Agilent Technologiesメーカー81101Aの使用説明書/サービス説明書
ページ先へ移動 of 123
S S 1 Agilent 81101 A 50 MHz Pulse Generator Reference Guide.
Per 1.000 µ µ µ µ s Normal OUTPUT TRG-LEV LIMITS MODE/TRG OFF Delay 1 0ps Width LeadE TraiE 100.0ns 5.00ns =LeadE Offset Amplit +0.0mV 1.00V 50 Ω Ω Ω Ω into 50.
Refer ence G uide Agilent 81101 A 50 MH z Pulse Generator Part No . 81101-91 021 Printed in Germany March 200 0 Edit ion 1.0, E0 300.
4 Notice Notice Copyrigh t 1998 A gilen t T echn ologies 1 998, 2 000. Al l righ ts rese rved. No part of this manual ma y be reproduc ed in any for m or by any mean s (includin g electro nic stora ge and ret rieval or tran slation int o a foreign language ) without prior agreeme nt and written conse nt from Agile nt T echn ologies Inc.
5 Notic e Agilent T echnologies warrants that its software and firmware de signated by Agilent T e chnologies for use with an instrume nt will execute its progra mming instructions w hen properly insta lled on that instrum ent.
6 Safety Summa ry Safety Summary The fol lowin g genera l saf ety prec autions mu st be ob served d uring a ll phases of opera tion of this instrument. Failure to comply with these precau tions or with specific wa rning s elsewhe re in this m anual v iolates safety standa rds of design, manufacture, a nd intended use of the instrument .
7 Safety Summ ary Ground the Instrument T o minimize shock ha zard, the instrument chassis and c over must be connect ed to an electri cal pr otecti ve eart h ground .
8 Safety Summa ry Safety Sym bols Caution (re fer to accomp anying do cuments) Protec tive earth (ground) te rminal In th e man uals : WAR NIN G The W ARNING sig n denotes a hazard. It calls a ttenti on to a procedur e, practice, o r the like, which, if no t correct ly performed or adher ed to, coul d res ul t in pe rson al i njur y .
9 About this Book About this Book This gu ide prov ides refe rence i nformati on primar ily fo r program ming the Agilen t 81101A via rem ote contr ol. Chapter 1 “General Programming As pects” on page 13 gi ves gene ral hints for prog ramming inst ruments like the Agilen t 81101A usin g SCPI comm ands.
10 About thi s Book Conventions U sed i n this Book This book uses certain conv entions to indic ate elements of the Agilen t 81101A ’ s user inte rface . The foll owing ta ble sho ws some exam ples: Softkeys Press the MO DE/TRG softk ey to access the Mode/ T rigger scr een.
xi Contents Notice .................. ............................... ................................ ........ 4 Safety Summary ................................. ................................ ........ 6 About this Book ............ ...............
xii Contents Agilent 81101A S pecifications ............................. .................. 91 General .......... ................. ........... ................. ................. ........... ................ 91 Timing Specifications .............. .
13 1 1 General Programming Aspects This ch apter pr ovides general i nformat ion on wri ting GP-IB/SCPI programs f or instruments lik e the Agilent 81 101A. Detailed informa tion on pr ogramming the Agile nt 81101A ca n be found in Chapter 2 “Programming Reference” on page 25 .
14 General Programming Aspects The GP -IB Inte rface Bus The G P-IB Inte rface B us The Gene ral Pu rpose In terface Bus is the interf ace used for comm unicatio n betw een a controll er an d an ex tern al devic e, suc h as t he Agilen t 81130A. The GPIB co nforms to IEEE sta ndard 488- 1987, ANSI standa rd MC 1 .
15 General Programming Aspects Agilent 81101A Remo te Control Agilent 81101A Remote Control GP-IB Address Y ou can only set the GP-IB address from the front pane l of the instrumen t (refe r to th e Quick Star t Gui de ). The default GP-I B address is 10.
16 General Programming Aspects Progr ammin g Recom menda tions Programming Recommendations Here are som e recommenda tions for progra mming the in strument: • Start prog ramming f rom the def ault setting .
17 General Programming Aspects Progr amming Reco mmendatio ns When you have fou nd the co rrect set ting, then use thi s to cr eate the progra m. In the p rogram it is reco mmended to send t he comm and for enabli ng outp uts (for exampl e, : OUTPu t ON ) as the last command .
18 General Programming Aspects Common Command Summary Common Command Summary This table summ arizes the IEEE 48 8.2 commo n commands supp orted by the Agi lent 81101A: Command Paramete r Descripti on .
19 General Programming Aspects Status Model Status Model The instrum ent has a status repor ting system co nforming to IEEE 488.2 and SCP I. The above f igure shows t he status group s availab le in the instrument . Each status grou p is made up of comp onent registe rs, as shown in the followi ng figure.
20 General Programming Aspects Status Mode l Condition Register A condit ion register contains the curren t status of the hardware a nd firmware. It is co ntinuously upd ated and is no t latched or buffere d. Y ou can on ly rea d condi tion registers.
21 General Programming Aspects Status Model Enabl e Register The enabl e register defi nes which bits i n an event register are in cluded in the log ical OR into the summ ary bit. The enable r egister i s logicall y ANDed with the e vent register and the r esulting b its ORed i nto the summary bit.
22 General Programming Aspects Status Mode l Status By te The statu s byte sum marize s the infor mation from all ot her st atus gro ups. The sum mary bi t for the status byte act ually appears i n bit 6 (RQS) of the status byte.
23 General Programming Aspects Status Model OPERation Status Group This Status Grou p is not used in the instru ment. Bit De scrip tion 0 Unus ed, alw ays 0 1 Unus ed, alw ays 0 2 Unus ed, alw ays 0 3.
24 General Programming Aspects Status Mode l QUEStionable Status Group The QUES tionable Status g roup is used to repo rt warning conditions amongst th e voltage, cu rrent, pulse timin g and freque ncy parameter s.
25 2 2 Programmin g Reference This ch apter pr ovides referen ce infor mation on the followin g topics: • “Agilent 81 101A SCP I Command Su mmary” on page 26 • “Def ault Value s, St andar d .
26 Programming Reference Agilent 81101A SCPI Command Summary Agilent 81101A SCPI Command Summary Command Parameter D escriptio n see page :ARM (T rigge r mode and source) [:SEQuence[1] | :STARt] [:LAY.
27 Programming Reference Agilent 81101A SCPI Command S ummary :OUTPut[1] [:NORMal] [:STATe] OFF|ON|1|0 Set/read normal outpu t state :IMPedance 47 [:INTernal] <value> Set/read internal source im.
28 Programming Reference Agilent 81101A SCPI Command Summary :DOUBle[1] [:STATe] OFF|ON Enable/disable double pulses per pulse period 59 :DELay <value> Set/read de lay between doubl e pulses 60 .
29 Programming Reference Agilent 81101A SCPI Command S ummary :OFFset <value> Set/read channel o ffset vol tage 71 :HIGH <value> Set/read channel h igh level voltage 72 :LOW <value> .
30 Programming Reference Agilent 81101A SCPI Command Summary [:STATe] ON|OFF Switch security on and off 82 :SET Block data Set/read compl ete instrument setting 83 :VERSion? Read SCPI com pliance sett.
31 Programming Reference Default Values, Standard Settings Default V alues, Standard Settings Parameter *RST , Default V alues :ARM : E WIDth: ST A T e OFF :FREQ uency 100kHz :IMPedanc e 50 Ω :LEV e l +1.
32 Programming Reference Default V alues, Standard Settin gs :LOW –1 0.0mA :ST A T e OFF :FREQ [:CW|:FIX ed] 1.00MHz :AUTO not applicable :HOLD VOL T :PHASe[1][:ADJust] 0.
33 Programming Reference Default Values, Standard Settings [:SOURce ]:VOL Tage[1] :LEV e l] [IMMedi ate] [:AMPLitude] 1.0V :OFF Set 0.0V :HIG H 500mV :LOW –5 00mV :LIMIt[:High] +50 0V :LOW –5 00V .
34 Programming Reference Default V alues, Standard Settin gs :LEV el 1.0V :SLOPe POSitive :SOUR ce IMMediate Parameter *RST , Default V alues.
35 Programming Reference Programming the In strument T rigger Modes Programming the Instrument T rigger Modes The following figure show s the instrum ent’ s arming /triggering model: Y ou program the c omprehensive trig gering capabilit ies of the instrum ent using th e SCPI :ARM and :TRIGger subsystems.
36 Programming Reference Progr ammi ng the I nstru ment T r igg er Mode s Use the :ARM s ubsyst em to s elect the overal l tri ggerin g mode of the instrument ( CONTIN UOUS , TRIGGERE D , GATE D , EXT.
37 Programming Reference Programming the In strument T rigger Modes External W idth Set Exte rnal W idth mod e using the :E WIDt h[:STA Te] command: :ARM:EWIDth ON Switch on EXT WIDTH mode This c ommand disables the arm- trigger sy stem. The ar m-trigg er system i s reenable d by switc hing O FF EWIDth mode.
38 Programming Reference SCPI Instrument Command List SCPI Instrument Command List The fol lowing r eferenc e sections list th e instrumen t comman ds in alphabe tical order . In addition to a command desc ription, the att ributes of each co mmand ar e described u nder the follow ing heading s.
39 Programming Reference SCPI Instrume nt Command List Command :ARM:EWID Long :ARM[:SEQuence[1]|STAR t][:LAYer]:EWIDth[:STATe] Form Set & Query Parameter ON | OFF | 1 | 0 *RST value OFF Description Use this co mmand to enable t he EXT WIDTH t rigger mode avai lable on the M ODE /T RI GGER SCREEN .
40 Programming Reference SCPI Instrument Command List Command :ARM:IMP Long :ARM[:SEQuence[1]|STAR t][:LAYer]:IMPedance Form Set & Query Parameter Num eric Parameter Suffix OHM with en gineering p refixes, e.
41 Programming Reference SCPI Instrume nt Command List Command :ARM:P ER Long :ARM[:SEQuence[1]|STAR t][:LAYer]:PERiod Form Set & Query Parameter Num eric Parameter Suffix S or SE C with e ngineer ing pref ixes. *RST value 10.0 0 µ s Specified Limits 20 ns to 999.
42 Programming Reference SCPI Instrument Command List Command :ARM:SENS Long :ARM[:SEQuence[1]|STAR t][:LAYer]:SENSe Form Set & Query Parameter EDGE | LEVe l *RST value EDGE Description Use this command to selec t T rigge red or Gate d mode by choosing whethe r the instrum ent arm s on the e dge(s) or level of the a rming signal.
43 Programming Reference SCPI Instrume nt Command List Command :ARM:SOUR Long :ARM[:SEQuence[1]|STAR t][:LAYer]:SOURce Form Set & Query Parameter IM Mediat e|INTer nal[1] |INT ernal2 |EXTern al[1].
44 Programming Reference SCPI Instrument Command List Command :MMEM:CA T? Long :MMEMory:CATalog? Form Query Parameter [" A:"] *RST value Not applicable Description Use this co mmand to get a list ing of the conte nts of the curr ently select ed dire ctory on the me mory ca rd.
45 Programming Reference SCPI Instrume nt Command List Command :MMEM:COPY Long :MMEMory:COPY Form Even t Parameter "f ilenam e"[,"A: "],"co pyna me"[," A:"] *RST Not applicable Description Use this command to c opy an existi ng file filename in the current directory to a new file copyname .
46 Programming Reference SCPI Instrument Command List Command :MMEM:LOAD:ST A T Long :MMEMory:LOAD:STATe Form Even t Parameter <n >,"fil ename"[ ,"A:"] *RST Not applicable Sp.
47 Programming Reference SCPI Instrume nt Command List Command :OUTP[1] Long :OUTPut[1][:NORMal][:S TATe] Form Set & Query Parameter ON | OFF | 1 | 0 *RST value OFF Description Use this command to swit ch the norma l OUTPUT on or off .
48 Programming Reference SCPI Instrument Command List Specified Lim its 0.1 Ω to 1 M Ω Description Use this co mmand to set the e xpected l oad imped ance of th e devi ce under test at the OUT PUT conn ecto rs.
49 Programming Reference SCPI Instrume nt Command List V alu e coupl ing Range co upling Offset Description Use this co mmand to program th e ampl itude cur rent of the OUTPUT signal.
50 Programming Reference SCPI Instrument Command List Range co upling Amplitude Description Use this co mmand to p rogram the offset current o f the OU TPUT signal. Note th at to set t he OUTPU T levels i n terms of curren t, you f irst have to exec ute th e [:SOUR ce]:HO LD CURRe nt command to enabl e the :SOURc e]:C URRent subsystem.
51 Programming Reference SCPI Instrume nt Command List have t o execut e [:SOUR CE]: HOLD CUR Re nt comm and to enable the [:SOUR CE]: CURRent subsystem.
52 Programming Reference SCPI Instrument Command List • Specif ied Volt age limi ts • Actual OUTPUT Impedance setting :OUTPu t:IMPe dance • Actu al Ex pecte d Load impe danc e sett ing: :OUTPU T.
53 Programming Reference SCPI Instrume nt Command List Command :CURR[1 ]:LIM:LOW Long [:SOURce]:CURRent[1]:L IMit:LOW Form Set & Query Parameter Num eric Parameter suffix A with engi neering p refixes. *RST value –10.0 mA Description Use this command to set/read th e low le vel curren t limit.
54 Programming Reference SCPI Instrument Command List Example T o set and ac tivate the curren t limits fo r the outp ut: Command :FREQ Long [:SOURce]:FREQuency[:C W|:FIXed] Form Set & Query Parameter Num eric Parameter Suffix Hz wit h engin eering pre fixes, or MH Z for Megahe rtz.
55 Programming Reference SCPI Instrume nt Command List Command :FREQ:AUTO Long [:SOURce]:FREQuency[:C W|:FIXed]:AUTO Form Even t Parameter ON CE *RST value Not applicable Description Use this co mmand to m easure the frequen cy at th e CLK-IN co nnector .
56 Programming Reference SCPI Instrument Command List Command :PHAS[1] Long [:SOURce]:PHASe[1][:AD Just] Form Set & Query Parameter Num eric Parameter suffix DEG or RA D .
57 Programming Reference SCPI Instrume nt Command List Command :PULS:DCYC[1] Long [:SOURce]:PULSe:DCYCle [1] Form Set & Query Parameter Num eric V alu e coupl ing *RST value 10.0% (der ived fro m width and peri od) Specified li mits 0.001% to 99.9% , depends on width, tra nsition & period.
58 Programming Reference SCPI Instrument Command List Specified li mits 0.00 ns to 999 s (lim ited by peri od – 20 ns) Description Use this co mmand to set/rea d the puls e delay . Delay is the t ime be tween the start of the pu lse period and the st art of th e leading e dge of t he pulse.
59 Programming Reference SCPI Instrume nt Command List Command :PULS:DEL[1]:UNIT Long [:SOURce]:PULSe:DELay[ 1]:UNIT Form Set & Query Parameter S | SEC | PCT | DEG | RAD *RST value S Description Use this co mmand to set/rea d the defa ult un its for the pul se dela y paramet er .
60 Programming Reference SCPI Instrument Command List Command :PULS:DOUB[1]:DEL Long [:SOURce]:PULSe:DOUBle [1]:DELay Form Set & Query Parameter Num eric Parameter suffix S with engi neering p refixes. Y ou c an change the defau lt unit usi ng [:SOUR ce]: PULSe:D OUBle: DELay[ 1]:UNIT .
61 Programming Reference SCPI Instrume nt Command List Command :PUL S:DOUB [1]:DEL:H OLD Long [:SOURce]:PULSe:DOUBle [1]:DELay:HOLD Form Set & Query Parameter TI ME|PRA Tio *RST value TIME Descrip.
62 Programming Reference SCPI Instrument Command List Command :PUL S:HOLD [1] Long [:SOURce]:PULSe:HOLD[1 ] Form Set & Query Parameter WI DTh | DCYCl e | TDELay *RST value WIDTh Description Use th.
63 Programming Reference SCPI Instrume nt Command List Y ou cannot set the pulse period if you have selecte d the CLK-IN connect or as the freq uency so urce ( :TRIG: SOUR EX T ).
64 Programming Reference SCPI Instrument Command List Example T o pr ogram the p ulse width by mea ns of the delay parameter s: Command :PULS:TRAN[1]:H OLD Long [:SOURce]:PULSe:TRANsi tion[1]:HOLD For.
65 Programming Reference SCPI Instrume nt Command List Command :PULS:TRAN[1]:UNI T Long [:SOURce]:PULSe:TRANsi tion[1]:UNIT Form Set & Query Parameter S | SE C | PCT *RST value S Description Use this command to set the default units for th e pulse tran sition times.
66 Programming Reference SCPI Instrument Command List Command :PULS:TRAN[1]:TR A Long [:SOURce]:PULSe:TRANsi tion[1]:TRAiling Form Set & Query Parameter Num eric Parameter suffix S with engi neeri.
67 Programming Reference SCPI Instrume nt Command List Command :PULS:TR AN[1]:TRA:AUTO Long :[SOURce]:PULSe:TRANsi tion[1]:TRAiling:AUTO Form Set & Query Parameter ON |OFF|O NCE *RST value ON Description Use this comm and to set /read the automatic co upling of the pulse t railing edge tran sition time to the le ading edge transition ti me.
68 Programming Reference SCPI Instrument Command List Command :PULS:WIDT[1] Long [:SOURce]:PULSe:WIDTh[ 1] Form Set & Query Parameter Num eric Parameter suffix S with engi neering p refixes *RST value 100 n s Specified li mits 10 ns to 999.5 s (max.
69 Programming Reference SCPI Instrume nt Command List Example T o set up th e external PLL refe rence: Command :ROSC:EXT :FREQ Long [:SOURce]:ROSCillator: EXTernal:FREQuency Form Set & Query Para.
70 Programming Reference SCPI Instrument Command List Command :VOL T[1] Long [:SOURce]:VOLTage[1][: LEVel][:IMMediate][:AMPLitude] Form Set & Query Parameter Num eric Parameter suffix V with engi neering p refixes. V alu e coupl ing Range co upling W ith Offset, see page 7 1 *RST value 1.
71 Programming Reference SCPI Instrume nt Command List Command :VOL T[1]:OF FSet Long [:SOURce]:VOLTage[1][: LEVel][:IMMediate]:OFFSet Form Set & Query Parameter Num eric Parameter suffix V with engi neering p refixes. V alu e coupl ing Range co upling With Amplitude, see page 70 *RST value 0.
72 Programming Reference SCPI Instrument Command List Command :VOL T[1]:HI GH Long [:SOURce]:VOLTage[1][: LEVel][:IMMediate]:HIGH Form Set & Query Parameter Num eric Parameter suffix V with engi neering p refixes. V alu e coupl ing Range co upling W ith low level, see page 73 *RST value 500 m V Specified li mits –9.
73 Programming Reference SCPI Instrume nt Command List Command :VOL T[1]:LOW Long [:SOURce]:VOLTage[1][: LEVel][:IMMediate]:LOW Form Set & Query Parameter Num eric Parameter suffix V with engi neering p refixes. V alu e coupl ing Range co upling W ith hig h level, s ee page 72 *RST value –500 mV Specified li mits –10.
74 Programming Reference SCPI Instrument Command List Command :VOL T[1]:LIM Long [:SOURce]:VOLTage[1]:L IMit[:HIGH] Form Set & Query Parameter Num eric Parameter suffix V with engi neering p refixes. *RST value +500 mV Description Use this co mmand to set/read the high level vo ltage li mit.
75 Programming Reference SCPI Instrume nt Command List Command :VOL T[1]:LIM:ST A T Long [:SOURce]:VOLTage[1]:L IMit:STATe Form Set & Query Parameter ON | OFF | 1 | 0 *RST value OFF Description Use this co mmand to switch the outpu t limits on or off .
76 Programming Reference SCPI Instrument Command List Command :ST A T us:PRESet Long :STATus:PRESet Form Even t *RST value Not Applica ble Description This co mmand • Clears a ll status g roup event.
77 Programming Reference SCPI Instrume nt Command List 1. :STATus:QUEStionable [:EVENt]? 2. :STATus:QUEStionable:CONDition? 3. :STATus:QUEStionable:ENABle 4.
78 Programming Reference SCPI Instrument Command List Command :SYST :CHEC Long :SYSTem:CHECk[:ALL][:S TATe] Form Set & Query Parameter OF F | ON *RST value ON Description Use this command to swit ch the instrume nt’ s err or checking on or off.
79 Programming Reference SCPI Instrume nt Command List The ab ove messa ge is an example of a c ustomiz ed descri ption. Generi c descri ptions a re avail able in the SCPI 19 95 Comm and Refer ence, i tems 21.8.4 to 2 1.8.11. For mo re det ailed inf ormatio n in t he 81110A error .
80 Programming Reference SCPI Instrument Command List Description In q uery form , this c ommand reads the l ast key pressed. The buffer is emptie d by *RST and retur ns the value –1 when em pty . In set form , the comman d simulates pre ssing a key on the front panel.
81 Programming Reference SCPI Instrume nt Command List • In remote m ode only th e softkeys b elow the display and the S HIFT (LOCAL ) key ar e active . Becau se the ins trumen t normall y switches to remot e mode when any c omman d is re ceived , incl uding :SYSTe m:KE Y , simulating one of t he other disabled key s has no effect.
82 Programming Reference SCPI Instrument Command List Command :S YST :SE C Long :SYSTem:SECurity[:STAT e] Form Set & Query Parameter ON |OFF *RST value OF F Description CAUT ION Do not swit ch on sy stem s ecurit y unle ss yo u are wil ling to erase the instrument settings stored in the instrument.
83 Programming Reference SCPI Instrume nt Command List Command :S YST:SE T Long :SYSTem:SET Form Set & Query Parameter Bl ock data *RST value Not ap plicable Description In query f orm, th e comm and rea ds a bloc k of data contai ning the instrument ’ s complete setup .
84 Programming Reference SCPI Instrument Command List Command :SYST :W ARN:STR? Long :SYSTem:WARNing:STRing ? Form Query *RST value Not ap plicable Description Use th is command to read all the curr ently act ive warning me ssages. The warnin g messages are concat enated to form a singl e string with a “;” as separator between t he messages.
85 Programming Reference SCPI Instrume nt Command List Exam ples T o set u p a trigge red bu rst of 1 6 Sing le Pulses a t Out1, each bu rst trigg ered by a positive edge at the EXT IN PUT : T o set u.
86 Programming Reference SCPI Instrument Command List Command :TRIG:LEV Long :TRIGger:LEVel Form Set & Query Parameter Num eric Parameter Suffix V with enginee ring prefix es. *RST value 1. 0 V Specified Lim its –10 V to +10 V Description Use this comman d to program the trig gering th reshold o f the CLK- IN connect or .
87 Programming Reference SCPI Instrume nt Command List Pulse period sources set by :TRIG:S OUR Pulse per iod source :T RIG:SO URce internal osc internal PLL CLK-IN IMMedi ate INTern al[1] INTern al2 E.
88 Programming Reference SCPI Instrument Command List.
89 3 3 Specifications In this chapter you wi ll find th e speci fication s of the Agilent 81101A Pulse Generator . At the end of this ch apte r , “Pulse Parameter Definitions” on page 105 provides detailed info rmation on the d efinition of the pulse para meters used by the instrum ent.
90 Specifications Declar ation of Conformi ty Declaration of Conform ity Manufact urer Agilent T ec hnologies Deutschland GmbH Boeblingen V erification Solutions Herrenberger Str .
91 Specifications Agilent 81101A Spec ifications Agilent 81101A Specifications General Environment al Conditions Safety IEC1010 , CSA101 0 Power requirem ents 100–240 V ac, ± 10%, 5 0–60 Hz; 100–120 V ac, ± 10% , 400 Hz Power co nsumption: 300 V A max.
92 Specifications Agilent 81101A Specifications W eight Net 8.5 kg Single Channel 9.2 kg D ual Ch annel Ship ping 13.8 kg Dual Cha nnel Recalibra tion period 1 yea r reco mmend ed W arranty 3 years st.
93 Specifications Agilent 81101A Spec ifications T iming Specification s Period Period can al so be e ntered as freq uency . There a re 2 pe riod gen eration source s availab le: • startable oscilla.
94 Specifications Agilent 81101A Specifications Wi d t h Can be ent ered as absolu te width, duty cycle or trailing ed ge delay . Duty cyc le val ues from 0.1% to 95% can be ente red dir ectly . For valu es >95 % press SHIF T and use the Modif y knob.
95 Specifications Agilent 81101A Spec ifications Double Pulse Delay Double pulse delay an d delay are mutually exclusive. Doub le Pulse delay is the delay between the tw o pulses in Double Pu lse mo de. T ransition T imes Measure d between 10% and 90% o f amplitude.
96 Specifications Agilent 81101A Specifications Leading an d trailing edges can b e programme d independent ly within the follo wing ra nges ( Maximum ratio 1:20): Level Spec ifications Externa l Load comp ensation For loads ≠ 50 Ω , the actual load imp edance can be ente red to c orrect the output v alues.
97 Specifications Agilent 81101A Spec ifications Level Pa rameter s Level para meters ca n be enter ed as high/l ow level in ter ms of voltag e or curr ent or offs et/a mpli tude . Pulse Performance Clock Sourc es It is possible to sele ct between thr ee clock sour ces, the startable oscillator (VFO) , the internal PLL, or the External Clock.
98 Specifications Agilent 81101A Specifications Clock / PLL Reference Input Rear p anel BN C connect or used as: • Exte rnal sy stem cl ock i nput: pu lse fre quency = inp ut freq uency. The inp ut frequ ency ca n be me asured. • 5 MHz or 10 M Hz frequenc y referenc e input for in ternal PLL.
99 Specifications Agilent 81101A Spec ifications External Clo ck • The output pe riod is determine d by the signal a t clock input. Freque ncy a ccuracy can be increased by usi ng a pr ecise ex ternal clock. • Trigger synchr onously to externa l clock: the out put period is synchr onous to the signa l at cloc k inpu t.
100 Specifications Agilent 81101A Specifications T rigger Modes Continuous Generate co ntinuous pu lses, double pulses, or bursts. Exte rnal ly T rigge red Each activ e input transition (risin g, falling or bo th) triggers a single pulse, a doub le pulse, or a b urst.
101 Specifications Agilent 81101A Spec ifications T rigger and Strobe Specifications T rigger Output Strobe Out put T rigger Output Sp ecifications Agilent 81101A Level: TTL or ECL sel ectable Output .
102 Specifications Agilent 81101A Specifications T ypi ca l Delay s Mode f rom to typ. value Extern al W idth Ext Input Strob e/T rigge r Out OUTPUT 8.5 ns 22.5 ns T rigger Gat ed Ext Inpu t Strobe/T ri gger Out OUTPUT 12.0 ns 29.0 ns Conti nuous St robe/ T rigger Out OUTPUT 17.
103 Specifications Agilent 81101A Spec ifications Human Int erface Overprog ramming Parame ter val ues can be entered exceedi ng the spec ified r ange. W arnings and Errors W arnin g messages indi cate pote ntially conf licting par ameters due t o accur acy toleran ces.
104 Specifications Agilent 81101A Specifications Remote Control Operate s accord ing to IE EE standar d 488.2, 1987 and S CPI 1992.0 . Func tion C ode SH1, AH1, T 6, L4, SR1, RL1, P P0, DC1, DT 1,C0. Programming T imes (all checks and disp lay off). Command T ypica l execut ion ti me One param eter or mode 30 ms typ.
105 Specifications Pulse Parameter Definiti ons Pulse Parameter Definitions Here you f ind th e pul se par amet er def init ions o f term s used in th e instru ment spec ificat ions .
106 Specifications Pulse Paramete r Definitions T ime R eference Point The time r eference po int is at the median of the a mplitude (50% amplit ude p oint on p ulse ed ge): Pulse Period The ti me int.
107 Specifications Pulse Parameter Definiti ons practice, st art points may shift wit h changes in tran sition time ) when transition times are varied.
108 Specifications Pulse Paramete r Definitions T ransition T ime Interv al between the 10% and 90% a mplitu de points o n the lea ding/ trailing edge : Linearity Peak d eviation o f an ed ge from a s.
109 Specifications Pulse Parameter Definiti ons Jitte r Short-term inst ability of one ed ge relative to a refer ence edge. Usually specif ied as rms val ue, whic h is on e standar d deviatio n or “ sigma”. If distribution is assumed Gaussian, six sigma represents 99.
110 Specifications Pulse Paramete r Definitions Preshoot, Ov ershoot, R inging Preshoo t and overshoot ar e peak distor tions precedin g/follow ing an edge. Rin ging is the positive-pe ak and nega tive-p eak distort ion, excludin g overshoot , on pulse top o r base.
111 Specifications Pulse Parameter Definiti ons Repeat ability When an i nstrument operate s under th e same e nvironmen tal co ndition s and with the same settings, the value of a parame ter will lie withi n a band inside the accuracy w indow . Repeatabilit y defines the width of this band .
112 Specifications Pulse Paramete r Definitions.
113 Index Symbols % of Per 57 , 58 A Acoustic Noise Emission 92 Amplitude curren t 48 definition 109 voltage 70 B Burst length 84 mode 84 C Cert ifica tion met sp ecificat ions 5 Clear Error Queue 76 .
114 Index J Jitter definition 109 K Key-Code Re ference 80 L Last Key Pres sed 79 Leading Ed ge comma nd 65 definition 108 Linearity definition 108 List of Commands 26 Load File in to me mory ’n ’.
115 Index S Safety symbols 8 SCPI Command Dictionary 38 Versio n 83 Setting loa d int o memor y ’n’ 46 Settling Time definition 110 Simulatin g Key Presse s 79 Skew definition 107 Specifications 8.
116 Index.
7 4 8 9 5 6 123 O . +/- nano micro Mega milli kilo ENTER MAN STORE HELP SHIFT DATA ENTRY CURSOR/ DIGIT MODIFY LOCAL AUTOSET RECALL PERIOD DELAY WIDTH LEAD TRAIL HIGH LO W ON | OFF KNOB CURSOR Keys ENT.
Copyright Agilen t T ech nologies 1998 , 2000 Edition E0300 Printed in Germany 81101-9102 1.
MANUAL CHANGES September, 01 Manual for Model Number 81101A Manual printed on März 2000 E0300 Manual Part Number 81101-91021 5 September, 2001 Page 1 of 4 Make all ERRATA corrections.
MODEL 81101A ____________________________________________________________________ __________________________________________________________________________________ 05.
MODEL 81101A ____________________________________________________________________ __________________________________________________________________________________ 05.
MODEL 81101A ____________________________________________________________________ __________________________________________________________________________________ 05.
DECLA RA TION OF CONFORMITY According to ISO /IEC G uide 22 and CEN/CENELEC EN 45014 Revision: C I ssue Date: 2001-May -02 Manufactur er’s Name: Agilent Technol ogie s Deutschland Gm bH Manufactur er’s A ddress: Boeblingen Ver ificati ons Solut ions (BVS) Herrenber ger Str.
デバイスAgilent Technologies 81101Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Agilent Technologies 81101Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAgilent Technologies 81101Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Agilent Technologies 81101Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Agilent Technologies 81101Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Agilent Technologies 81101Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAgilent Technologies 81101Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Agilent Technologies 81101Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAgilent Technologies 81101Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。