Craftsmanメーカー315.21636の使用説明書/サービス説明書
ページ先へ移動 of 26
Owner's Manual 16 in. variablespeed SCROLL SAW Model No. 315.216360 Save this manual for future reference. A, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
• Table of Contents ........................................................................................................................................... 2 • Warranty and Introduction .........................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding.
RULES FOR SAFE OPERATION (Continued) USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
RULES FOR SAFE OPERATION (Continued) KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool. A LARGE PIECE OF MATERIAL SHOULD BE SUPPORTED while cutting.
EXTENSION CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a consider- able distance from the power source, use an exten- sion cord heavy enough to carry the current that the tool will draw.
Bevel Cut A cutting operation made with the table at any angle other than 90 ° to the blade. Crosscut A cutting or shaping operation made across the grain of the workpiece. Compound Cut A compound cut is a cut made using a miter angle and a bevel angle at the same time.
_lj WARNING: To prevent accidental starting or electrical shock that could cause possible serious personal injury, assemble all parts to your saw before connecting it to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, lubricating, installing or removing.
The following labels are on the scroll saw with locations indicated. WARNING ON OFF a CRRFTSMRN ° Consumer Help Line 1-800-932-3188 WARNING / ADVERTENCIA Fig.
This versatile variable speed scroll saw isgreat for making toys, puzzles, games, artwork, and jewelry. It is a handy do-it-yourself tool. It cuts wood, wood composition products, plastic, and other fibrous material up to2 inches thick. It also cuts nonferrous metals (aluminum, brass, copper).
HOLD DOWN FOOT/BLADE GUARD The hold down foot should be lowered until it just rests on top Of the workpieoe to prevent the workpieco from lifting while cutting, but not so much that the workpiece drags. The vertical portion provides e blade guard to prevent accidental blade contact.
CLAMPING SCROLL SAW TO WORKBENCH See Figure 7. If the scroll saw is to be used in a portable application, we recommend that you fasten it permanently to a mounting board that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size to avoid tipping of saw while in use.
SQUARING TABLE TO THE BLADE See Figures 9 and 10. • Loosen the hold down foot lock knob and move hold down rod all the way up. Tighten knob. • Loosen the table lock knob and move the table untit it is approximately perpendicular, or at right angle to the blade.
HEX BOLT SAW TABLE HEX NUT ERO DEGRE STOP ASSEMBLY Fig. 11 The zero stop assembly can be rotated to the left and down out of the way and the table can be angled up to 12' to the left. See Figure 12. Note: Make sure the zero degree stop is rotated all the way down or it will contact the blade storage drawer as you angle to the left.
Loosen the foot adjusting knob. See Figure 13. To center the hold down foot around the saw blade, slide the hold down foot to the side. Tighten the foot adjusting knob. Position blade and securely tighten blade knob. Turn the quick release knob to the right or clockwise to tension the blade.
This scroll saw is designed to cut wood, wood compo- sition products, plastic, and nonferrous metals (alumi- num, brass, copper). GENERAL OPERATION Please read and understand the following items concerning your scroll saw before attempting to use the saw.
LOCK POST See Figure 17. To prevent unauthorized use of your scroll saw, we suggest that you disconnect it from the power supply and lock the knob in the OFF position. A Master Lock® 105D padlock should be used. When the lock is installed and locked, as illustrated, the switch is inoperable.
STACK CUTTING See Figure 19. After becoming well acquainted with your saw through practice and experience, you may wish to try stack cutting. Stack cutting may be used when several identical shapes need to be cut. Several pieces of wood may be stacked on top and secured to each other before cutting.
Properly support round material such as dowel rods. They have a tendency to roll during a cut, causing the blade to "bite." Toavoid this, always use a "v" block. • Clear everything except the workpiece and related support devices off the table before plugging into power and turning the saw on.
• Remove brush cap with a flat blade screwdriver. • Remove brush assembly. Gently pry the brush assembly out using a small screwdriver, point of a nail or paper clip, etc. • Check for wear. If one brush is worn down shorter than 1/4 in., replace both brushes.
21.
CRAFTSMAN SCROLL SAW- MODEL NO. 315.216360 7 40 39 FIGURE A 42 37 i i I 36 _36 16 25 19 23 24 45 46 53_ __ 52.
Po G_ Key No. 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 26 27 28 Part Number 979817-002 980119-001 979814-001 979813-001 979832-001 981385-001 979809-001 979807-001 979806-001 **S.
ro J_ CRAFTSMAN SCROLL SAW - MODEL NO. 315.216360 29 12 20 "26 24 18 14 12 14 15 37 38 39 40 42 FIGURE B I.
ro ol [ CRAFTSMAN SCROLL SAW- MODEL NO. 315.216360 I The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your SCROLL | SAW or when ordering repair parts.
In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1"800-4-MY-HOME s° (1-800-469-4663) Para pedir servicio de reparacibn a domicilio - 1-800-676-5811 Au Canada pour tout le service ou les pi_ces - 1-800-469 4663 For the repair or replacement parts you need: Call 6 a.
デバイスCraftsman 315.21636の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 315.21636をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 315.21636の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 315.21636の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 315.21636で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 315.21636を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 315.21636の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 315.21636に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 315.21636デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
