Craftsmanメーカー917.271023の使用説明書/サービス説明書
ページ先へ移動 of 60
Owner's Manual CRAFTSMAN + 15.5 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTOR Model No. 917.271023 • Safety • Assembly • Operation • Maintenance • Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operating this equip- ment.
--t,_"_""_ ........... I_-""r_'•-•-_ "" .......... 2 r.•.._..._: .......... 2 • ,_...._.. ........... 5 Assemb Y.--i ...... _ ......... 8 Operati_ n... I ........ 11 Mainter mc_ ....... 18 Maintenance ..
• Tum off blades when not mowing. • Stop engine before removing grass catcher or unclogging chute. • Mow only in daylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways.
• Never make adjustments or repairs with the engine running. • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended pads, when necessary.
PRODUCT SPECIFICATIONS GASOLINE 1.25 GALLONS CAPACITY UNLEADED AND TYPE: REGULAR OIL TYPE SAE10W30 API-SF/SG/SH): (above 32°F) SAE 10W30 (below 32°F) _)IL CAPACITY: 4.0 W/PINTS 3.5 W/O I_INTS SPARK PLUG: Champion RC12YC GAP: .040 =) VALVE CLEARANCE: NOTADJUSTABLE GROUND SPEED FORWARD: 0- 5.
PARTS BAG CONTENTS SHOWN FULL SIZE (1) Large Flat Washer O (1) Hex Bolt 3/8-16 x I (1) Lockwasher 3/8 (1) Hex Bolt 5/16-18x 1-1/4 @ (1) Locknut 5/16-18 (1) Shoulder Bolt 5/16-18 (1) Washer 17/32 x 1-3.
PARTS BAG CONTENTS SHOWN FULL SIZE (2) Screws _ (2) Lock #10 x 5/8 Washers #10 (2) Weld Nuts _ O #10 (2) Washers 3/16 x 3/4 x 16 Gauge Parts packet separately in carton Seat Cassette Manual Parts Bag .
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
HOW TO SET UP YOUR TRACTOR CHECK BATTERY • Lift seat pan to raised position and open battery box door. • If this battery is put into service after month and year indicated on label (label located between terminals) charge bat- tery for minimum of one hour at 6-10 amps.
CHECK FOR PROPER POSITION OF ALL BELTS See the figures that are shown for replac- ing motion and mower blade drive belts in the Service and Adjustments sectoin of this manual. Verify that the belts are rout- ed correctly. CHECK BRAKE SYSTEM After you leam how to operate your trac- tor, check to see that the brake is properly adjusted.
These symbols may appearon your tractor or in literature supplied with the product. Learn and understand their meaning. = BAI-rERY CAUTION OR WARNING ENGINE ON ENGINE OFF REVERSE FORWARD FAST SLOW OIL.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles, or stan- dard safety ,qlasses.
• The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6 inches in height should be mowed twice.
• Unthread and remove oil fill cap/dip- stick; wipe oil off. Reinsert the dipstick into the tube and rest oil fill cap on the tube. Do not thread the cap onto the tube. Remove and read oil level. If nec- essary, add oil until UFULL" mark on dipstick is reached.
,_RGE TRANSMISSION CAUTION: Never engage or disen- gage freewheel lever while the engine is running. To ensure proper operation and perfor- mance, it is recommended that the trans- mission be purged before operating tractor for the first time.
MULCHING MOWING TIPS IMPORTANT: For best performance, keep mower housing free of built-up grass and trash.Clean after each use. • The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed.
CUSTOMER RESPONSIBILITIES AS YOU COMPLETE Check Brake Operation _ Check Tim Pm_um T Interlock Systems 14 r R Check forLoose Fasteners _ _7 _ SharpeNReplace Mower Blades _4 T Lubrication Chart 0 Check .
TRACTOR Always observe safety ruleswhen per- formingany maintenance. BRAKE OPERATION If tractorrequires morethan six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TOADJUST BRAKE" in the Serviceand Adjustments sectionof this manual).
Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and ter- minals can cause the battery to =leak" power. • Open battery box door. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.
CLEAN AIR SCREEN Air screenmust be kept free of dirt and chaffto prevent enginedamage from over- heating. Clean with a wire brush or com- pressed air to remove dirt and stubborn dried gum fibers. AIR FILTER Your engine will not run properly using a dirty air filter.
• Place new fuel filter in position in fuel line with arrow pointing towards carbu- retor. • Be sure there are no fuel line leaks and damps are properly positioned. • Immediately wipe up any spilled gaso- line. CLEANING • Clean engine, battery, seat, finish, etc.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are propedy inflated (See =PROD- UCT SPECIFICATIONS'). If tiros are over or underinflated, you will not propedy adjust your mower. SIDE-TO-SIDE ADJUSTMENT • Raise mower to its highest position.
BELT INSTALLATION - • Install new belt in reverse order of removal. Mandrel Pulley • Make sure belt is in all pulley grooves and inside all belt guides.
TO ADJUST MOTION CONTROL LEVER The motion control lever has been preset at the factory and adjustment should not be necessary. If for any reason the motion control lever will not hold its position while at a selected speed, it may be adjusted at the friction pack located on the right side of transmis- sion.
TO REMOVE CABLES, REVERSE ORDER - • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. Positive Terminal Negative Terminal Chassis Negati.
control leverfrom slowto chokeposi- tion. Slowly move leverfrom choketo fast position. • Check to see if hole in throttle lever and hole in speed control bracket are aligned. • If holes are not aligned, loosen cable clamp screw and align the holes by inserting a pencil or a 1/4" ddll bit through both holes.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _,CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM Will not start Hard to start Engine will not turn over CAUSE CORRECTION • Loose or damaged wiring. ! • Carburetor out of adjust- ment. • Engine valves out of adjustment. • Dirty air filter. • Bad spark plug. • Weak or dead battery.
TROUBLESHOOTING CHART CAUSE PROBLEM Engine clicks but will not start Loss of power Excessive vibration Engine continues to run when operator leaves seat with at tachment clutch engaged • Weak or dead battery. • Corroded battery termi- nals. • Loose or damaged wiring.
TROUBLESHOOTING CHART i PROBLEM CAUSE Poor cut - uneven • Worn, bent or loose blade. Mower blades will not rotate Poor grass dis charge Headlight(s) not working (if so equipped) Battery will not charge i • Mower deck not level. • Buildup of grass, leaves, • and trash under mower.
tROUBLESHOOTING CHART iPROBLEM CAUSE Lo_s of drive • Freewheel control in =dis- engaged" position. • Motion drive belt worn, damaged or broken.
SCHEMATIC TRACTOR - - MODEL NUMBER 917.271023 I AMMETER ;lllllE -- BATTERY SOLENOID o-r- FUSE 30 AMP. i I R CLL_CH I BRAKE _ • (PEDAL UP) ...... j ii I I LI'_=-- _ ,"....... ' : ' ' " UNE :FUEL: !---1----: , L , .......
ELECTRICAL TRACTOR - - MODEL NUMBER 917.271023 41 t i t 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.271023 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 12 Volt 28Amp 2 74760412 Bolt, HexHead 1/4-20uncx3/4 8 156417 Case, Banefy Mech Hinge 16 161343 Switch, |nt.
TRACTOR - - MODEL NUMBER 917.271023 CHASSIS AND ENCLOSURES 28 58 12 53 52 5s 54 3 3 74 3 36 14.
TRACTOR - - MODEL NUMBER 917.271023 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 11 1 160392 2 14035_ 3 17490612 4 19131216 5 155272 9 161917X013 10 STD533710 11 155927 12 145660 13 155934X010 .
TRACTOR - - MODEL NUMBER 917.271023 GROUND DRIVE 30 103 96 95 94-_ ,146 tO0 27 _lOo 55 38.
TRACTOR - - MODEL NUMBER 917.271023 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 150071B TransaxleAssembly 71 140158 Strap Torque Lh Hydro 18/20" 2 142431 Spdng, Retum.
TRACTOR - - MODEL NUMBER 917.271023 STEERING ASSEMBLY -----.__44 1 _41 27_!_27 43 44 27 2o....._ 4O.
TRACTOR- - MODEL NUMBER 917.271023 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 139768 2 154427 3 1561183 4 157473 5 62661"1 6 121748X 7 19272016 8 12000029 9 3366R 10 156438 11 STD551137 13 .
ENGINE TRACTOR - - MODEL NUMBER 917.271023 33 33 29 OPTIONAL EQUIPMENT Spark Arrester 8O 4 23 / 42.
ENGINE TRACTOR - - MODEL NUMBER 917.271023 KEY PART NO. NO. DESCRIPTION 1 162156 2 17720410 3 ...... 4 159420 13 12-041-03 14 13280328 15 13200300 16 STD551237 23 159880 29 137180 31 109202X 32 158990 33 123487X 35 17490512 37 137040 38 .
TRACTOR - - MODEL NUMBER 917.271023 SEAT ASSEMBLY I 5 KEY PART NO. NO. 1 140123 2 140551 3 STD523710 4 19131610 5 145O06 6 STD641437 7 124191X 8 17490616 9 19131614 10 155925 11 120068X 12 121246X KEY PART DESCRIPTION NO.
DECALS TRACTOR - - MODEL NUMBER 917.271023 21 7 7 6 3 1 10 16 20 11 8 12 KEY PART NO. NO, 1 156811 3 163200 4 163202 6 133644 7 163261 8 163203 9 163204 10 156439 11 142341 12 146046 KEY PART DESCRIPTION NO. NO. Decal, Oper. Instr. 14 160396 Decal, Hood, R.
TRACTOR - - MODEL NUMBER 917.271023 LIFT ASSEMBLY 5 13 12 13 3 2 6 2O 46.
TRACTOR - - MODEL NUMBER 917.271023 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 159460 Lift Lever Inner Wire Assembly 2 159471 ShaftAssembly, Lift 3 105767X Pin, Groove 4 12000002 E-Ring 5 19211621 Washer 21/32 x I x 21 Gauge 6 120183X Bearing, Nylon 7 125631X Grip, Handle, Ruted 8 122365X Button, Plunger,Red 11 139865 Link, Lilt, LH.
TRACTOR - - MODEL NUMBER 917.271023 MOWER DECK 58 17 >21 2 16 27 48.
TRACTOR - - MODEL NUMBER 917.271023 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 164961 Mower Houslog 59 141043 2 STD533107 Bolt 67 162113 3 138017 Bracket Assembly, SwayBar, 68 144200 F.
TRACTOR - - MODEL NUMBER 917.271023 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 319-O650 58 139 28 59 -91- 23 19 I 3O 9O 53 4 5 3 35 1 5O.
TRACTOR - - MODEL NUMBER 917.271023 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 319-0650 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO, DESCRIPTION 1 142930 Housing, Lower 43 142884 Washer 7/16 x 7/8 x .060 2 142931 Assembly,Upper Housing 44 150829 Dilfemn_alAseambly 3 142932 Seal, Lip 52 142991 Washer 3/4 x 1.
TRACTOR - - MODEL NUMBER 917.917.271023 KOHLER ENGINE-MODEL NUMBER CV15S, TYPE NUMBER PS-41572 AIR INTAKE J 6--1 8--W _ 11 -- _--10 _--9 CRANKSHAFT I II _ip BLOWER HOUSING AND BAFFLES I ENGINE CONTROL.
TRACTOR - - MODEL NUMBER 917.917.271023 KOHLER ENGINE-MODEL NUMBER CV15S, TYPE NUMBER PS-41572 AIR INTAKE KEY PART NO. NO. 1 12-743-05 2 25-341-02 3 12-096-24 4 12-083-08 5 12-100-01 6 X-25-63 7 12-083-05 8 12-313-04 9 12-094-12 10 12-072-05 11 12-086-01 12 12-041-02 NOT ILLUSTRATED -- 12-113-53 ENGINE CONTROLS KEY PART DESCRIPTION NO.
TRACTOR - - MODEL NUMBER 917.917.271023 KOHLER ENGINE-MODEL NUMBER CV15S, TYPE NUMBER PS-41572 FUEL SYSTEM J 4 / 7 / (_1o 14 33 CYLINDER HEAD, VALVE AND BREATHER J 25__ _4 I 15 54.
TRACTOR - - MODEL NUMBER 917.917.271023 KOHLER ENGINE-MODEL NUMBER CV15S, TYPE NUMBER PS-41572 FUEL SYSTEM KEY PART NO. NO. 1 12-853-56 2 12-041-02 3 12-053-56 4 12-041-01 5 12-089-23 6 12.079-07 7 12-265-04 8 X-426-9 9 25-353-10 10 25050-0"2 11 47-154-01 12 12.
TRACTOR - - MODEL NUMBER917.271023 KOHLER ENGINE-MODEL NUMBER CV15S, TYPE NUMBER PS-41572 IGNITION I ELECTRICAL I mit 14-- ,_D e-----:r OIL PAN I LUBRICATION I CRANKCASE I 10 2 STARTING SYSTEM J 3- i .
TRACTOR -- MODEL NUMBER 917.271023 KOHLER ENGINE-MODEL NUMBER CV15S, TYPE NUMBER PS-41572 IGNITION I ELECTRICAL CRANKCASE KEY PART KEY PART NO. NO. DESCRIPTION NO.
58.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL (.n co 6 Operate your Tractor up and down the face of slopes (not I I greater than 15°), never across the face. Make turns gradu- r ally to prevent tipping or loss of control.
For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar plezas con entrega a domicilio - 1-800-659-708.
デバイスCraftsman 917.271023の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman 917.271023をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 917.271023の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 917.271023の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 917.271023で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 917.271023を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 917.271023の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 917.271023に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 917.271023デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
