CorneliusメーカーUC 700 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 35
IMPORT ANT : TO THE INST ALLER. It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A1 12.1.2-1979; or an approved vacuum breaker or other such method as proved effective by test.
i 630460127 T ABLE OF CONTENTS Page SAFETY INFORMA TION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RECOGNIZE SAFETY INFORMA TION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii 630460127 T ABLE OF CONTENTS (cont ’ d) Page UPPER NUT AND BEARING ASSEMBL Y 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TO REPLACE BEARING 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 6630460127 SAFETY INFORMA TION Recognize Safety Information This is the safety-alert symbol. When you see this symbol on our machine or in this manual, be alert to the potentially of personal injury . Follow recommended precautions and safe operating practices.
2 630460127 THIS P AGE LEFT BLANK INTENTIONALL Y.
3 630460127 GENERAL DESCRIPTION T O THE USER OF THIS MANUAL This manual covers the installation and assembly of the Air – Cooled or W ater – Cooled Model UC700 Icemaker with the Model UC150 Dispenser .
4 630460127 T able 1. Design Data (cont ’ d) W ater Supply – W ater inlet fitting is 1/4 – inch SAE flare located at the top front of the Unit. The Unit is designed to operate on water pressure between 10 PSI and 90 PSI.
5 630460127 FIGURE 1. CLEARANCE REQUIREMENTS.
6 630460127 THIS P AGE LEFT BLANK INTENTIONALL Y.
7 630460127 INST ALLA TION PRE – INST ALLA TION Freight Damage Claim The delivery of your equipment (Frieght Company , Distributor , or dealer) is responsible for loss or damage of your shipment. All claims must be filed with the deliverer of your equipment.
8 630460127 INST ALLA TION 1. Keep unit in the upright position, remove carton and pallet from the Icemaker and inspect for damage. If any damage is found, file a claim with carrier immediately . 2. Locate startup card either on outside of container or on plastic liner .
9 630460127 INITIAL ST ART UP , CHECKS AND ADJUSTMENT INSTRUCTIONS NOTE: Do not start Icemaker before completing installation steps on pages 7 and 9. T urn on water supply (if Icemaker is water cooled.
10 630460127 THIS P AGE LEFT BLANK INTENTIONALL Y.
11 630460127 GUIDE T O SER VICE W ARNING: Disconnect electrical power to the Icemaker to prevent personal injury before attempting any internal maintenance. Only qualified personnel should service internal components or electrical wiring. ICEMAKER CLEANING AND SANITIZING PROCEDURES Do not use any of the ice made during cleaning operations.
12 630460127 Semi – Annually Semi-Annually in addition to all previously established service procedures perform the following: 1. Check for water leaks in tube connections, water fittings and lower Icemaker water seal. 2. Check drain tubes for clogs and aged tubes.
13 630460127 3. The transparent bowl not only provides a visible check of water level, but also is a good guide to the inter- nal conditions which exist within the icemaker assembly itself. (See Cleaning Procedure.) T o Replace W ater Level Control 1.
14 630460127 EXP ANSION V AL VE Y ou will find a thermostatic expansion valve on icemakers, which is used to control the amount of refrigerant flowing through the evaporator . Improperly installed or defective expansion valves may cause low production, soft ice, squeaking from evaporator and excessive load inside evaporator .
15 630460127 FIGURE 5. EXP ANSION V AL VE FIGURE 6. ADJUSTMENT SCREW THERMOST A TIC EXP ANSION V AL VE SIGHT GLASS CONDENSER MODULA TING V AL VE REMOV AL 1. Disconnect power to unit, then shut off water supply to condenser and evacuate refrigerant from system.
16 630460127 GEARMOT OR The gearmotor is equipped with a start relay and a manual reset overload. When current is applied, the relay energizes and completes the circuit to the start winding. The motor reaches a predetermined speed and the relay drops out, disconnecting the start winding.
17 630460127 ST ART RELA Y 1. Check between “ 2 ” and “ 4 ” on relay (with relay unplugged). If there is continuity replace the relay , as the relay contacts should be open. 2. Check between “ 3 ” and “ 4 ” on relay , if no continuity replace the relay .
18 630460127 AUGER AND EXTRUDING HEAD REMOV AL 1. Disconnect unit from power supply . 2. Remove storage container cover and put aside. 3. T urn off water supply to icemaker . 4. After ice has melted from head take hold of the auger nut and lift straight up to disengage from icemaker .
19 630460127 3. Remove Dispense T ray Cover . 4. Use an open end wrench on auger nut connected to bearing and turn counterclockwise to remove assembly . 5. Remove worn bearings. Replace with new bearings and then reinstall assembly . NOTE: If auger turns with nut, remove cover on top of gearmotor stator and hold motor while loosen- ing nut.
20 630460127 FIGURE 12. GEAR MOTOR OVERLOAD SAFETY CONTROLS Y our icemaker unit has several safety and control devices incorporated into its design. W ARNING: None of the below described devices should ever be “ bypassed ” to allow the unit to function.
21 630460127 GUIDE TO GOOD ICE CUSTOMER COMMENTS CHECK ICEMAKER LOCA TION CONDITIONS FIRST CHECK ICE MAKER S Use gauges for checking suction and head pressures. See manual for correct reading and conditions. Check frost line and sight glass. S Check water level for proper adjustment and restrictions.
22 630460127 FIGURE 13. WIRING DIAGRAM.
23 630460127 TROUBLESHOOTING CHART – ICEMAKER NOT OPERA TING NO POWER Check electrical wiring in con- trol box for loose connec- tions. Check for failed service switch or relay . Check power to machine. ICEMAKER RUNS BUT DOES NOT MAKE ICE Condenser fan running but compressor not running Check line voltage.
24 630460127 TROUBLESHOOTING IMPORTANT : Only qualified personnel should service internal components or electrical wiring. TROUBLESHOOTING COMPRESSORS T rouble Probable Cause Remedy Basically the compressor problems can be narrowed down to three areas of checkout.
630460127 25 P ARTS LIST.
26 630460127 FIGURE 14. P ANEL COMPONENTS 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 1 1 20 Item No. Part No. Name 1 07578 Thread Cutting Screw , Phil T russ Hd, No.
630460127 27 Item No. Part No. Name Ice Chute Components 1 38220 Machine Screw , 1/4-20 2 630000741 Elbow , Ice Chute 3 630250106 T ube, Ice Transfer 4 630900564 O-Ring, 4.234 I.D. 5 630900608 Head, Extruder 6 638090213 Auger 7 638090219 Bearing, Nylon 8 638090220 Bearing, Delrin 9 63809021 1-002 Auger Nut 1 2 3 4 5 6 7 8 9 FIGURE 15.
28 630460127 Item No. Part No. Name Compressor Com ponents 1 164154001 Washer , Flat, >375 I.D. 2 165596002 Grommet 3 168770002 Machine Screw , Hex Hd, 5/16-18 By 1 1/2-In. Long 4 631500018 Compressor Kit 5 638007972-02 Hex Washer Hd, No. 10 By 1/2-In.
630460127 29 Item No. Part No. Name Evaporator Com ponents 1 630200737 Bracket 2 630900558 Adaptor , Front End Ass ’ y 3 630900559 Gasket, Front End Ass ’ y 4 630900572 O-Ring, 4.1 I.D. 5 630900635 Machine Screw , Hex Hd, 1/4-20 By 1 3/4-In. Long 6 638001662 Insulator , Switch 7 638003924 Switch 8 638007009-10 Screw , No.
30 630460127 IMI CORNELIUS CER TIFICA TE OF W ARRANTY TWO YEAR LIMITED ICE EQUIPMENT W ARRANTY IMI Cornelius warranty to the original commercial purchaser/user , that any commercial product of its man.
31 630460127 THIS P AGE LEFT BLANK INTENTIONALL Y.
One Cornelius Place Anoka, Minnesota 55303-6234 T elephone (800) 238-3600 Facsimile (763) 422-3246 Corporate Headquarters: IMI CORNELIUS INC..
デバイスCornelius UC 700 Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cornelius UC 700 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCornelius UC 700 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cornelius UC 700 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cornelius UC 700 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cornelius UC 700 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCornelius UC 700 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cornelius UC 700 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCornelius UC 700 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
