Craftsmanメーカー320.17217の使用説明書/サービス説明書
ページ先へ移動 of 20
Operator's Manual j CRRFTSMRH°j evolv M 3/8" Keyless Drill Model No. 320.17217 000s WARNING: To reduce the risk of injury, the user must read and understand the Operator's Manual before using this product. • WARRANTY SAFETY ASSEMBLY DESCRIPTION OPERATION MAINTENANCE Sears Brands Management Corporation www.
Warranty Page 2 Safety Symbols Page 3 Safety Instructions Pages 4-7 Unpacking Pages 8 Description Pages 8-10 Operation Pages 10-13 Maintenance Page 14 Troubleshooting Page 15 Parts List Pages 16-17 Se.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
WARNING: Be sure to read and understand all instructions in this manual before using the drill. Failure to follow all instructions may result in hazardous radiation exposure, electric shock, fire, and/or serious personal injury. WARNING: Do not attempt to operate this tool until you have thoroughly read all instructions, safety rules, and warnings.
When in doubt, use the next heavier gauge. Always use UL and CSA listed extension cords. Recommended sizes of extension cords Ampere Rating More Than 0 6 10 12 Not More Than 6 10 12 16 Volts 120v Tota.
unstable and may lead to loss of control. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and more safely at the rate for which is designed. Do not use tool if the switch does not turn it on or off.
SAFETY SYMBOLS FOR YOUR TOOL The label on your tool may include the following symbols. V ............................................................... Volts A ............................................................... Amps Hz ..................
_1_ WARNING: Your drill should never be connected to the power source when you are assembling parts, making adjustments, installing or removing bits, cleaning it, or when it is not in use. Disconnecting the drill will prevent accidental starting, which could cause serious personal injury.
Fig. 2 Built-in belt chip Lock-on button Cord guard Keyless chuck Trigger switc Forward/reverse switch PRODUCT SPECIFICATIONS Motor 120V~60Hz, 5.2A No Load Speed 0-2500 (RPM) Chuck 3/8" (10ram) Cord length 6' Weight 3.
CORD GUARD Protects the cord from bending to prevent damage. BUILT-IN BELT CLiP Conveniently hooks onto your tool belt for carrying the drill. NOTE: Make sure the plug has been removed from power supply and drill bits have been removed from drill.
the forward/reverse switch while the chuck is turning. ,_k WARNING: Always disconnect your drill from the power source when replacing drill bits, tools, cleaning or when it is not in use. Disconnecting the drill will prevent accidental starting that could cause serious personal injury.
,_ WARNING: Every time you use the drill, be sure to verify the following: • Chuck jaws are tight and securing the drill bit firmly. • Drill power cord is not damaged. • Drill bit is the correct type for the material being drilled. • Drill bit is in good condition, properly installed and securely tightened.
grasp the handle and trigger switch and the other to grasp the body of the drill. NOTE: Make sure that the hand placed on the body of the drill does not cover the air vents. Covering the air vents will reduce motor cooling and possibly lead to motor overheating.
_, WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician at a Sears store or other Craftsman Evolv outlet. ,_ WARNING: For your safety, always turn off the switch and disconnect the plug from the electrical outlet before performing any maintenance or cleaning.
PROBLEM The drill does Rot start when trigger switch is squeezed Will not drill Motor overheating CAUSE SOLUTION Check to be sure power cord is connected to power source and that power source (outlet) is operable Check drill bit and chuck jaws Be sure cooling vents are free from dust and obstacles Connect to power source.
3/8" Keyless Drill MODEL NUMBER 320.17217 Always mention the Model Number when ordering parts for this tool : [: ! @ 17217 Manual Revised 09-0708 Page 16.
1 2 3 4 5 6 7 3860001000 5620179000 3550093000 5700015000 3520013000 3520016000 5700008000 Chuck Screw (L.H.) Spindle Ball Bearing Septa Gear Ball Bearing 1 1 1 1 2 1 2 8 3320036000 Le_ Housing 1 9 22.
17217 Manual Revised 09=0708 Page 18.
17217 Manual Revised 09=0708 Page 19.
Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it ! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
デバイスCraftsman 320.17217の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Craftsman 320.17217をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 320.17217の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 320.17217の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 320.17217で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 320.17217を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 320.17217の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 320.17217に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 320.17217デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。