Craftsmanメーカー315.10833の使用説明書/サービス説明書
ページ先へ移動 of 20
Owner's Manual 7-1/4 in. CIRCULAR SAW Double Insulated Model Nos. 315.108330 315.1 O834O Save this manual for future reference A CAUTION: Read and follow all Safety Rules and Operat- ing Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co.
• Table Of Contents .......................................................................................................................................... 2 • Warranty ...........................................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
RULES FOR SAFE OPERATION (Continued) USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy duty tool. Don't use tool for purpose not intended - for example - A circular saw should never be used for cutting tree limbs or logs.
RULES FOR SAFE OPERATION (Contlnued) • USE RIP FENCE. Always use a fence or straight edge guide when ripping. SUPPORT LARGE PANELS. To minimize the risk of blade pinching and kickback, always support large panels as shown in figure 9, page 10.
Horsepower Model No. 315.108330 Model No. 315.108340 Input Model No. 315.108330 Model No. 315.108340 Blade Diameter 2 2-1/4 10 Amperes 12 Amperes 7-1/4 in. (184 mm) Blade Arbor Cutting Depth at 0 ° Bevel Cut Cutting Depth at 45 ° Bevel Cut Cutting Depth at 51.
KNOW YOUR CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive 0 ° bevel stop; length of cut scale; directed air flow for keeping line of cut clear; and blade wrench storage.
,_ WARNING: Your saw should never be connected to power supply when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Disconnecting your saw will prevent accidental starting that could cause serious personal injury.
SAW BLADES The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull blade will place a heavy load on your saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available.
TO LESSEN THE CHANCE OF KICKBACK: • Always keep the correct blade depth setting - the correct blade depth setting for all cuts should not exceed 1/4 inch below the material to be cut. See Figure 8. CORRECT BLADEDE!_'H SETTING = BLADE EXPOSED 1/4 in.
STARTING A CUT Know the right way to use your saw. See Figure 11. O TO HELP MAINTAIN CONTROL: • Always support your workpiece near the cut. • Support your workpiece so the cut will be on your right. • Clamp your workpiece so it will not move during the cut.
Hold your saw firmly with both hands. See Figure 14. TOP VIEW OF SAW OF SAW BLADE GUIDE NOTCH RIGHT Fig. 14 Squeeze the switch trigger to start your saw.
• Adjust rip guide to the length needed for the cut. • Tighten edge guide screw securely. When using a rip guide, position the face of the rip guide firmly against the edge of workpieca. This makes for a true cut without pinching the blade. The guiding edge of workplace must be straight for your cut to be straight.
POSITIVE 0 ° BEVEL STOP See Figure 19. BEVEL ADJUSTMENT WING NUT ADJUSTMENT SCREW POSITIVEO°BEVELSTOP CARPENTER'S SQUARE HEX NUT SAW BLADE Fig. 19 Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0 ° angle of your saw blade when making 90 ° cuts.
TO POCKET CUT See Figure 21. _L WARNING: Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in loss of control of your saw possibly causing serious injury.
Page 16.
,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL Only the parts shown on parts list, page nineteen, are intended to be repaired or replaced by the customer.
CRAFTSMAN CIRCULAR SAW -- MODEL NUMBERS 315.108330 / 315.108340 SEE NOTE "A" PAGE 19 23 2 3 5 27 5 11 , 12 '8 _19 13 14 15 21 20 e,.. 1617 "29 18 _ Page 18.
[ CRAFTSMAN CIRCULAR SAW -- MODEL NUMBERS 315.108330/315.108340 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CIRCULAR SAW or when ordering repair parts, SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS I PARTS LIST Key Part No.
For repair of major brand appliances in your own home... no matter who made it, no matter who sold ifl 1-800-4-MY-HOM E sM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center.
デバイスCraftsman 315.10833の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 315.10833をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 315.10833の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 315.10833の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 315.10833で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 315.10833を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 315.10833の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 315.10833に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 315.10833デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
