Craftsmanメーカー113.24181の使用説明書/サービス説明書
ページ先へ移動 of 40
owners manual MODEL NO. 113.24181 7 Serial Number ................................ Model and serial number may be found at the rear of the base. You should record both model and serial number in a safe place for futu re use.
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWS If within one year from the date of purchase, this Craftsman Table Sae fails due to a defect in material or workmanship, Sears will repair it, free of charge. Warranty service is available by simply contacting the nearest Sears store or Service Center throughout the United States.
ADDiTiONAL SAFETY iNSTRUCTiONS FOR TABLE SAWS WARNING: FOR YOUR OWN SAFETY, DO NOT OPERATE YOUR SAW UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS ... AND UNTIL YOU HAVE READ AND UNDERSTOOD THE FOLLOWING. 1. 2, 3. 4. 5. 6.
B. Never use grinding wheels, abrasive cut-off wheels, friction wheels (metal slitting blades) wire wheels or buffing wheels. 11. USE ONLY ACCESSORIES DESIGNED FOR THIS SAW. 12. Cross-cutting operations are more conveniently worked and with greater safety if an auxiliary wood facing is attached to the miter gauge using the holes provided.
the supply circuit) or when the supply circuit is extremely long. Always check connections, load and supply circuit when the motor fails to perform satisfactorily. Check wire sizes and lengths with the table in the next paragraph. Replace or repair damaged or worn cord immediately.
UNPACKING AND CHECKING CONTENTS TOOLS NEEDED , P, iers @ @ Wrenches :iii! ?i i: i ii iiii:!iii i;l 3/8 in. 7/16 in. 1/2 in. 9/16 in. Combination Square 3/4 in. Model 113.24181 Motorized Table Saw is shipped complete in one carton including Two Table Extensions and Steel Legs.
ASSEMBLY ATTACHgNG LEGS 1. Turn the saw upside down. NOTE: DO NOT LAY IT ON THE FLOOR AS THIS MAY SCRATCH THE TABLE SURFACE. PLACE IT ON STRIPS OF WOOD OR PARTS OF THE PACKING MATERIAL. 2. From among the loose parts, find the following hardware: 16 Hex.
Insert forefinger into table-insert slot and pull upward to remove insert. Replace insert. If clips do not hold insert securely, remove insert and bend clips. SPRING CLIP BEND CLIPS AS NEEDED SPRING CLIP CHECKING BLADE SQUARENESS TO TABLE 1. Loosen ELEVATION LOCK by pulling KNOB forward.
Lay REAR FENCE GUIDE BAR on table to act as a straightedge. If outer edge of extension is higher or lower than table surface; A. Slightly loosen nuts holding bracket to extension using 7/t6 in. wrench. B. Move end of extension up or down until outer edge is even with table surface .
9. Hold rod with one hand and with a 7/16 in. wrench or pliers start screwing on ONE of the nuts only ATURN OR TWO ... screw on other nut the same way. 10. Using TWO 7/16 in. wrenches or pliers tighten both of the nuts. 11. Slide the bars so that screws are in the MIDDLE of the slotted holes.
ALIGNING RIP FENCE The fence should slide easily along the bars and always remain in alignment (parallel to sawblade and miter gauge grooves). The alignment is maintained by a spring underneath the fence which bears against the front guide bar. To move the fence, loosen the lock handle and grasp the fence with one hand at the front.
If the fence does not slide easily along the bars, the pressure of the spring can be REDUCED. 1. Loosen the screws. 2. Move spring slightly toward rear of fence . . . tighten screw_ 3. The rip fence must be PARALLEL with the sawblade and Miter Gauge grooves .
3. SHde support onto SUPPORT ROD until PIN in rod fits into notch in support ... insert THUMB SCREW and tighten it. 4. Loosen setscrew in end of SPREADER BAR using 5/32 in. setscrew wrench. 5. Slide guard to right until end of rod is even withbar. 6. Make sure blade is square to table and raised as high as it will go.
G ETTING TO RN OW YOUR 6 11 8 BLADE GUARD 7 MITER GAUGE SAW 0 SAWBLADE ON-OFF SWITCH TABLE INSERT i TILT LOCK KNOB ELEVATION LOCK HANDLE ELEVATION CRANK 1 ON-OFF SWITCH CAUTION: Before turning switch on, make sure the blade guard is correctly installed and operating properly.
2 ELEVATION CRANK . . . elevates or IoweFs the blade. Turn clockwise to elevate ... counterclockwise to lower. 3 ELEVATION LOCK . •. locks the blade at the desired height. PUSH in to LOCK... PULL out to unlock. 4 TILT CRANK ... tilts the blade for bevel cutting.
|0 REMOVING AND INSTALLING SAWBLADE WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR INSTALLING SAWBLADE. A. Remove insert. B. Place ARBOR wrench on fiat surfaces of saw ARBOR ... ARBOR NUT wrench on nut .
BASIC SAW OPERATION USING THE MITER GAUGE CROSSCUTTING, MITER CUTTING, BEVEL CUTTING, COMPOUND MITER CUTTING and when RABBETING across the end of a narrow workpiece, THE MITER GAUGE IS USED. WARNING: FOR YOUR OWN SAFETY, ALWAYS OBSERVE THE FOLLOWING SAFETY PRECAUTIONS iN ADDITION TO THE SAFETY iNSTRUCTIONS ON PAGES 2, 3, and 4.
CROSSCUTTING CROSSCUTTING is known as cutting wood across the grain, at 90 ° , or square with both the edge and the flat side of the wood. This is done with miter gauge set at "0". The graduations on the miter gauge provide accuracy for average woodworking.
1. NEVER USE THE RIP FENCE AS A LENGTH STOP BECAUSE THE CUTOFF PIECE COULD BIND BETWEEN THE FENCE AND THE BLADE CAUSING A KICKBACK. 2. When making repetitive cuts shorter than 6 in., clamp a block of wood 3 in. long to the table to act as a length stop.
USING THE RiP FENCE RIPPING, BEVEL RIPPING, RESAWING AND RABBETING are performed using the RIP FENCE together with the AUXILIARY FENCE/WORK SUPPORT, PUSH STICK OR PUSH BLOCK. WARNING: FOR YOUR OWN SAFETY, ALWAYS OBSERVE THE FOLLOWING SAFETY PRECAUTIONS IN ADDITION TO THE SAFETY INSTRUCTIONS ON PAGES 2, 3, and 4.
When "WIDTH OF RIP" is 2 in. to 6 in. wide USE THE PUSH STICK to feed the work. ! ! I / When WIDTH OF RIP is NARROWER than 2 in., the push stick CANNOT be used because the guard will interfere ... USE the AUXILIARY FENCE/WORK SUPPORT and PUSH BLOCK.
RESAWING RESAWING is known as ripping a piece of wood through its thickness. NOTE: To RESAW a piece of wood wider than 3-9/16 in .... it will be necessary to remove the blade guard ... and use the AUXILIARY FENCE/WORK SUPPORT. (See "Work Helpers").
ADJUSTMENTS WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS• MITER GAUGE NOTE: The holes for the stop pin and the gra.
If tooth does not touch the same amount ... the mechanism underneath must be adjusted to make the blade PARALLEL to GROOVE. NOTE: Make sure TILT CLAMP KNOB is tightened. 1. Lay the saw on its LEFT SIDE. 2. Loosen Hex. Head screw "A" between 1/4 and 1/2 turn, using a 5/8 in.
If blade IS SQUARE to table; A. Check pointer If POINTER DOES NOT point to the "0" mark on the bevel scale; B. Loosen screw and adjust pointer ... using medium screwdriver. If blade is NOT SQUARE to table.., the90 ° stop screw must be ADJUSTED.
ELEVATION LOCK When correctly adjusted, the elevation mechanism is locked securely when the ELEVATION LOCK KNOB is approx. one inch from the front of the saw. After extended use, the ELEVATION LOCK SCREW and NUT may wear, which will cause the lock to slip.
LUBRICATION The saw motor bearings have been packed at the factory with proper lubricant and require no additional lubrication. 1. Lay the saw on its LEFT SIDE. 2. Clean the following parts with Craftsman Gum and Pitch Remover; BEVEL GEARS, ELEVATION WORM AND TEETH, TILT WORM AND TEETH.
TROUBLE SHOOTING WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLESHOOTING. TROUBLE SHOOTING -- GENERAL TROUBLE PROBABLE CAUSE REMEDY Excessive vibration. 1. Discard Blade and use a different blade.
TROUBLE SHOOTING -- MOTOR (Continued) TROUBLE PROBABLE CAUSE Motor starts slowly or fails to come up to full speed. Motor overheats. Starting relay in motor will not operate. Motor stalls (resulting in blown fuses or tripped circu it breakers). Frequent opening of fuses or circuit breakers.
PARTS LIST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 o 4 29 15 28 6 10 12 t I t I ,21 23 I I 20 m "0 m Figure 1.
PARTS LIST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 Always order by Part Number - not by Key Number FIGURE 1 PARTS LIST w Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Part No. STD 541025 STD 551225 STD 522506 62594 STD 523108 62541 STD 501102 62403 62474 803938 62584 62493 60122 STD 541031 STD 551231 62539 Description i.
PARTS LIST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 3 2 / ........_ 66 _----_ 67 68 -'-" 69 4 5 24 20 21 Figure 2 28 50A 51 52 58 57 ' _.
Key No. PARTS LiST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 FIGURE 2 PARTS LiST Part No. 62459 30494 60177 6362 3540 63062 STD 600803 30613 STD 582075 62342 62340 62339 STD 551.
PARTS LIST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 7 1 I FIGURE 3 - 62581 FENCE ASSEMBLY Key Part No. No. m 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 62581 62524 STD 551031 62534 60049 62527 423350 62582 STD611005 62528 62529 62531 62583 62533 STD 551210 62532 STD 600805 Description Fence Assembly, Rip Handle *Washer, 21/64 I.
PARTS LIST FOR (;RAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 3 4 TO SWITCH ® ANY ATTEMPT TO REPAIR THIS MOTOR MAY CREATE A HAZARD UNLESS REPAIR IS DONE BY QUALI FlED SERVICE TECHNICIAN. REPAIR SERVICE IS AVAILABLE AT YOUR NEAREST SEARS STORE.
PARTS LiST FOR CRAFTSMAN 12-iNCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 I _ _--- 7 9 --------_ _-J"_--'--" 8 13 I TO MOTOR_ 12 11 9 3 4 5 SEE WIRING DIAGRAM, PAGE 5 FIGURE 5 -- SWITCH ASSEMBLY (DOMESTIC) Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No.
PARTS LIST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 8 FIGURE 6- 62325 MITER GAUGE ASSEMBLY Key Part No. No. - 62325 1 62524 2 STD 551031 3 37893 _ STD 600803 135 6 37895 7 3789.
PARTS LIST FOR CRAFTSMAN 12-! NCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 1 2 3 / / / / / LI 12 5 | 8 7 9 6 FIGURE 7 -- 62594 GUARD ASSEMBLY Key No.
PARTS LIST FOR CRAFTSMAN 12-INCH MOTORIZED TABLE SAW MODEL NUMBER 113.24181 ! 4 7 FIGURE 8 -- 62589 TABLE EXTENSION Key Part No. No. Description -- 62589 1 60323 2 3 4 5 6 7 62590 62549 62548 STD 541025 STD 551225 62550 Extension Assembly, Complete Screw, Serrated Truss Hd.
Sears SERVICE MODEL NO. 113.24181 HOW TO ORDER REPAIR PARTS 12 iNCH MOTORIZED TAB LE SAW Now that you have purchased your 12-inch table saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
デバイスCraftsman 113.24181の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 113.24181をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 113.24181の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 113.24181の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 113.24181で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 113.24181を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 113.24181の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 113.24181に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 113.24181デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
