Craftsmanメーカー917270841の使用説明書/サービス説明書
ページ先へ移動 of 60
Owner's Manual 16.0 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRAOTO Model No. 917.270841 Safety Assembly Operation o Maintenance o Repair Parts CAUTBON: Read and follow all Safety Rules and Instructions before operating this equip- ment.
Warranty ......................................................... 2 Safety Rules .................................................. 2 Product Specifications ............................ 5 Assembly ................................................ 6 Operation .
o Turn off blades when not mowing° o Stop engine before removing grass catcher or unclogging chute. o Mow only in daylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. o Watch for traffic when operating near or crossing roadways.
o Never make adjustments or repairs with the engine running° Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary_ ° Mower blades are sharp and can cut.
PRODUCT SPECiFiCATiONS GASOLINE 1.25 GALLONS CAPACITY AND TYPE: UNLEADED REGULAR OIL TYPE API-SF/SGiSH): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) OIL CAPACITY: 30 PINTS SPARK PLUG: Champion RC12YC GAP: .030") GROUND SPEED FORWARD: 0- 5.7 (MPH): REVERSE: 0- 2.
(1) Large Fiat Washer (1) Hex Bolt 3/8-16 x 1 (1) Lockwasher 3/8 (1) Hex Bolt 5/16-18× 1-1/4 (1) Locknut 5/16-18 (1) Shoulder Bolt 5/16-18 (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Knob (2) Hex Bo!ts .
PARTS BAG CONTENTS SHOWN FULL SiZE (2) Screws _ (2) Lock #10 x 5/8 L_._ Washers #10 (2) Weld Nuts #10 (2) Washers 3/16 x 3/4 x 16 Gauge Parts packet separately in carton Seat Video Cassette St_rmgWhe_.
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
HOW TO SET UP YOUR TRACTOR CONNECT BATTERY ,_kCAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, re- move metal bracelets, wristwatch bands, rings, etc.
CHECK BRAKE SYSTEM After you learn how to operate your trac- tor, check to see that the brake is propedy adjusted. See =TO ADJUST BRAKE" in the Service and Adjustments section of this manual. iNSTALL MULCHER PLATE o Install two latch hooks to rnulcher plate using screw, washer, lock washer, and weld nut as shown.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. E3 BATTERY ENGtNE ON FUEL CAUTION OR REVERSE WARNING @ ENGINE OFF OIL PRESSURE .
KNOW YOUR TRACTOR READ THBS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various control.
repairs,, We recommend a wide vision safety mask over the spectacles, or standard safety glasses. HOW TO USE YOUR TRACTOR Your tractor is equipped with an operator presence sensing switch,, When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine,.
hot months. For healthier and better looking lawns, mow often and after moderate growth. o For best cutting performance, grass over 6 inches in height should be mowed twice.
o For cold weather operation you should change oil for easier starting (See "OIL VISCOSITY CHART" in the Mainte- nance section of this manual)° - To change engine oil, see the Mainte- nance section in this manual. ADD GASOLINE • Fill fuel tank_ Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane.
PURGE TRANSMISSION ,_CAUTION: Never engage or' disen- gage freewheel lever while the engine is running. To ensure proper operation and perfor- mance, it is recommended that the trans- mission be purged before operating tractor for the first time.
MULCHING MOWING TaPS IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean after each use° ,, The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed.
CUSTOMER RESPONSgBgUTIES Check Brake Operation _ Check Tire Pressure _ _#' ..... Check Operator Presence and T L.I ntedOck Systems .............. R Check for LoOse Fasteners _ _ - 6/'7 ............. 6 _' (A S.,_Roplsce Mowor Blades :] .
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
. Rinse the battery with plain water and dry. o Clean terminals and battery cable ends with wire brush until bright. o Coat terminals with grease or petroleum jelly. o Reinstall battery (See "CONNECT BAT- TERY" in the Assembly section of this manual).
AIR FILTER Your engine will not run properlyusinga dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions.
CLEANING o Clean engine, battery, seat, finish, etc. of all foreign matter_ o Keep finished surfaces and wheels free of all gasoline, oil, etc. o Protect painted surfaces with automo- tive type wax.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway° Make sure tires are properly inflated (See =PROD- UCT SPECIFICATIONS").
o Work belt off both mandrel pulleys and idler pulleys. = Pull belt away from mower: BELT INSTALLATION = Install new belt in reverse order of removal° Mandrel Pulley • Make sure belt is in all pulley grooves and inside all belt guides° ° Install mower in reverse order of removal instructions° Idler Pulleys Mandrel Pulley TO ADJUST BRAKE ,.
TO ADJUST MOTION CONTROL LEVER The motion control lever has been preset at the factory and adjustment should not be necessary° tf for any reason the motion control lever will not hold its position while at a selected speed, it may be adjusted at the friction pack located on the right side of transmis _ sion_ o Park tractor on level surface.
TO ATTACH JUMPER CABLES - • Connect each end of the RED cable to the POSITIVE (+) terminal of each bat- tery, taking care not to short against chassis. o Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery. ° Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.
TO REMOVE HOOD AND GRILL AS- SEMBLY o Raise hood. o Unsnap headlight wire connector. o Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor° = To replace, revers.
ACCELERATION TEST- o Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (counter- clockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine accelerates smoothly= High speed stop is factory adjusted.
TROUBLESHOOTING CHART PROBLEM CAUSE Engine clicks but o wilt not start o (conrd) _J u..., Loss of power CORRECTION Loose or damaged wiring. Faulty solenoid or starter° • Cutting too much grass/too fast. • Throttle in "CHOKE" posi- tion.
TROUBLESHOOTING CHART CAUSE =ROBLEM Poor cut - uneven (cont'd) Mower blades will not rotate , ,: ,,,,,,.,, Poor grass dis- charge Headlight(s) not working (if so equipped) , ,,i,,,,,,,,, Battery .
31.
32.
SCHEMATIC TRACTOR - - MODEL NUMBER 917.270641 !tl ° "°° o11io BA'T'rERY ___)G L( ]iGNITION SWITCH I -_, (PEDAL UP} U'x.D FUSE B0 AMP ',-0,,(3-+---- _ ....... J CLUTCH t BRAKE (OPTIONAL) , _JEL, _ ' "A LINE ' | ! FUEL SHUT, OFF SOLENOID I O['-,KNGE [ .
ELECTRICAL TRACTOR- - MODEL NUMBER 917.270641 +++++ 22 --, 33 19 2 25 2B 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.270641 KEY PART NO. NO. 1 144925 2 74760412 3 STD551025 4 STD551125 6 STD541025 8 156417 16 153664 19 STD551125 20 73350400 21 147430 22 4152J 24 4799J 25 14614.
TRACTOR - - MODEL NUMBER 917.270641 CHASSIS AND ENCLOSURES 37 53 3 3 74 28 12 55 57 54 13 . 14 36.
TRACTOR - - MODEL NUMBER 917.270641 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION t 160392 Chassis Assembiy 2 t40356 Drawbar 3 17490612 Screw, Thd Roll 3/8-16 x 3/4 4 19131216 Washer 13/32 x3/4 .
TRACTOR -- MODEL HUMBER 917.270641 GROUND DRIVE 57 51 88 19 98 30 35 62 36 32 61 84 100 105 37 27 72 70 I16 --66 ..._50 ,,-148 _lso _ ,,. 150 151 _ ,,.
TRACTOR - - MODEL NUMBER 917=270641 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 140607 Transmission, Asm, 69 142432 2 142431 Spring, Rebam, Brake 70 134683 3 144698 Pulley, Transmissi.
TRACTOR -- MODEL HUMBER 917.270541 STEERING ASSEUBLY _42 G2 .... ,, '_ 20 1tT .._ / ._ _ .7" 47 jt k 10 67 43 40.
TRACTOR -- MODEL NUMBER 917.270641 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION I 139768 Steedng Wheel 2 154427 Axle Assembly STMP Dropped STL 3 156483 Spindle Assembly, LH, 4 !57473 Spindle Assembly, R H,.
ENGINE TRACTOR - - MODEL NUMBER 917o270641 33 3 81 / 78 38 7 13 4 29 OPTIONAL EQUIPMENT Spark Arrester 23 / 42.
ENGINE TRACTOR - - MODEL NUMBER 9't7.270641 KEY PART NO. NO. DESCRIPTION 1 162157 2 17720410 3 ........ 4 137352 13 272293 14 13280324 15 13200300 t6 STD551237 23 t59880 29 137180 31 109202X 32 158990 33 123487X 35 17490512 37 137040 38 .
TRACTOR- - MODEL NUMBER 917.270641 SEAT ASSEMBLY 5 . 21 KEY NO. I 2 3 4 5 6 7 8 9 10 11 PART NO. 140122 140551 STD523710 19131610 145006 STD541437 124181X 17490616 19131614 155925 12OO68X KEY PART DESCRIPTION NO.
DECALS TRACTOR -- MODEL NUMBER 917.270641 13 10 13 6 3 4 8 14 KEY NO. PART NO. 1 156811 3 163200 4 I63202 6 133644 8 163203 9 163204 10 156439 12 146046 13 163252 14 160396 KEY PART DESCRIPTION NO. NO. DESCRIPTION Decal, Opor. Instr 15 273832 Decal, Hood, RH 16 142341 Decal, Hood, LH.
TRACTOR - - MODEL NUMBER 917.270641 LIFT ASSEMBLY 11 13 i € i 32 13 19 20 15 46.
TRACTOR -- MODEL NUMBER 917.270541 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION i 159460 Washer Asm Inner Spring WtPIunger 2 159471 ShaflAsm. Uft 3 I05767X Pin Groove 4 12000002 E Ring #5133-62 5 19211621 Washer21/32 x I x21 Ga.
TRACTOR - - MODEL NUMBER 917.270641 MOWER DECK 17 34 33 32 103 105 16 18 18 29 27 48.
TRACTOR - - MODEL NUMBER 917.270641 MOWER DECK KEY PART KEY PART NO, NO. DESCRIPTION NO. NO. 1 144393 Mower Housing 51 STD541410 2 STD533107 Bolt 52 139888 3 138017 Bracket Assembty, Sway Bar, 53 1318.
TRACTOR -- MODEL NUMBER 917.270641 HYDRO TRANSAXLE - - MODEL NUMBER 310-0500 5O.
TRACTOR - - MODEL NUMBF-.R 917.270641 HYDRO TRANSAXLE-- MODEL NUMBER 310-0500 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. ! 142986 Housing, Lower 40 150778 2 142987 Assembly, Upper Housing 41 142958.
TRACTOR-- MODEL NUMBER 917.270_1 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 L 230 _614 635 337 23O 1_ REQUIRES SPECIAL TOOLS TO INSTALL SEE REPAIR iNSTRUCTION MANUAL 294 166.
TRACTOR -- MODEL NUMBER 917.270641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 127 138 106 987 °,11, T 105 51 142 121 CARBURETOR OVERHAUL KIT 52 164 _123 "A" REQUI.
TRACTOR - - MODEL HUMBER 917.270641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE HUMBER 1174-E1 _ 523 423 _524 3 20 634A 842 524 868 868A 358 GASKET SET 977 CARBURE-I'OR GASKET s_-r 171.
TRACTOR -- MODEL HUMBER 917.270641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 209 728 265 201 482 I to_9 LA.Et. K,T 1 !_o_ LABEL KiT' EMissioNsJ 240 615 783 801 803 503.
TRACTOR - - MODEL NUMBER 917.270641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E1 KEY PART NO. NO. 1 496412 2 399265 3 391086 4 494238 5 495858 7 273280 8 495735 9 27803 10 946.
TRACTOR - - MODEL NUMBER 917.270641 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1t74-E1 KEY PART NO. NO. 294 810068 304 496280 305 94786 308 225020 307 94930 309 497595 310 497602 31.
58.
SUGGESTED GUIDE FOR SiGHTiNG SLOPES FOR SAFE OPERATION I "" SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. It A Operate your Tractor up and down the face of slopes (not _] _ greater than 15°), never across the face.
For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1 =800-366=PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-70.
デバイスCraftsman 917270841の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Craftsman 917270841をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman 917270841の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman 917270841の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman 917270841で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman 917270841を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman 917270841の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman 917270841に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman 917270841デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。