” followed by the last three digits of your HomePortal serial number , located on the bottom of your HomePortal. 4. In the Password field, enter “ $” followed by your ten-digit W irel ess Encryption Key , located on the bottom of your HomePortal.
13 3. Enable wireless security . Y our HomePortal is pre-co nfigured to take advantage of wireless security . Referring to the instructions provided with your wireless card, enable wireless security . W ireless security is sometimes referred to as WEP (wired equivalent privacy), 64 -bit encryption , or 40- bit encryption .
14 3. The Connect to W ireless Network screen appears. In the A vailable netw orks field, select your wireless access point. The wireless access point displays as “ 2WIRE ” in all capital letters , followed by the last three digits of the HomePortal serial number (located on the bottom of your Ho mePortal).
5100-000059-000 Rev B.
デバイス2Wire third-party wireless Ethernet adaptersの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
2Wire third-party wireless Ethernet adaptersをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこには2Wire third-party wireless Ethernet adaptersの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。2Wire third-party wireless Ethernet adaptersの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。2Wire third-party wireless Ethernet adaptersで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
2Wire third-party wireless Ethernet adaptersを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又は2Wire third-party wireless Ethernet adaptersの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、2Wire third-party wireless Ethernet adaptersに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわち2Wire third-party wireless Ethernet adaptersデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
