Craftsmanメーカー315.22839の使用説明書/サービス説明書
ページ先へ移動 of 66
Owner's Manual II:RRFrSMRN I 10 in. Stationary TABLE SAW Model No. 315.228390 Save this manual for future reference _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co.
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If this rRRFTSMRN Table Saw fails due to a defeat in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge.
Mounting the Leg Stand on theTable Saw Base ........................................................................................ 19 Assembling Table Extensions .......................................................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
RULES FOR SAFE OPERATION (Continued) • DO NOT OVERREACH. Keep proper footing and balance at all times. • SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and frees both hands to operate tool. • USE THE PROPER EXTENSION CORD.
RULES FOR SAFE OPERATION (Continued) • USE A SUPPORT FOR THE SIDES AND BACK OF THE SAW TABLE when sawing wide or long workpieces. Use a sturdy "outrigger" support if a table extension is more than 24 inches long and is attached to the saw, to prevent tipping.
EXTENSION CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a consid- erable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw.
Anti-Kickback Pawls Toothed safety devices behind the blade designed to stop a workpiece from being kicked back at the operator during a ripping operation, Arbor The shaft on which a blade or cutting .
Your new table saw has been designed to give you many years of high quality performance. To insure this goal, proper care and treatment is important. Careful treatment begins with removing all parts from the carton and checking them against the list of loose parts.
The following items are included with your Table Saw. D A G C I J Figure 2 a A. Table Saw Base ................................................... 1 B. Belt ....................................................................... 1 C. Belt Guard .....
Check all loose parts from the box withthelist on theprevious page, the figures below and on the following page. Small items such asfasteners andendcaps are shown in figures 2 b and 2 c. Follow the instructions in the Assembly section to assemble yournew saw.
Check all loose parts from the box with the list and figures below and on the previous pages. Small items such as fasteners and end caps are shown in figure 2 c. Follow the instructions in the Assembly section to assemble your new saw. O. Hardware for Rail, Front .
The following tools are needed for assembly and alignment. Note: The five hex keys listed below have been provided with your saw. The remaining tools are typical shop tools and are not included with your saw.
The following labels are found on your saw in the locations shown. Read all warnings and this owner's manual before using saw. B D C A A 10 inch Table Saw 3600 R.P.M. 120 VOLTS 60 Hz AC ONLY 13 A , WARNING I WHEN SERVICING, USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.
[<_ t _k WARNING When Mounting an Auxiliary Fence Face, Position Mounting Hardware Beyond Arrow at Right and Left as indicated, Keep Fasteners Away From Blade.
KNOW YOUR TABLE SAW ANTI-KICKBACK PAWLS BLADEGUARD MITER GAGE GROOVE TABLE EXTENSION RIVINGKNIFE OR SPREADER BLADE REAR RAIL ALIGN-A-CUT INSERT RIP FENCE TABLE EXTENSION SCALE MITER GAGE BELT COVER BEVEL HANDWHEEL BEVEL SCALE HEIGHT HANDWHEEL LEG STAND FRONT RAIL SWITCH WITH KEY RIP FENCE HANDLE LEVELING FOOT MOTOR BEVEL LOCK HANDLE Fig.
OVERVIEW The upper portion of the blade projects up through the table, surrounded by an insert called the throat plate, The height of the blade is setwitha handwheel on the front of the cabinet. Toaccommodate wide panels, the tabletop has extensions on each side.
Assembly is best done in the area where the saw will be used. When you remove the table saw base, loose parts, and hardware from the packing materials, check all items with the loose parts list and drawing. If you are unsure about the description of any part, refer to the drawing.
ASSEMBLING LEG STAND (Continued) • Align the two large holes on the brace and the legs. Insert the carriage bolts. Add fiat washers and hex nuts and hand tighten. Repeat for the other short upper brace. These are the front and back sets. • For the sides, install a long upper brace on two legs.
ASSEMBLING TABLE EXTENSIONS See Figure 10. • Locate the tame extensions and the sma(I hard- ware bag with the following: 8 hex bolts (5/16-18 x 1-1/4 in.' 8 hex nuts (5/16-18) 16 flat washers (5/16 in.) ,_ WARNING: The table extensions not only provide a support for large or wide pieces of material, but help protect you.
Note: The right sideof saw is on your right when facing the saw, as if you were in normal operating position. INSTALLING THE REAR RAIL See Figures 12- 14. ,4_ WARNING: Front and rear rails must be installed and carefully aligned to reduce the risk of kickback.
INSTALLING THE FRONT RAIL See Figures 15 and 16. • Get the front rail pieces, the switch assembly, and the following hardware: 6 square head bolts (5/16-18 x 1 in.
ALIGNING THE RIP FENCE AND FRONT RAIL See Figures 17 and 18. The rip fence scale indicator is installed on the right side of the rip fence but can be removed and rein- stalled on the left side if need.
INSTALLING THE BELT AND BELT GUARD See Figures 20 and 21. • Get the belt, belt guard, 4 flat washers (#10) and 4 small hex nuts (#10-24). • Lower the blade by turning the height handwheel. • Slip the belt on the saw pulley (inside cabinet). Lift the motor forward and place the belt on the motor pulley.
INSTALLING THE BLADE GUARD See Figures 23- 25. _k WARNING: If the blade is not fully lowered, turn the height handwheel to lower the blade to prevent injury • Get the blade guard, the blade guard bracket, and the following hardware: 2 hex bolts (5/16-18 x 1/2 in.
ALIGNING THE RIVING KNIFE WITH THE BLADE See Figures 26 - 28. _i WARNING: Make sure the switch is off, the switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, causing serious personal injury. The riving knife must be aligned with and centered over the blade.
CHECK HEELING (PARALLELING) OF THE SAWBLADE TO THE MITER GAGE GROOVE See Figures 29 - 30. DO NOT loosen any screws until you have checked with a square and made sure adjust- ments are necessary. Once the screws are loos- ened, these items must be reset.
CHECKING RIP FENCE AND BLADE ALIGNMENT See Figures 31 - 33. The rip fence is self-a(igning but should be checked before first use. ,_ WARNING: Failure to align the rip fence to the blade can cause jams and kickback, resulting in serious personal injury.
CHECKING SQUARENESS OF EXTENSION TABLES TO SAW TABLE See Figure 34. The extension tables should be checked for squarness to the saw table for smooth operation of the rip fence and rails. Place a square on the saw table, with the short end up and check.
To avoid unnecessary setups and adjustments, a good practice is to check your setups carefully with a framing square and make practice cuts in scrap wood before making finish cuts in good workpieces. Do not start any adjustments until you have checked with a square and made test cuts to be sure adjustments are needed.
8CRAPWOOD BLADE GUARD BLADE NUT BLADE GUARD18NOT SHOWN FORCLARITY I MARKED TOOTH AT FRONT __ FRAMING SQUARE BLADE WASHER TO TIGHTEN BLADE NUT Fig. 37 HEELING (PARALLELING) THE SAWBLADE TO THE MITER GAGE GROOVE See Figures 38- 40.
• If the blade was too close to the miter gage groove, back the bracket away with the block of wood and hammer. • Tighten the screws, raise the blade and recheck. • Repeat until blade is parallel to miter gage groove. • If the blade is not parallel, adjust the front table bracket.
• Check the 45 ° setting. Tilt the blade with the bevel handwheel as far as it will go to the left. Place the square against the blade (be sure the square is not against one of the saw teeth). If the blade is not at 45 ° , unscrew the 45 ° stop screw (right of blade), turn the handwheel until the blade is correct, and tighten the screw.
REMOVING / REPLACING THE THROAT PLATE See Figure 44. ,_k WARNING: Make sure the switch is off, the switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, resulting in serious personal injury.
BASIC OPERATION OF THE TABLE SAW A table saw can be used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, and compound cutting.
TYPES OF CUTS See Figure 46. There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the compound (bevel) miter cut. All other cuts are combinations of these basic six. Operating procedures for making each kind of cut are given later in this section.
MAKING A CROSS CUT See Figures 47 and 48. It is recommended that you make test cuts on scrap wood. Stand at the front of the saw and push the wood to the blade with the miter gage. ,_ WARNING: Make sure the blade guard is lowered over blade and is working properly to prevent possible injury.
• Place a support the same height as the top of the saw table behind the saw for the cut work. • Position the rip fence the correct distance from the blade for the cut. • For small pieces of wood, use a pushstick to move the wood into and past the blade.
• Raise the rip fence handle and remove the rip fence. • Set the blade angle by loosening the bevel lock handle and turning the bevel handwheel. Retighten the bevel lock handle. • Set miter gage to 0 ° if needed. Make sure miter gage knob is securely tightened.
MAKING A COMPOUND (BEVEL) MITER CUT See Figure 54. Practice on scrap wood. From the front of the saw, push the wood to the blade with the miter gage. Do not use the rip fence. ,_ WARNING: Make sure the blade guard is lowered over blade and is working properly to prevent possible injury.
MAKING A LARGE PANEL CUT See Figure 55. Make sure the saw is properly secured to a work surface to avoid tipping from the weight of a large panel. ,_ WARNING: Make sure the blade guard is lowered over blade and is working properly to prevent possible injury.
MAKING A DADO CUT See Figure 57. An optiona( dado throat plate is required for this procedure. See the Accessories section of this manua( and check with your nearest Sears Retail Store. A(I b(ades and dado sets must be rated at least 5,000 RPM. WARNING: Unplug the saw before working around the blade.
GENERAL MAINTENANCE ,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. ,_ WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before working on the table saw.
PROBLEM CAUSE SOLUTION Saw does not start. 1. Motor cord or wall cord is not 1. Plug in motor cord or wall cord. plugged in. 2. Circuit fuse is blown. 2. Replace circuit fuse. 3. Circuit breaker is tripped. 3. Reset circuit breaker. 4. Cord or switch is damaged.
PROBLEM CAUSE SOLUTION Fuses or circuit breakers open frequently. 1. Motor is overloaded. 2. Fuses or circuit breakers are wrong size or defective. 1. Feed work more slowly. 2. Replace fuses or circuit break- ers. 3. Dull blade. 3. Replace the blade. 4.
PROBLEM CAUSE SOLUTION Rip fence does not move smoothly. 1. Rip fence is not mounted cor- rectly. 1. Remove and reposition the rip fence. See Aligning Rip Fence and Front Rail in the Assembly section. 2. Rails are dirty or sticky. 2. Clean and wax the rails.
47 £RRFTSMRN TABLE SAW 315.228390.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 • I The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. I ] /1 11 10 J r I 4 FIGURE A rRRFTSMRN ° TABLE SAW 315.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 • I The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. I PARTS LIST FOR FIGURE A KEY PART NO.
--I r-- m _> co €,o o FIGUREB CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE I SAW or when ordering repair parts.
om P., i -4 W I-- ill 0 CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. J PARTS LIST FOR FIGURE B KEY PART NO.
-4 I:O 13"1 Or) _> co o CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE J SAW or when ordering repair parts. J PARTS LIST FOR FIGURE C KEY PART KEY PART NO.
-4 r-- rn 0o co o o'1 4_ CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE I SAW or when ordering repair parts.
-4 138 r- m co o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. J PARTS LIST FOR FIGURE D KEY PART NO.
-4 r-- I"I"1 co o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
O7 "4 P., -4 W r- rlrl o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
-4 r-- I"I"1 0o co o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
i W rrl ka co o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. J PARTS LIST FOR FIGURE F KEY PART NO.
! -4 r-- I"I"1 0o =£ co o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
Ob i -4 W r- m o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. J PARTS LIST FOR FIGURE G KEY PART NO.
-4 r-- I"I"1 0o co o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
i -4 W r- rlrl o CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. J KEY PART NO.
+ -4 Ir'-- I1"1 )i> co o Ob 4_ CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE I SAW or when ordering repair parts.
P,, i W r-" rrl o CRAFTSMAN TABLE SAW- MODEL NO. 315.228390 • I he model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. J PARTS LIST FOR FIGURE I KEY PART NO.
Para pedirservicio de reparaciCn a domicilio, Au Canada pour serviceen fran_;ais: y para ordenarpiezascon entregaa domicilio: 1-877-LE-FOYER sM 1-888-SU-HOGAR sM (1-877-533-6937) (1-888-784-6427) _ ® Registered Trademark / TM Trademark of Sears, Roebuck and Co.
デバイスCraftsman 315.22839の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 315.22839をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 315.22839の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 315.22839の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 315.22839で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 315.22839を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 315.22839の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 315.22839に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 315.22839デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
