Craftsmanメーカー247.795861の使用説明書/サービス説明書
ページ先へ移動 of 16
OWNER'S MANUAL MODELNOS° 247.795860 247=795861 Caution: Readand Follow All Safety Rules and Instructions Before Operating This Equipment 8 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGING CHIPPER=SHREDDER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO.
SAFETY RULES l_ PERSONAL INJURY, WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN TRAINING e Read t.
CC'NGRATULATIONS on your purchase of a Sears Crattsman Chipper-Shredder It has been designed, engi- neered and manufactured to give you the best possible dependability and performance, Should you.
TABLE OF CONTENTS ' SAFETY RULES ....................................................................... 2 PRODUCT SPECIFICATIONS ..................................... 3 WARRANTY ...................................................................
£ ASSEMBLY mNSTRUCTmONS IMPORTANT: This unit is shipped WITHOUT GASO_ LINE or OIL After assembly, see operation section of this manual for proper fuel and engine oil recommen- dation& NOTE: To determine right and left hand sides of your .
Spacers Hinge) Housing Assembly Hex Lock- Nut Hand Chute Deflector FIGURE 2. Stop Washer Upper Guide Release Assembly Bar Frame FIGURE 3. Hopper Pivot Door ASSEMBLE THIS TRUSS SCREW AND NUT FIRST Bar 8-3/8" Long Flat Washer Hex Lock Nut Hopl: Assembly Jper Guide Assembly pper Leaf Ramp Section Remove Truss Screw and Nut FIGURE 4.
e To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the draw- string, and pull on the drawstring until the bag is tight around the chute opening.
TO STOP ENGINE • Move engine shut-off switch to OFF position See figure 6 • Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. e Close fuel shut-off valve when equipment is not in use to prevent fuel leakage.
® To lower the hopper assembly, use one hand to grasp the handle at the top of the hopper assembly and lift slightly Pull up on the release bar, and lower the hopper assembly to the ground Release the bar_ See figure 10 Hopper 5/ Release Bar FIGURE 10.
Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted.
CUSTOMER RESPONSDBnLITIES MAINTENANCE SCHEDULE ,/___//_O_/ FILL IN DATES /_ ,/ _/ _ / ,_/a,,o_/^_,co/ .s REGULAR SERVICE ! / / / SERVICE ....... DATES F- Oil Pivot Points _/ O Clean Shredder q _1 rt C.
AIRCLEANER The air cleanerprevents damaging dirt, dust, etc., from entering the carburetor and being forced into the engine and is important to engine life and per- formance Never run your engine without air cleaner com- pletely assembled. To Service Air' Cleaner: Service pre-cleaner after every 25 hours of use, or at least once a season.
STORAGE ® Drain the fuel tank Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: NEVER STORE MACHINE WITH FUEL IN THE FUE.
Chute Deflector. Hairpin _ Clips, Clevis Pins --_Hex Nuts Washers Screen Chipper Chute FIGURE 19. Hand Knobs SHARPENING OR REPLACING THEBLADES CHIPPER BLADES ® Disconnect spark plug wire and move it away from spark plug e Remove the flail screen as instructed in previous section e Remove the chipper chute by removing three hex nuts and washers.
NGTE: Usecaution when removing the blade to avoid contacting the weld bolts on the housing_ e When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade.
TROUBLE SHOOTING CORRECTIVE ACTION PROBLEM POSSIBLE CAUSE(S) Engine fails to start e Fuel shut-off valve closed. e Fuel tank empty, or stale fuel. e Spark plug wire disconnected e Faulty spark plug. Loss of power; e Spark plug wire loose. operation erratic • Unit running on CHOKE e Blocked fuel line or stale fuel.
デバイスCraftsman 247.795861の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 247.795861をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 247.795861の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 247.795861の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 247.795861で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 247.795861を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 247.795861の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 247.795861に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 247.795861デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
