Compaqメーカーdx2400の使用説明書/サービス説明書
ページ先へ移動 of 107
Service Reference Guide HP Compaq dx2400 Business PC.
© Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trade marks of Microsoft Corporation in the U.
Table of contents 1 Installing and Customizing the Softwar e Install ing the Operat ing Sys tem ..... ................ ............... ............... ............... ................ ............. ...... ...... 1 Install ing or Upgr ading Devi ce Driver s .
Chassis Designation .................. ............... ............... ............... ................... ............... .......... ........... ..... 18 Microtower (MT) .................. ............... ............. ............... ...............
Speaker ........... ........... ........... ........... ............. ........... ........... ........... ............ ............ ..... ............ ........... 62 Rear Chassis Fan ................ ............... ............... ............... ...
Appendix D System Board and Riser Board Reference Designato rs .......... .................... ..................... .................... ............ .................... ..................... ............ ........... ......... 92 Appendix E Specifications Index .
1 Installing and Customizing the Software NOTE: If the comput er was shipped wit h Windows Vista load ed, you will be pro mpted to register t he computer with HP Total Care before instal ling the operatin g system. You will see a brief movie fo llowed by an online registration form.
HP Backup and Recovery Manager The HP Backup and Recov ery Manager is an easy-to -use, versatile applicatio n that allows you to back up and recover the primary ha rd drive on the PC. The application works within Windows to create backups of Windows, all a pplications, and al l data files.
2 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: ● Change factory default settings. ● Set the system date and time. ● Set, view, change, or verify the sy stem configurat ion, including set tings for graphics, au dio, storage, communications, and input devices.
● Boot ● Exit Use the a rrow keys t o select the appropriate heading, th en press Enter . Use the arrow (up and down) keys to select the op tion you want , then press Enter .
● Memory Bank 4 ● BIOS Revision ● Core Versio n ● Model Number ● Product Number ● Asset Tag (press Enter to change) Computer Setup—Advanced NOTE: Support fo r specific Computer Setup o p tions may vary depen ding on the hardware configuration.
USB Legacy Mode Support Allows you to set: ● Disable d ● Enabled Onboard LAN Allows you to disable/en able onboard LAN contro ller. Onboard LAN Boot ROM Allows you to disable/enable the boot ROM of the onboard LAN chip. SATA1 Controller Allows you to disable/enable the SATA1 Controller.
Computer Setup—Boot NOTE: Support fo r specific Computer Setup o p tions may vary depen ding on the hardware configuration. Table 2-4 Computer Setup—Boot Option Description Boot-time D iagnostic Screen Disables/enables POST di agnostic me ssages display.
Recovering the Configuration Settings To reset all BIO S Setup options to their default values (including options for ctrl+F10 ), you must enter F10 Setup mode an d press F5 . This does not in clude updates to system date , system time , supervis or password , user password , and CPU frequency multiplier .
3 Computer Diagnostic Features HP Insight Diagnostics NOTE: HP Insight Diag nostics is included on CD with some computer models o nly. The HP Insight Diagnostics utili ty allows you to view information abou t the hardware configuration of the computer and perform hardware diagnostic tests on the subsyst ems of the computer.
6. Shut down the operating system and turn off the computer. 7. Turn on the computer. The system will boot to the CD. NOTE: If the system does not boot to the CD in th e optical drive, you may need to.
Test Tab The Test tab allows you to choose various parts of the system to test. You can also choose the type of test and testing mode. There are three types of tests to cho ose from: ● Quick Tes t .
After testing has completed, the Cancel Testing button is replaced with a Retest button. The Retest button will retest th e last set of tests execut ed.
Saving and Printing Informatio n in HP Insight Diagnostics You can save the information displayed in the HP Insigh t Diagnostics Survey and Log tabs to a d iskette or a USB 2.
HP Backup and Recovery Manager The HP Backup and Recov ery Manager is an easy-to -use, versatile applicatio n that allows you to back up and recover the primary ha rd drive on the PC. The application works within Windows to create backups of Windows, all a pplications, and al l data files.
4 Serial and Parallel ATA Drive Guidelines and Features NOTE: Serial ATA = SATA Parallel ATA = PATA SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable 7/7 Number of pins in power cab le 15 Maximum data cable length 39.
SATA Hard Drive Cables SATA Data Cable Always use an HP approved SAT A 3.0 Gb/s cable a s it is fully ba ckwards compat ible with the SATA 1.5 Gb/s drives. Current HP deskt op products ship with SATA 3.0 Gb/s hard dr ives. SATA data cables are susceptible to da mage if ov erflexed.
PATA Device Information The USDT model is the only prod uct that supports a PATA optical dr ive. No PATA drives are supported on any other mode l. ATA SMART Drives The Self Monitoring Anal ysis and Re.
5 Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides general service i nformation for the computer. Ad herence to t he procedures and precautions described in this chap ter is essential for proper service.
Electrostatic Discharge Information A sudden discharge of sta tic electric ity from your finger or other co nductor can destroy stat ic-sensitive devices or microcircuitry.
● Avoid contact with pins, leads, or circu itry. ● Place reusable el ectrostatic-sens itive parts from assemblies in protective packaging or conductive foam.
● Conducti ve foam ● Conductive tablet op workstations with gr ound cord of one-megohm +/- 10% resistance ● Static-dissipative table or floor mats with hard tie to ground ● Field service kits .
Routine Care General Cleaning Safety Precauti ons 1. Never use solvents or flammable solutions to clea n the computer. 2. Never immerse any parts in water or cleaning solutions; a pply any liquids to a cle an cloth and then use the cloth on the component.
● If you remove a key, use a specially desi gned ke y puller to prevent damage to the keys. This too l is available through many electronic supply ou tlets. CAUTION: Never re move a wide leveled key (like the spa ce bar) from the keyboard. If these keys are improperly removed or installe d, the keyboard may not function properly.
● Diagnostics software ● HP tamper-resistant T-15 wrench (Smart Cover FailSafe Key, PN 166527- 001) or HP tamper- resistant bits (Smart Co ver FailSafe Key, PN 166527-002) Screws The screws used in the computer are not interchang eable. They may have standard or metric thre ads and may be of diffe rent lengths.
Lithium Coin Cell Battery The battery that comes with the comp uter provides power to th e real-time clock and has a minimum lifetime of abou t three years. See the appropriat e removal and replacement chapter for the cha ssis you are working on in this guide for instructions on the repl acement procedures.
6 Removal and Replacement Procedures Microtower (MT) Chassis Adherence to the procedures and precautions described in this c hapter is essential for proper servi ce. After completing all nece ssary removal and replacem ent procedures, run the Di agnostics utility to verify that all components operate p r operly.
Preparation for Disassembly See Identifying the Ch assis, Routine Care, and Disassembly Preparati on on page 18 for initi al safety procedures. 1. Remove/disengage any secu rity devices that prohibit opening the computer ( External Security Devices on page 28 ).
External Security Devices The following secu rity devices are used to preven t unauthori zed access to the internal components of the computer and/or se cure the computer to a fixed obj ect.
HP Business PC Security Lock 1. Fasten the security cable by loo p ing it around a stationary object. 2. Thread the keyboa rd and mouse cable s through the lock.
3. Screw the lock to the chassis using the screw prov ided. 4. Insert the plug en d of the security cable into the lock (1) and push the button in (2) to enga ge the lock.
Computer Access Panel 1. Prepare the comp uter for disas sembly ( Preparat ion for Disas sembly on page 27 ). CAUTION: Be fore removing th e computer access pane l, ensure tha t the computer is turned off and that the power cord is discon nected from the electrical outlet.
Front Bezel 1. Prepare the co mputer for disasse mbly ( Preparation for Disassembly on page 27 ). 2. Remove the computer access panel ( Computer Access Panel on page 31 ). 3. Press outward on the three latches on th e right side of the bezel (1) , then rota te the right side of the bezel off the chassis (2) followed by the left side.
Removing Bezel Blanks On some models, there are bezel bl anks covering the 3.5-inch an d 5.25-inch external drive bays tha t need to be removed befo re installing a drive. To remove a bezel blank: 1. Remove the front bezel. 2. To remove a 5.25-inch bl ank, break the blank out of the bezel (1) .
Cable Management Always follow good cabl e management practices when working inside the computer. ● Keep cables away fro m major heat sources like th e heatsink. ● Do not jam ca bles on top of exp ansion cards or memory modules. Printed circuit car ds like thes e are not designed to take excessive pressure on them.
Cable Connections System board connectors are colo r-coded to make it ea sier to find the prope r connectio n. System Board Connections System Board Connector Name Connector Color Description ATXPOWER.
Memory The computer comes wi th double data ra te 2 synchronous d ynamic random access memo ry (DDR2- SDRAM) dual inline me mory modules (DIMMs). The memory sockets on the system board can be po pulated with up to four industry- standard DIMMs. These memory sockets are popul ated with at leas t one pre installed DIMM.
Table 6-1 D IMM Socket Loca tions Item Description Socket Color 1 DIMM socket XMM1, Channel A (populate first) Blue 2 DIMM socket XMM2, Channel A Black 3 DIMM socket XMM3, Channel B (populate second) Blue 4 DIMM socket XMM4, Channel B Black NOTE: A DIMM must occupy the XMM1 socket.
be populated with the tw o 512 MB DIMMs. With this configuration, 2 GB will run as dual channel and 512 MB will run as single channel. ● In any mode, the maximum operational speed is determined b y the slowes t DIMM in the system. CAUTION: The memory module sockets have gold metal contacts.
Expansion Cards The computer has one standard PCI expansion slot that ca n accommodate an ex pansion card up to 17.46 cm (6.875 inches) in length . The computer also has two PCI Express x1 exp ansion slots and one PCI Express x16 expansion slot.
4. On the rear of the com puter, a slot cover lock secures the expansion card brackets in place. Remove the screw from the slot cover lock then slide the slot cover lock up to remove it from the chassis. 5. Before installing an expa nsion card, remove the expansion slot cover or the existing expansion card.
b. If you are removing a standard PCI card, hold the card at e ach end and carefully rock it back and forth until the connectors pull free fro m the socket.
8. To install a new expansion card, hold the card just above the expansion socket on the system board then move the card toward the rear of the ch assis so that the bottom of the bracket on the card slides into the small slot on the chassis. Press the card straig ht down into the expansion socket on the system board.
Drives When installing a dditional drives, follow th ese guidelines: ● The primary Serial ATA (SATA) ha rd drive must be connected to the d ark blue primary SAT A connector on the system b oard labeled SATA0. ● Connect the first SATA optical dr ive to the wh ite SATA connector on the system board labeled SATA1.
CAUTION: To preve nt loss of work and dama ge to the computer o r drive: If you are inserting or removi ng a drive, shut down th e ope rating system properly, turn off th e computer, and unplug the power co rd. Do not remove a d rive while the computer is on o r in standby mode .
System Board Dr ive Connections Refer to the following illustrati on and table to identify the system board drive connectors. Table 6-3 System Bo ard Drive Conn ections No.
Drive Positions 1 Two 5.25-inch external drive bays for op tional drives (optical drives shown) 2 One 3.5-inch external drive bay for opt ional drive (media card reader shown) 3 Primary 3.
Removing an Optical Drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. To remove an opti cal drive: 1. Prepare the comp uter for disas sembly ( Preparat ion for Disas sembly on page 27 ). 2. Remove the computer ac cess panel ( Computer Access Panel on page 31 ).
Installing an Optical Drive into the 5.25-inch Drive Bay To install an optiona l 5.25-inch optica l drive: 1. Prepare the co mputer for disasse mbly ( Preparation for Disassembly on page 27 ). 2. Remove the computer access panel ( Computer Access Panel on page 31 ).
9. Connect the powe r cable (1) and d ata cable (2) to the rear of the optical drive. 10. Replace the front beze l and access panel. 11. Lock any security devices th at were disengage d when the access panel was remove d. The system automatically recognizes th e drive and re config ures the computer.
4. Disconnect the drive cables, as indi cated in the follo wing illustrations: a. If you are removing a diskette dr ive, disconnect the data cable (1 ) and power cab le (2) from the back of the drive. b. If you are removing a media ca rd reader, disconnect the U SB cable from the system board.
5. Remove the retainer screws th at secure the drive to the bay (1) then slide the drive forwar d and out of the bay (2) . Installing a Drive into the 3. 5-inch External Drive Bay The 3.5-inch external drive bay on the front of the co mputer can be configured with a media card re ader or a disk ette driv e.
7. Slide the drive in through the front of the chassis (1) until the bezel on the drive is e venly aligned with the computer front bezel and in stall the M3 metr ic retainer screws (2) a s shown in the illustration below. NOTE: Extra drive retainer screws are provided on the in terior of the front bezel if needed.
Removing an Internal 3.5-inch Hard Drive NOTE: Before you remove the old hard drive, be su re to back up the data from the old ha rd drive so that you can transfe r the data to the new ha rd driv e.
5. Lift the hard disk drive cage o ut of the chassis. 6. Disconnect the power cable (1) and data cable (2) from the back of the hard drive. 54 Chapter 6 Removal and Replacem ent Procedures Microtower .
7. Remove the four screws that secure the hard disk drive to the hard disk drive cage (1) , then slide the hard disk drive out of the hard disk drive cage (2) . Installing an Internal 3.5-inch Hard Drive 1. Follow the steps in Removing an In ternal 3.
2. Slide the new dr ive into the hard d isk drive cage (1) , aligning the drive w ith the four screw holes on the cage. Install the four 6-3 2 standard screws that se cure the hard disk drive to th e hard disk drive cage (2) . Make sure the hard disk drive ca bles are facing the top of the drive cage.
4. Place the hard disk drive cage into the chassis (1) , then slide it down toward the bottom of the chassis until it locks into place (2) . 5. Attach the two screws that secure the hard disk drive cage to the chassis. 6. If installing a new drive, connect the opposite end of the data cabl e to the appropri ate system board connector.
NOTE: If you are repla cing the primary har d drive, use the Recovery Dis c Set to restore the operating system, software drivers, and any software applicat ions that were preinstalled on the computer. Front USB Panel 1. Prepare the co mputer for disasse mbly ( Preparation for Disassembly on page 27 ).
Power Switch/LED Assembly 1. Prepare the comp uter for disas sembly ( Preparat ion for Disas sembly on page 27 ). 2. Remove the computer ac cess panel ( Computer Access Panel on page 31 ). 3. Remove the front bezel ( F ront Bezel on page 32 ). 4. Remove the optical drive ( Removing an Optical Drive on page 47 ).
Heatsink You will need a screwdriver with a narrow shaft to loosen the heatsink screws. 1. Prepare the co mputer for disasse mbly ( Preparation for Disassembly on page 27 ). 2. Remove the computer access panel ( Computer Access Panel on page 31 ). 3. Unplug the fa n cable from the system board (CPU FAN).
Processor 1. Prepare the comp uter for disas sembly ( Preparat ion for Disas sembly on page 27 ). 2. Remove the computer ac cess panel ( Computer Access Panel on page 31 ). 3. Remove the heatsink ( Heatsink on page 60 ). 4. Rotate the locking le ver to its full open positio n (1) .
5. If using a n ew heatsink, remove th e protective cov ering from the bottom of the he atsink and place it in position atop the processor. 6. Secure the heat sink to the system board an d syste m board tray with the four captive screws and attach the heatsink contro l cable to the system board.
When replacing the speaker, be sure to route the wi re behind the ha rd drive cage bracket, through the metal clamp on the chassis, through the metal cla m p on the side of the second hard drive cage, and then down to the system board. Rear Chassis Fan 1.
Power Supply 1. Prepare the co mputer for disasse mbly ( Preparation for Disassembly on page 27 ). 2. Remove the computer access panel ( Computer Access Panel on page 31 ). 3. Disconnect all power cables from the drives and from the system board. 4. Remove the four silver T 15 screws that co nnect the power supply to the chassis.
System Board 1. Prepare the comp uter for disas sembly ( Preparat ion for Disas sembly on page 27 ). 2. Remove the computer ac cess panel ( Computer Access Panel on page 31 ). 3. Remove all expa nsion boards ( Expansion Cards on page 39 ). 4. Disconnect all cables connected to the system board, noting their locati on for reinstallation.
Battery The battery that comes with the computer provide s power to the real-time cl ock. When replacing the battery, use a battery equivalent to the battery origin ally installed in the com puter. The comput er comes with a 3-volt lithium coin cell battery.
Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacement battery in to position, positive side up. 3. The battery holder au tomatically secures the battery in the proper posi tion. 4. Replace the computer acc ess panel. 5.
4. Plug in the comp uter and turn on power to the computer. 5. Reset the date and time and any special system s etups using Computer Setup. Refer to C omputer Setup (F10) Utility on page 3 . Type 3 Battery Holder 1. Pull back on the clip (1) that holds the battery in place, then remove the battery (2) .
A Connector Pin Assignments This appendix contains the pin assignments for ma ny computer and workstation connectors. Some of these connectors may no t be used on the product being serviced.
Ethernet RJ-45 Connector and Icon Pin Sign al 1 2 3 4 (+) Transmit Data (-) Transmit Data (+) Receive Da ta Unused 5 6 7 8 Unused (-) Receive Data Unused Unused Ethernet AUI Connector and Icon Pin Sig.
Parallel Interface Connector a nd Icon Pin Signal Pin Signal 1 2 3 4 Strobe Data Bit 0 Data Bit 1 Data Bit 2 10 11 12 13 Acknowledge Busy Paper End Select 5 6 7 8 Data Bit 3 Data Bit 4 Data Bit 5 Data.
USB Connector and Icon Pin Signal 1 2 3 4 +5 VDC - Data + Data Ground Microphone Connector and Icon (1 /8” miniphone) Pin Signal 1 2 3 1 (Tip) 2 (Ring) 3 (Shield) Audio_left Power_Right Audio_right .
External Infrared Transceiver Connector a nd Icon Pin Signal 1 2 3 4 Transmit Receive Ground 5V 5 6 7 8 Mode Not Used Not Used Not Used Monitor Connector a nd Icon Pin Signal Pin Signal 1 2 3 4 Red An.
ATA/ATAPI (IDE) Standard Drive Cable Connector Pin Signal Pin Signal Pin Signal 1 2 3 4 Reset Ground DD7 DD8 15 16 17 18 DD1 DD14 DD0 DD15 29 30 31 32 DMAK Ground INTRQ IOCS16 5 6 7 8 DD6 DD9 DD5 DD10.
CD-ROM 50-Pin Connector Connector Pin Signal Pin Signal Pin Signal Pin Signal 1 2 3 4 Audio L-ch Audio R-ch Audio GND GND 14 15 16 17 DD12 DD3 DD13 DD2 27 28 29 30 IORDY DMACK INTRQ IOCS 16 40 41 42 4.
24-Pin MicroFit Power Connector 24 12 13 1 F ront Pin Signal Pin Signal Pin Signal Pin Si gnal 1 2 3 4 5 6 +5 Vaux GND +5V +5V PS_ON GND 7 8 9 10 11 12 PWRGD +3.3V +3.3V Tach GND Fan-CMD 13 14 15 16 17 18 +12V +5V Sense GND +5V +5V +3.3V 19 20 21 22 23 24 GND +3.
SATA Data and Power Drive Connector Pin Signal Pin Signal Pin Signal Pin Signal S1 S5 Ground B- S2 S6 A+ B+ S3 S7 A- Ground S4 Ground P1 P5 P9 P13 Ground B- V 5 V 12 P2 P6 P10 P14 V 3.
52 53 54 55 PERp8 PERN8 GND GND 57 58 59 60 PERn9 GND GND PERp10 62 63 64 65 GND GND PERp11 PERn11 67 68 69 70 GND PERp12 PERn12 GND 72 73 74 75 PERp13 PERn13 GND GND 76 77 78 79 80 PERp14 PERn14 GND .
52 53 54 55 GND GND PETp9 PETn9 57 58 59 60 GND PETp10 PETn10 GND 62 63 64 65 PETp11 PETn11 GND GND 67 68 69 70 PETn12 GND GND PETp13 72 73 74 75 GND GND PETp14 PETn14 76 77 78 79 80 GND GND PETp15 PE.
31 32 33 34 36 36 PETn0 SMB_DATA PETp0 GND GND USB_D- 37 38 39 40 41 42 Reserved* USB_D+ Reserved* GND Reserved* LED_WWAN# 43 44 45 46 47 48 Reserved* LED_WLAN# Reserved* LED_WPAN# Reserved* +1.
B Power Cord Set Requirements The power supplies on some computers have external power switches. T he voltage select switch feature on the computer permits it to operate fro m any line voltage between 100 -120 or 220-240 volts AC.
Country-Specific Requirements Additional requ irements specific to a countr y are shown in parentheses and explained below. Country Accrediting Agenc y Country Accrediting Agen cy Australia (1) Austri.
C Troubleshooting Safety and Comfort WARNING! Misuse of the c omputer or failure to e stab lish a safe and comfort abl e work environment may result in disco mfort or serious injury. Refer to the Safety & Comfort Guide available on the We b site at http://www.
To assist you in resolving problems online, HP In stan t Support Professional Edition pro vides you with self-solve diag nostics. If you need to contact HP su pport, use HP Inst ant Support Profes sional Edition's online chat fea ture. Access HP Instant Support Pro fessional Edition at: http://www.
● If you have installed an operating syste m other than the factory-installed operating system, check to be sure that it is supported on the system. ● If the system has multiple vi deo sources (em.
Computer will not respond to USB keyboard or mouse. Cause Solution Keyboard or mouse is not connected to co mputer. Connect keyboard and mouse cables to computer. Computer is in standby mode. To resume from standby mod e, press the power button or press any key.
Poor performance is experienced. Cause Solution Too many applications running. 1. Close unnecessary applications to free up memory. Some applications run in the background and can be closed by right-clicking on their correspon ding icons in the task tray.
Computer is beeping and will no t start. Cause Solution Internal error has occurred and the computer is bee ping a code. Refer to Interpreting POST Audible Codes on page 90 to interpret the error code.
Computer will not start. Cause Solution Wrong memory modules were used in the upgr ade or memory modules were installed in the wrong location. 1. Review the documentation that came with the system to determine if you are using the corre ct memory modules and to verify the proper installation.
Interpreting POST Audible Codes This section covers th e audible codes that may o ccur before or during POST that do not ne cessarily have an error code o r text message associ ated with them. WARNING! When the computer is plug ged into an AC power sou rce, voltage is always appl ied to the system board.
Contacting Customer Support For help and service, contact an authorized reseller or dealer. To locate a reseller or deal er near you, visit http://www.hp.com . NOTE: If you take th e computer to an au thorized re seller, dealer, or service provider for service, remember to provide the setup and power-on passwords if they a re set.
D System Board and Riser Board Reference Designators These reference designators a re used on most but not al l HP system and riser boards. Designator Component BAT CR1 CR2 CR3 CR4 Battery socket/Batt.
J38 J39 J40 Secondary SCSI connector Stacked parallel/SCSI connector AGP sl ot J41 J50 J51 J52 J53 x16 PCI Express slot for graphics First parallel port Second parallel port Double-stacked parallel po.
L3 L4 L5 P1 USB rear port choke (2nd) USB rear port choke (3rd) USB front port choke (2nd) P/S connector (20 or 24 pin ) P2 P3 P4 P5 P6 Second P/S connector (as required) Processor 12V header Secondar.
P54 P55 P58 P60 P61 Primary serial port Double stack serial port, Top = Serial B, Bottom = Serial A Riser edge connector (male-mates with J30) PrimarySerial ATA (SATA) connector Second Serial ATA (SAT.
U4 U5 South bridge Super I/O U6 U7 U10 U11 U12 Clock ch ip 64 bit Bridge LOM1 LOM1 EEPROM LOM1 PHY U13 U14 U16 U17 U18 Audio Codec Audio amplifier LOM2 LOM2 EEPROM LOM2 PHY U19 U20 U21 U29 U30 U31 SPI.
Y4 Y5/H5 Secondary NIC clock cr ystal RTC clock crystal/tie-down 97.
E Specifications Table E-1 Spec ificatio ns Desktop Dimensions Height Width Depth 16.37 in 7.24 in 14.95 in 41.58 cm 18.40 cm 37.98 cm Approximate Weight 20.77 lb 9.42 kg Temperature R ange Operating Nonoperating 50° to 104°F -22° to 140°F 10° to 40°C -30° to 60°C Relative Humidity (noncondensing) Operating Nonoperating (38.
Rated Input Current (maxim um) 1 8A @ 100 VAC 4A @ 200 VAC 1 This system utilizes a passive power factor corrected po wer supply. The power factor correction is present in the 230V operating mode only. T his allows the system to pass the CE ma rk requirements for use in the countries of the European Union.
Index Symbols/Numerics 24-pin MicroFit pow er pin assignments 76 24-pin power pin ass ignments 75 4-pin power pin a ssignments 76 6-pin power pin a ssignments 76 A ATA/ATAPI (IDE) drive cable pin assi.
M media card read er installing 51 removing 49 memory removal and repl acement 36 microphone pin assign ments 72 monitor pin assignments 73 mouse cleaning 23 pin assignments 69 O operating guidelines .
デバイスCompaq dx2400の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Compaq dx2400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCompaq dx2400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Compaq dx2400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Compaq dx2400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Compaq dx2400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCompaq dx2400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Compaq dx2400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCompaq dx2400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。