Craftsmanメーカー536,884,791の使用説明書/サービス説明書
ページ先へ移動 of 19
5.0 Horsepower 22 Inch Dual Stage 120V, Electric Start SNOW THROWER MODEL NO, 536,884791 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product, SEARS, ROEBUCK AND CO.
il nP':_:) H= [o]= [o,[o]'_lld=l_',] Table of Contents 2 Service and Adjustments 14-t6 Warranty 2 Storage 17 Safety Rules 2-4 Troubleshooting 18 Contents of Shipping Carton 4-5 Repair P.
PREPARATION 1. Thoroughly inspect the area where the snow thrower is to be used and remove all doormats, sleds, boards, wires and other foreign objects. 2. Disengage all clutches before starting the engine (motor). 3. Do not operate the snow thrower without wearing adequate winter outer garments.
16. Never direct discharge at bystanders or allow anyone in front of the snow thrower. 17. Disengage power to the auger/impeller when snow thrower is transported or not in use. 18. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc).
Parts packed separately in carton (not shown full size) 2 - Ignition Keys (Attached to engine in plastic bag) 1 - Crank Assembly 1 - Snow Chute Assembly ,4k CAUTION: Always wear safety glasses or eye shields while assembling snow thrower.
• Remove and discard the packing material from around the snowthrower. • Cut all four corners of the carton from top to bottom and lay the panels flat. • Cut ties securing the clutch control cable to the lower handle and lay cable back away from the motor frame.
• Carefully remove cotter pin, clevis pin and drilled pin from yoke end of crank rod assembly (see figure below). • Place universal joint into end of worm gear lining up large holes. Insert drilled pin (ensure opening in pin is in line with small openings in universal joint) (see figure below).
Eo to] KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
Auger Drive Clutch Ignition Key insert to run pull out to stop Z_ CAUTION: Read owner's manual before operating machine. Never direct discharge toward bystanders. Release the auger control bar and stop the engine before unclogging discharge chute or auger housing and before leaving the machine.
BEFORE STARTING THE ENGINE • If the snow thrower must be moved with- out the aid of the engine, it is easier to pull the snow thrower by the handles rather than pushing. • Before you service or start the engine, fa- miliarize yourself with the snow thrower.
COLD START (See figure on this page) • Be sure the auger ddve lever is in the disengaged (Released) position, • Move the throttle control to '_ (Fast) position. • Remove the keys from the plastic bag. Insert one key into the ignition slot. Be sure it snaps into place.
• Push the primer button, see figure on page 8, while covering the vent hole as follows: (remove finger from primer but- ton between primes). One time if temperature is above 50oF. Two times if temperature is 50_F to 15°t:. Four times if temperature is below 15°F.
CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service Check Engine Oil Level Change Engine Oil Tighten All Screws & Nuts Lubricate Pivot Points Check Auger Clutch.
OIL RECOMMENDATION Only use high quality detergent oil rated with API service classification SG. Select the oil's viscosity grade according to your expected operating temperature. NOTE: For extreme cold operating condi- tions of 0 ° and below, use a partial synthetic OW30 motor oil for easier starting.
• Hold the square end of the threaded portion with pliers and adjust the Iocknut in or out until the excess slack is removed (see last figure on page 14). • Pull the cable back through the spring and connect the cable (see last figure on page 14).
mounting bolt. • Reinstall the belt cover. • Reconnect the spark plug wire. A(_dve Pulley " ,_._,,,,=_. Belt Guide ,--k -'-k" .8. Auger Idler _ Pulley Enga_ it _ _ .
Z_ CAUTION' Never store your snow thrower indoors'or in an enclosed, poorly ventilated area if gasoline remains in the tank. fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below.
TROUBLE CAUSE CORRECTION )ifficult starting Defective spark plug Replace spark plug Water or dirt in fuel system Use carburetor bowl drain to flush and refill with fresh fuel. Engine runs Blocked fuel line or low on fuel Clean fuel line; check fuel supply; erratically tank or stale gasoline add fresh fuel (gasoline/oil mix tura if 2-cycle engine).
19.
デバイスCraftsman 536,884,791の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 536,884,791をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 536,884,791の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 536,884,791の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 536,884,791で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 536,884,791を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 536,884,791の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 536,884,791に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 536,884,791デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
