Craftsmanメーカー315.17513の使用説明書/サービス説明書
ページ先へ移動 of 18
Owner's Manual ROUTER Double Insulated Model No. 315.175130 Save this manual for future reference CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co.
• Table Of Contents .......................................................................................................................................... 2 • Warranty ...........................................................................
The purpose of safety symbolsis to attract your attention to possibledangers. The safety symbols, and the explanations with them, deserve your carefulattentionand understanding. The safetywarningsdo not by themselves eliminate any danger. The Instructions or warnings they give are not substitutes for proper accident prevention measures.
• PROTECT YOUR HEARING, Wear hearing protection during extended periods of operation. • DO NOT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle, Keep cord from heat, oil, and sharp edges. • SECURE WORK. Use clamps or a vise to hold work.
_i WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
KNOW YOUR ROUTER See Figure I. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. SWITCH To turn your router on, depress the switch trigger.
_k WARNING: Your router should never be connected to power supply when you are assembling parts, making adjustments, installing or removing cutters, cleaning, or when not in use, Disconnecting router will prevent accidental starting that could cause serious personal injury.
DEPTH OF CUT ADJUSTMENTS See Figures 4, 5, and 6. We recommend that cuts be made at a depth not exceeding 1/8 in. and that several passes be made to reach depths of cut greater than 1/8 in. • Unplug your router. _1 WARNING: Failure to unplug your router could result in accidental starting causing serious injury.
DEPTH OF CUT ADJUSTMENTS WHEN ROUTER IS MOUNTED TO A ROUTER TABLE See Figure 7. The depth of cut is readable from both sides of the depth indicator ring. The bottom ring is convenient when using your router mounted upside down to a router table. The indicator point on the base can also be used when using your router mounted to a router table.
FREEHAND ROUTING See Figure 9. FREEHAND ROUTING Fig. 9 When used freehand, your router becomes a flexible and versatile tool. This flexibility makes it possible to easily rout signs, relief sculptures, etc. There are two basic techniques for freehand routing: • Routing letters, grooves, and patterns into wood.
TOO FAST TO0 SLOW Fig. 10 Your router is an extremely high-speed tool (25,000 RPM no-load speed), and will make clean, smooth cuts if allowed to run freely without the ovedoad of a forced (too fast) feed. Three things that cause "force feeding" are bit size, depth-of-cut, and workpiece characteristics.
To make deeper cutsit is therefore necessary to make as many successive passes as required, lowering the bit 1/8 inch for each new pass. In order to save time, do all the cutting necessary at onedepth setting, before lowering the bitfor the next pass.
STARTING AND ENDING A CUT INTERNAL ROUTING Tilt router and place on workpiece, letting edge of subbase contact workpiece first. Be careful not to let router bit contact workpiece. Turn router on and let motor build to its full speed. Gradually feed cutter into workpiece until subbase is level with workpiece.
,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer.
SWITCH REPLACEMENT See Figures 15 and 16. • Unplug your router, _k WARNING: Failure to unplug your router could result in accidental starting causing serious injury. • Remove screws (A) and handle cover (B). See Figure 15. B c .15 • Note the location of the molded bend relief (C) on the power handle cord.
CRAFTSMAN ROUTER - MODEL NUMBER 315.175130 I I 10 9 I I SEE NOTE"A" i 25 26 6_ 23 24 22 18 9 19 NOTE: "A" - The assembly shown represents an important part of the Double Insulated System. To avoid the possibility of alteration or damage to the System, service should be performed by your nearest Sears Repair Center.
CRAFTSMAN ROUTER - MODEL NUMBER 315.175130 The model number will be found on a plate attached to the motor housing. Always mention the model number | in all correspondence regarding your ROUTER or when ordering repair parts. I SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS Key Part No.
1-800-4-MY-HOME sM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night www.
デバイスCraftsman 315.17513の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 315.17513をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 315.17513の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 315.17513の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 315.17513で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 315.17513を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 315.17513の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 315.17513に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 315.17513デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
