Craftsmanメーカー486.2484の使用説明書/サービス説明書
ページ先へ移動 of 24
Owner's Manual CRI1FTSMI1N 40"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT Model No. 486.248400 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • Assembly • Operation • Maintenance • Parts : Sears, Roebuck and Co.
ACCESSORIES ................................ , .......................... 2 SAFETY RULES.._.._ ........ L..i_L_._._: .......................... 3 FULL SIZE HARDWARE CHART ......... : ....................... 4 CARTON CONTENT*S..._..,_ ...... . .:.: ...
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment, • Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly.
SHOWN ACTUAL SIZE Two shear bolts (X) and hex lock nuts (Y) are provided as replacement parts for the spiral augers. Store in a safe place until needed. (See page 17,) U IW I I NOT SHOWN ACTUAL SIZE /Z cc /GG REF. A B C - D E F G H I J K L M N O P QTY.
CARTON CONTENTS 1. Cross Brace (Weight Tray) 2. Side Brace (Weight Tray) 3. Right Hand Side Plate (Stamped "R';) 4. Left Hand Side Plate (Stamped "L") 5. Anti-rotation Bracket 6. Engagement.Rod 7. Engine Pulley Keeper 8. Chute Crank Rod Assembly 9.
TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 1/2" Wrenches (2) 9/16" Wrenches (2) 3/4" Wrenches (1) Knife ADDITIONAL ITEMS REQUIRED General Purpose Grease ASSEMBLY OF PARTS TO TRACTOR FRAME Right hand (R.H.) and left hand (L.
• Assemble a shoulder bolt to the bottom hole in each side plate, securing each bolt with a 3/8" lock washer and a 3/8" hex lock nut. See figure 3. _8" HEX LOCK NUT 3/8"LOCK WASHER R. H. SIDE PLATE 3/8"SHOULDER BOLT FIGURE3 INSTRUCTIONS FOR TRACTORS WITH FOOT REST BRACKETS UNDER THE FOOT RESTS (Figure 4.
• Assemble a shoulder bolt arid 3/8" hex lock nut to the R.H. side of the tractor fi'ame, using the first empty hole to the rear of the R.H. hanger bracket. See figure 7 Replace the engine puney keeper on your tractor with the new pulley keeper supplied with the snow blower.
Make sure the attachment clutch lever on the dash panel is in the disengaged (down) position. Position the idler arm so that it points straight forward, as shown in figure 10. Align the engage- ment rod trunnion with the hole in the idler arm by screwing the trunnion in or out on the rod.
Attach the snow thrower's clutch/idler assembly to the tractor frame by sliding the notched arms at the rear of the assembly onto the two shoulder bolts assembled to the inside of the tractor frame. Lift the front of the assembly so that the sides fit inside the R.
Insert the end of the lift release cable into the hole in the lift rod. Place the cable into the slot in the top of the lift bracket, with one hex nut above the slot and one hex nut and lock washer below the slot. Tighten the nuts, adjusting them to take out excess stack in the cable wire just above the nuts.
Coat the top of the ring around the discharge opening with general purpose grease. See figure 21. Place the discharge chute (facing forward) onto the ring. Place the anti-rotation bracket on top of the chute flange, aligning it with the holes on the right hand side of the flange.
Beneath the tractor, the idler eirm on the bottom of the clutch/idler assembly should be pivoted to the left side of the tractor as shown in figure 23. Place the auger belt around the rear pulley and between the two idler pulleys with the "V" side of the belt seated in the grooves of the "V" pulleys.
• Fill the plastic keg full of dry sand (approximately CHECKLIS'I _ 75 Ibs.) and replace the lid. Place the plastic keg on the weight tray. Secure the keg with the rubber tarp strap hooked into the holes in the cross brace.
KNOW YOUR SNOW THROWER Read this owner's manual and safety rules before operating your snow thrower. Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations. LIFT HANDLE CHUTE TILT HANDLE UPPER CHUTE LOWER CHUTE .
RAISING_AND LOWERING • To raise, push down on the lift handle until the snow thrower locks in the raised transport position. • To lower, push down slightly on the lift handle and pull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the ground.
& CAUTION: Before servicing or adjusting the snow thrower, shut off the engine, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition. REPLACING AUGER DRIVE BELT • Lower the snow thrower to the ground.
STORAGE RECOMMENDATIONS • Lower the snow thrower to the ground. • Remove the snow thrower from the tractor. • Clean the snow thrower thoroughly. Wash off any salt deposit-which may have dried on the thrower and housing. • Any bare metal that has become exposed should be painted or coated with a light oil to prevent rust.
SLOPE GUIDE (Keep this sheet in a safe place for future reference.) Use this guide to determine if a slope is safe for the operation of your tractor and snow thrower, Refer also to the instructions in your vehicle owners manual. -T . IIIIIHIIIIIIIHHiillmlllitllDlilHIl|ilillilillilUl|llll .
REPAIR PARTS FORMODEL 486.248400 40" SNOWTHROWER 16 33 / 8 3O 27.. 26 28 19 34 11 21 / 34 31 37 21 9 27 27 63 91 98 92 47 65 82 43 82 65(.) 25 21 35 30 • J 96 97 4954_ 95 "71 68 91 20.
i REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ! 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 _41 42 43 44 45 46 47 48 49 50 REPAIR PARTS FOR MODEL 486.
REPAIR PARTS FOR MODEL 486.248400 40" SNOW THROWER 42 43 41 40 45 _% 4O 63 / 69 47 51 50 53 18 52 56 / 6O 57 18 65 39 15 14 13 54 16 6 6 78 _---3 55 12 23 6 61 28 24 11 18 22 63 38 76 "&q.
REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 28 27 28 29 3O 31 32 33 34 35 36 37 38 39 4O REPAIR PARTS FOR MODEL 486.248400 40" SNOW THROWER PART NO.
For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME (1-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 In Canada for all your servic.
デバイスCraftsman 486.2484の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 486.2484をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 486.2484の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 486.2484の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 486.2484で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 486.2484を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 486.2484の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 486.2484に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 486.2484デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
