Craftsmanメーカー247.77588Oの使用説明書/サービス説明書
ページ先へ移動 of 26
Owner's Manual CRAFTSMAN 8.5 Horse Power CHIPPER-SHREDDER Model No. 247.77588O CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. 770-1228A Printed in U.
Content Page Content Page Warranty Information 2 Service & Adjustment 14 Safe Operation Practices 3 Off-Season Storage 16 Assembly 5 Trouble-Shooting 17 Operation 8 Repair Parts 18 Maintenance 11 .
This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper shredder.
impeller tocome toa complete stop. The impeller continues torotate for a few seconds after the engine is shut off. Never place any part of the body in the impeller area untilyou are sure the impeller has stopped rotating. Muffler and engine become hot and can cause a bum.
Hopper* Chipper Chute Discharge Chute Bottle of Oil Safety Glasses Catcher Bag * The hopper is packed in the top insert in your chipper-shredder carton. Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine, Al_er assembly, see OPERATION section of this manual for proper fuel and engine oil fill-up.
through hinge on discharge chute and housing (spacer fits inside of hinge). See figure 3 inset. Spac_er _-J-_ Hex Nut --Hex Bolt Hinge Hopper Pivot Door Inlet Guide Opening He_ Hopper Nut Wing Dischargl Figure 3 Place second spacer over hex bolt inside the other part of the hinge.
& WARNING; This flap control rod is a safety device to hold the flap in place inside the hopper while shredding branches. Do not operate the chipper-shredder without properly attachingthis flap control rod to the unit.
Read this owner's manual and safety rules before operating your chipper-shredder. Compare the illustration in figure 9 with your chipper-shredder to familiarize yourselfwith the location of various controls and adjustments. Save this manual for future reference.
WARNING: Before using yourchipper- shredder, again refer to the safety rules on pages 3 and 4 of this manual. Always be careful. GAS AND OIL FILL-UP Oil (Packed with unit) Only use high quality detergent oil rated with API service classification SF, SG or SH.
NOTE: TO prevent the unit fromsliding, place your foot firmly against the tire. 1. Attach spark plug wire -- 3. Move choke to "on" position 2. Place throttle in Fast Position 4. Pull rope Figure 1t Attach spark plug wire and rubber boot to spark plug.
changes (becomes stdngy, etc.) or if the rate at which the material is discharged slows down considerably, it is likely that the shredding blade and/or chipper blades are dull and need to be sharpened or replaced. Refer to Service and Adjustments section.
CUSTOMER RESPONSIBILITIES o MAINTENANCE _ _ ..,P e,_P _3 =_ sc. oo, o,O { o ,v.C o,TEs Oil pivot points 0 Clean shredder _ a. Check engine oil ,,, Change engine oil <_ Service air cleaner ILl Clean engine _ Reset spark plug _ Clean muffler operatingtemperature.
If necessary, replace paper filter (do not attempt to clean). Installnew filter on base. Slide pre-cleaner over filter. Install cover and wing nut. Tighten wing nut securely. Clean Engine Clean engine periodically. Remove dirt and debris with a cloth or brush.
14.
REMOVING THE FLAIL SCREEN If the discharge area becomes clogged, remove the flail screen and clean area as follows. Stop engine, make certain the chipper- shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute.
Disconnect spark plug wire and move it away from spark plug. Lower the hopper assembly. Block up the housing. See figure 19. Weld Bolt Allen Screw Pipe cause damage to the unit.The blade can be tasted for balance by balancing it on a round shaft screwddver or nail.
Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. A WARNING: Never store machine with fuel in the fuel tank inside of building whe.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Engine fails to start 1. Fuel tank empty, orstale fuel 1. Fill tank with clean, fresh fuel 2. Spark plug wire disconnected 2. Connect wire to spark plug. 3. Faulty spark plug 3. Clean, adjust gap or replace. 4.
SEARS CRAFTSMAN 8.5 H.P. CHIPPER-SHREDDER MODEL 247.775880 6 29 12 21 5 14 18 97 33 13 74 52 56 85 88 63 65 80 79 91 19.
Key Part No No -- 770-1228A 1 11480 2 681-0118 3 681-0144 4 710-0542 710-0607 710-3256 7 712-0429 8 712-3027 9 714-0104 10 715-0129 11 726-0106 12 726-0135 13 728-0175 14 732-0546 15 732-0629 16 735-0.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 35 4OO 310 3O5 757 87 7O 69 2g0 101 1t0 182 251 21.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247,775880 Key Part No. No. -- m 1 35385 2 27652 4 5 30969 15 30699C 15A 17 18 19 20 25 26 28 30 35 38 37 38 40 40 41 41 42 .
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247,775880 Key Part No. No. 185 34707 186 34667 200 34677 203 31342 204 651029 206 610973 207 33878 209 650821 215 35882 223.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 Carburetor Key Part Description No. No. 640112 1 631776A 2 631970 4 631184 ,.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 Recoil Starter 590746 13 12 "8 6_'_6 ¢p-.4 Key Part Description No. No. 590746 1 590599A 2 590600 3 590679 4 590601 5 590678 6 590680 7 590412 8 590681 11 590747 12 590535 13 590701 Recoil Starter Spring Pin (Incl.
For the repair or replacement partsyou need delivered directlyto your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7.
デバイスCraftsman 247.77588Oの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 247.77588Oをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 247.77588Oの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 247.77588Oの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 247.77588Oで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 247.77588Oを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 247.77588Oの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 247.77588Oに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 247.77588Oデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
