Craftsmanメーカー315.1152の使用説明書/サービス説明書
ページ先へ移動 of 19
Operator's Manual 3/8 in. CORDLESS DRILL-DRIVER Variable Speed / Reversible Model No. 315.115200 13.2 Volt 315.115210 15.6 Volt Save this manual for future reference ,_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product.
• Warranty .......................................................................................................................................................................... 2 • lntroducton .................................................
WARNING: READ AND UNDERSTAND ALL IN- STRUCTIONS. Failure to fo{Iow a(I {nstruct(ons {{sted be(ow, may result {n electric shock, fire and/or seri- ous personal injury. SAVE THESE INSTRUCTIONS WORK AREA • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
SERVICE • Tool service must be performed only by qualified repair personnel, Service or maintenance performed by unqualified personnel may result in a risk of injury. • When servicing a tool, use only identical replace= ment parts. Follow instructions in the Maintenance section of this manual.
WARNING: Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately.
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer.
The followingsignal words and meanings are intendedto explainthe levels of risk associated with this product, SYMBOL SIGNAL MEANING DANGER: WARNING: CAUTION: CAUTION: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
PRODUCT SPECIFICATIONS DRILL-DRIVER 315,115200 315.115210 Chuck 3/8 in. Keyless 3/8 in. Keyiess Motor 13.2 Volts 15.6 Volts Gear Train One Speed One Speed Switch Variable Speed VariabJe Speed No Load Speed 0-600imin 0-600/rain Battery 130139018 130139015 Maximum Torque 100 in.
KEYLESS CHUCK TORQUE ADJUSTMENT RING BIT STORAGE SCREWDRIVER BITS BATTERY SWITCH TRIGGER DIRECTION OF ROTATION SELECTOR (FORWARD / REVERSE) CHARGING STAND RED LIGHT CHARGER BATTERY PACK SHOWN IN TOOL WRIST STRAP Fig. 1 Instructions Your drill has been sh(pped comp(etely assembled.
_1 WARNING: Do not allow familiarity with this tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. CHARGING BATTERY PACK See Figure 1, Page 9 The battery pack for this tool has been shipped in a low charge condition to prevent possible problems.
SWITCH See Figure 2, To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. FORWARD/REVERSE/CENTER LOCK SELECTOR TO INSTALL BATTERY PACK • Lock switch trigger on this drill by placing the direction of rotation se{ector in center position.
SWITCH LOCK See Figure 4, The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position.
INSTALLING BITS See Figure 6, • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Open or close chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use.
BIT STORAGE See Figure 9, When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 9. SCREWDRIVER BITS BIT STORAGE AREA L Fig. 9 _i WARNING: Always wear safety goggles or safety glasses with side shields when operating tools.
CHUCK REMOVAL See Figures 11, 12, and 13. The chuck must be removed in order to use some acces- sories. To remove: • Lock the switch trigger by placing the direction of rota- tion selector in center position. See Figure 4. • insert a 5/16 in. or larger hex key into the chuck of your drill and tighten the chuck jaws securely.
_ WARNING: When servicing, use only identical Craftsman replacement parts, Use of any other part may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use.
17.
CRAFTSMAN 3/8in 13;2VOLT CORDLESS DRiLLeD RIVER_ M O DEL NO_3i5iii5200 _ The model number w{{I be found on a plate attached to the motor housing. A{ways mention the model | number {n all correspondence regard{ng your 3/8 in., 13.2 VOLT CORDLESS DRILL-DRIVER or when J ordering repair parts.
C RAFTSMAN 3/8in 15:6VOLT C OR D LESS D R iLL_ D RIVER_ M O D EL NO_3 i5iii52i 0 _ The model number w{{I be found on a plate attached to the motor housing. A{ways mention the model | number {n all correspondence regard{ng your 3/8 in., 15.6 VOLT CORDLESS DRILL-DRIVER or when J ordering repair parts.
デバイスCraftsman 315.1152の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 315.1152をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 315.1152の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 315.1152の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 315.1152で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 315.1152を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 315.1152の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 315.1152に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 315.1152デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
