Craftsmanメーカー486.248473の使用説明書/サービス説明書
ページ先へ移動 of 24
Operator's Manual CRAFTSHAN + Model No. 486.248473 FRONT SCOOP TRACTOR ATTACHMENT DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions.
WARRANTY .................................................................... 2 SAFETY RULES .............................................................. 3 FULL SIZE HARDWARE CHART .................................... 4 CARTON CONTENTS .............
Any power equipment can cause injury if operated improperly or if the user does not understand how tooperate the equipment. Exercise caution at alltimes when using power equipment. • Read this operator's manual before attempting to assemble or operate the scoop attachment.
J J JjA J J J J J J J J J J J J J J B J J ------ J J J J J J J J J J J J J J J J J J jR T Y r-Z-1 J / / I 1 I I I I I I I I I I I I I I 1 f J J I J I I I J / / J J J J I J m G I / I I jH E}B CC j AA H.
PARTS NOT SHOWN FULL SIZE LL MM NN % PP QQ oo PARTS BAG CONTENTS Not all parts will be needed for fit-up to any one tractor. Discard unneeded parts after assembly is finished.
1. Bucket Assembly 2. Pin Stop Bracket 3. LiftFrame Assembly 4. LiftBracket Assembly 5. TiltAnchor Assembly 6. Right (Long) Side Plate 7. Left(Long) Side Plate 8. Right (Short) Side Plate 9. Left (Short) Side Plate 10. Dump Control Rod 11. LiftStrap Assembly (2) 12.
TOOLS REQUIRED FOR ASSEMBLY (1) (2) (2) (2) (2) (2) (1) Standard Screwdriver 15/16" Wrenches (one should be box-end) 3/4" Wrenches 9/16" Wrenches 1/2" Wrenches 7/16" Wrenches .
STEP 4: iNSTALL LiFT BRACKET ASSEMBLY (SEE FIGURE 3) • Assemble the lift bracket assembly to the lift frame assembly using two 5/8" washers (HH) and 1/8" x 1-1/4" cotter pins (Z).
STEP 7: iNSTALL TILT BRACKET ASSEMBLY (SEE FIGURE 6 ON NEXT PAGE) * Loosen the bolts end nuts on the tilt bracket assembly 1/4 turn or until the two plates of the assembly will slide back and forth.
STEP 10: iNSTALL TiLT STOP BRACKETS (SEE FIGURE 9) Install a tilt stop bracket (PP) to each side of the bucket using a 3/8" x 1" carriage bolt (J), 3/8" washer (EE) and 3/8" nylock nut (R).
STEP 14: iNSTALL DUMP HANDLETUBE (SEE FIGURE 13) • Install the dump handle tube to the dump pivot bracket assembly using three 5/16" x 1-3/4" hex bolts (G) and 5/16" nylock nuts (S).
STEP 17: iNSTALL HOSE CLiP AND SPACER (SEE FIGURE 16) Secure the dump cable to the back of the bucket using a hose clip (QQ), a #10 x 5/8" truss-head bolt (L) and a #10-32 nylock nut (U).
STEP 20: INSTALL FRAME BRACE (SEE FIGURE 19) * Install the frame brace to the inside of the side plates using two 1/2"x 1-3/4" bolts (B), large 1/2" washers (11), 1/2" spacers (W) and 1/2" nylock nuts (O). Install the brace in the bottom holes for Garden (GT) Tractors and the second from bottom holes for Lawn (LT) Tractors.
STEP 22: iNSTALL FRAME BRACE (SEE FIGURE 21) * Install the frame brace between the side plates using two 1/2" x 1-3/4" bolts (B), large 1/2" large washers (11), 1/2" spacers (W) and 1/2" nylock nuts (O). Fasten the brace to the second from bottom holes in the side plates.
iNSTRUCTiONS FOR ALL TRACTORS STEP 24: MOUNT SCOOPTOTRACTOR (SEE FIGURE 23) Align the scoop with the side plates on the front of the tractor. Lift the rear of the scoop and slide the notches in the scoop frame onto the bolts or pins in the tractor side plates.
STEP 26: ADJUST LiFT STRAPS (SEE FIGURE 25) * Make sure the nuts and bolts in the lift straps are loose enough to turn by hand. Stand beside the right side of the scoop and hold the lift handle as far forward as it will go until you tighten one of the nuts in the lift straps.
KNOWYOUR FRONT END SCOOP Read this owner's manual and safety rules before operating your front end scoop. Compare the illustration below with your front end scoop to familiarize yourself with the various controls and their locations.
CUSTOMER RESPONSiBiLiTiES • Read and follow the maintenance schedule and the maintenance procedures listed in this section. MAINTENANCE SCHEDULE _ _i_,_e_J_/" Fill in dates as you _o _, _/_ ;oo complete regular service.
PROBLEM Scoop won't lock into raised/transport position. Scoop bucket won't lock into level position after dumping. Lift handle trigger won't release scoop from the transport position. Dump handle trigger won't release bucket to dump.
REPAIR PARTS FOR MODEL 486.248473 79 76/ 75 /_. 77 5 4_f / 2 81 3 15 71 / 22 ./ 30 31 3: 11 64 63 29 73 _5 / 74 33 13 27 59 6q 61 / / 13 14 35 52 45 62 67 I I I 26 I / 38 39 52 41 / / / 43 42 52 45.
REPAIR PARTS FOR MODEL 486.248473 REF PART NO. QTY 1 1509-69 2 2 726-0178 6 3 49265 1 4 49266 2 5 47674 2 6 46699 1 7 47135 2 8 46053 1 9 49912 1 10 47189 3 11 47369 1 12 47368 1 13 47810 14 14 HA2136.
NOTES 22.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION OF TRACTOR WITH ATTACHMENT ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 10 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
デバイスCraftsman 486.248473の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 486.248473をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 486.248473の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 486.248473の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 486.248473で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 486.248473を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 486.248473の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 486.248473に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 486.248473デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
