Compaqメーカー8030の使用説明書/サービス説明書
ページ先へ移動 of 42
User’s Guide Compaq TFT8030 Flat Panel Monitor Part Number: 237159-001 July 2001 Enhanced for accessibility.
© 2001 Compaq Computer Corporation. Compaq, the Compaq logo, Armada, Des kpro Registered in U. S. Patent and Trademark Office. Microsoft, MS-DOS, Windows, Windows NT are trademarks of Microsoft Corporation in the United States and other countries. All other product names mentioned here in may be trademarks of their respective companies.
Product Features The Compaq TFT8030 Flat Panel Display has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include the following: ■ Large 18.1-inch (45.9 cm) viewable area display. ■ 1280 × 1024 resolution, plus full-screen support for lower resolutions.
■ Energy Saver feature for Energy Star compliance. ■ Security lock slot ■ AssetControl ■ Compliant with the following regulated specifications: ❏ EPA ENERGY STAR ❏ European Union CE Direct.
Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow these steps: This monitor has multiple connectors on the back panel that can be used to connect two computers simultaneously to the monitor.
WARNING: To reduce the risk of electric shock or damage to your equipment: ■ Do not disable the power co rd grounding plug. The grounding plug is an important safety feature. ■ Plug the power cord into a gr ounded (earthed) electrical outlet that is easily accessible at all times.
After you turn on the monitor, in stall the Compaq LCD Display Assistant utility included on the CD-ROM. Use the on-screen instructions to adjust the picture quality of your monitor. To install this utility, follow the instructions on the “Configuring Your Compaq LCD Monitor” card located in the Program License Agreement packet.
1. Lay the front bezel down on a soft area to prevent it from getting scratched, defaced, or broken. 2. Remove the cover plate from the monitor base by placing your fingers in the opening on the bottom of the base and pulling upward, then pulling out to remove the cover.
The DVI-D connector on this monitor uses digital video information to provide higher speed for higher display resolution. The results are more precise video displays without manually adjusting screen display quality.
Input Select Switch The Video Channel Select control is located at the left-hand side of the lower front bezel. To the left and right of the Select control are two indicators that display the video channel that is selected. The left indicator is for Channel 1 and the right indicator is for Channel 2.
Upon initial power-up, if the mon itor determines that Channel 1 is connected, but the host PC is OFF or sending sleep commands, or Channel 1 does not have a video cable attached, the monitor displays Channel 2 video, if valid. If all video inputs are connected to video sources that are not active (i.
If only one of the user input cha nnels has valid video connected, that input channel is the default at power-up. If the user input video is in sleep mode, the monitor displays the “Going to Sleep” OSD message and enters sleep mode.
Removing the Monitor Base Before you can mount the monitor onto a swing arm or other mounting fixture, you must remove the monitor from the base. CA UTION: Before beginning to disassemb le the monitor, be sure the monitor is turned off and the power and signal cables are both disconnected.
CA UTION: Ensure that the bottom of the monitor base is positioned over a table or deskt op before removing the base from the monitor. 6. Remove the monitor base 3 from the monitor. When the base is removed, f our threaded mounting holes are exposed on the monitor panel to be used for mounting purposes.
Operating the Monitor TFT8030 User’s Guide 13.
Front Panel Controls No. Icon Control Function 1 1-2 Video Channel Select Button Selects the video signal for input to the monito when tw o computers are connected to the monitor at the same time 2 Menu button 1. Launches 1st and 2nd-level on-screen menus.
On-Screen Display Settings The adjustments for screen settings are located in the On-Screen Display (OSD) and can be viewed in one of six available languages.
Advanced OSD Menu Levels Menu Lev el 1 Menu Lev el 2 Menu Lev el 3 Menu Lev el 4 6500 K Custom Color RGB Color ADJ Video Color Hue & Saturation ADJ Cancel Save and Return Language Deutsche English.
Advanced OSD Menu Levels Menu Lev el 1 Menu Lev el 2 Menu Lev el 3 Menu Lev el 4 Set Sleep Time Set On Time Timer SLEEP NOW Cancel Save and Return Basic Menu Cancel Save and Return OSD Control Horizon.
Advanced OSD Menu Levels Menu Lev el 1 Menu Lev el 2 Menu Lev el 3 Menu Lev el 4 Input Channel 1 Analog 1 Digital 1 Auto Detect Input Channel 2 Analog 2 Digital 2 Super Video Composite Video Auto Dete.
Advanced OSD Menu Levels Menu Lev el 1 Menu Lev el 2 Menu Lev el 3 Menu Lev el 4 Save and Return Factory Reset Yes No Exit TFT8030 User’s Guide 19.
How to Adjust Settings 1. To launch the on-screen display menus: ❏ Display the Basic Menu on the monitor screen by selecting the Menu button on the monitor front panel.
2. Select an item from the Main Menu by scrolling down and highlighting it using the Minus (-) button 2 located on the monitor front panel. To reverse or back up, press the Plus (+) button 3 . 3. Highlight your choice and press the Menu button 1 again.
Video Select Button This monitor has multiple signal input connectors (VGA, DVI- Digital, Super Video, and Composite Video) on the back panel for connecting two computers or one computer/one video source to the monitor.
To set the timer: 1. Press the Menu button on the monitor front panel to display the Advanced Menu. 2. Scroll down and highlight Management. 3. Press the Menu button to select Management. 4. Scroll down and highlight and select Sleep Timer > Set Current Time.
The fifth selection, Sleep Now, turns the monitor backlights off immediately and stays in sleep mode until the next On Time activates or a monitor button is pressed. Adjusting Screen Quality Allow the monitor to warm up fo r 20 minutes before performing the following procedures.
When adjusting the Clock and Clock Phase values, if the monitor images become distorted, conti nue adjusting the values until the distortion disappears.
Factory Preset Display Modes Pre- set Pixel Format Horz Freq (kHz) Horz Polarity Vert Frep (Hz) Vert Polarity Pixel Clk (MHz) Source 14 1152 x 900 61.80 +/- 65.96 +/- 92.978 SUN 15 1280 x 1024 63.98 + 60.02 + 108.00 VESA 16 1280 x 1024 79.98 + 75.02 + 135.
Energy Saver Feature When the monitor is in its nor mal operating mode, the monitor utilizes less than 60 watts of power and the Power LED is green. The monitor also supports a reduced power state. The reduced power state will be entered into if the monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal.
■ Use only a power source and conn ection appropriate for this monitor, as indicated on the marking label/back plate and the AC adapter. ■ If an extension cord or power strip is used, make sure th.
Cleaning the Monitor To clean the monitor, follow these steps: 1. Turn off the monitor and the computer. 2. Dust the monitor by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean cloth dampened with isopropyl alcohol.
Specifications Compaq TFT8030 Flat Panel Monitor Display Type 18 inches Flat panel, Active matrix-TFT LCD 45.9 cm View able Image Size 18 inch diagonal 45.9 cm Face Treatment 3H hardness coating with antiglare treatment Maximum Weight (Unpacked) 17.63 lbs.
Compaq TFT8030 Flat Panel Monitor Pow er Source 90 - 264 VAC, 50-60 Hz Pow er Consumption < 60 watts Input Terminals 15-pin D-ty pe connector with cable included. DVI-D connector with cable included. Color Display Values CIE* Chromaticity Coordinates x (+/- 0.
Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules.
Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
EPA Energy Star Compliance Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Compaq Computer Corporation has determined that this product meets the Energy Star guidelines for energy efficiency.
environmentally harmful substa nces are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these pot entially damaging substances sooner or later enter nature.
The energy requirements include a demand that the computer and/or display, after a certain pe riod of inactivity, shall reduce its power consumption to a lower leve l in one or more stages. The length of time to reactivate the computer shall be reasonable for the user.
The relevant TCO'99 demand requi res that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available.
Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the ne rvous system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion of lead since no replacement has yet been developed.
Compaq TFT8030 F lat Panel Monitor User ’s Guide 41.
デバイスCompaq 8030の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Compaq 8030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCompaq 8030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Compaq 8030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Compaq 8030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Compaq 8030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCompaq 8030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Compaq 8030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCompaq 8030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。