Compatible SystemsメーカーOCTAL V.35の使用説明書/サービス説明書
ページ先へ移動 of 18
Octal V .35 - Quad 10/100 RIOP Installation Guide Comp atible Systems C orporati on 4730 W alnut Street Suite 1 02 Boulder , Co l or ad o 80301 303- 444- 9532 800- 356- 0283 http://www.
Octal V .35-Quad 10/100 R IOP Instal lation Guid e, V ersion 1.0 Copyri ght© 1999 , Compat ible Systems Co rporat ion All rights reserved. VSR, VSR-2, MicroRouter and CompatiV iew are trademarks of Compatible Systems Corporation. Other trademarks are the p roperty of their respective holders.
T able of Contents i Introd uction to the Oc tal V. 35-Quad 10/100 RIOP 1 Chapter 1 - Network Installation 2 Connecting the Octal V. 35-Quad 10/100 t o the Ethe rnet 2 Telco Li ne Conne ction R equiremen ts 2 Connecting a Line Device to the V.
T able of Contents ii IP Prot ocol 9 Required for IP Numbere d Interface 9 Suggested fo r IP 9 IPX Pr oto col 10 Required for IPX 10 Suggested fo r IPX 10 Apple Talk Prot ocol 10 Requ ire d for Appl e.
Introduction to the Octal V .35-Quad 10/100 RIOP 1 Introduction to the Octal V .35-Quad 10/100 RIOP The Octa l V .35-Qu ad 10/100 Routi ng Input/ Output Pro cessor (R IOP), as part of the VSR multigigabit switching r outer , allows you to connect up to fou r local Ethernets and up to eight remote corpor ate networks.
Chapter 1 - Network Instal lation 2 Chapter 1 - Network Installation Octal V .35-Quad 10/100 RIOP Front Panel This section of the manual will help you in stall the Octal V .35-Quad 10/100 RIOP to connect up to four local Ether nets and up to eight r emote corpo rate networks .
Chapter 1 - Network Instal lation 3 The Octal V .35 -Qua d 10 /10 0 RIOP is ship ped with two “ Quad ” cables. These cables have a single V ery High Dens ity D-Sub connector wh ich plugs into o ne of the Quad V .
Chapter 2 - Quicksta rt Instructions 4 Chapter 2 - Quickstart Instructions This Quickstart chapter briefly discusses the m ajor parameters that must be set in order to use the Octal V .35-Quad 10/100 RIO P as par t of your V SR multigig abit switchi ng rout er .
Chapter 2 - Quicksta rt Instructions 5 Suggested fo r IP These parameters h elp supply infor mation about the segmen t that the interface is conn ected to.
Chapter 2 - Quicksta rt Instructions 6 DECnet Protocol Required for DE Cnet The router ’ s ship ping conf iguratio n does not have DEC net turned o n.
Chapter 2 - Quicksta rt Instructions 7 IP Protoc ol Required fo r IP W AN interfaces which are set for PPP operation do not ge nerally use an IP ad dress. They ar e set to act as an “ unn umbered in terface. ” In this mo de of operation, there are no required settings.
Chapter 2 - Quicksta rt Instructions 8 In CompatiV iew yo u must set a global parameter and a port-specific parameter . Suggested fo r DECnet Setting the parameters abo ve s hou ld be adequ ate for most installations . Frame Relay Configuration This section covers the settings requ ire d for Fram e Relay oper atio n of the V .
Chapter 2 - Quicksta rt Instructions 9 IP Protoc ol There are two ways to set up Frame Relay . One is to s et the W AN interface as a “ numb ered interface. ” This means that the in terface (and thus the Frame Relay network) will have an IP address, subnet mask, etc.
Chapter 2 - Quicksta rt Instructions 10 IPX Pr otoco l Required fo r IPX Frame Relay operation requ ires that the W AN interface be set as a “ numbered interface. ” This means that the inter face (and thus the Frame Relay ne twork) mus t have an IPX network numb er .
Chapter 2 - Quicksta rt Instructions 1 1 SMDS Configur ation This section covers the settings require d for SMDS (Switch ed Multi-megabit Data Service) operation of the V .35 W AN interfaces (IP on ly). SMDS is a connectionless, pack et-switched service that of fers LAN-to- LAN connectivity across a wide area at up to 1.
Chapter 3 - Shipping Def aults 12 Chapter 3 - Shipping Defaults Ethernet Interfaces IP Routing Defa ults • Off, all in terfaces IP Bridging Defaults • On, all interfaces • Addr ess: 198. 41.12 .1 • Subnet Mas k: 255.255.2 55.0 • Broadcast Address: 198.
Chapt er 4 - LED Pat terns 13 Chapter 4 - LED Patterns Some of the LEDs on the front of the VSR multig igabit switching router serve dual functions. In addition to indicating certain router -wide o perating conditions, they may also display port-specifi c informat ion.
Appendix A - Connector and Cable Pin Outs 14 Appendix A - Connector and Cable Pin Outs Pin Outs for HD D-Sub Male to V .35 Male Cable 1 Unused by the V .35 interface circuitry . 2 Receive Line Signal Detect (RLSD) must be asserted b y the CSU/DSU when the W AN line is operational.
デバイスCompatible Systems OCTAL V.35の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Compatible Systems OCTAL V.35をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCompatible Systems OCTAL V.35の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Compatible Systems OCTAL V.35の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Compatible Systems OCTAL V.35で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Compatible Systems OCTAL V.35を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCompatible Systems OCTAL V.35の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Compatible Systems OCTAL V.35に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCompatible Systems OCTAL V.35デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
