CraftsmanメーカーEZ3 917.259172の使用説明書/サービス説明書
ページ先へ移動 of 60
® 917.259172 OWNER'S MANUAL ° Assembly o Operation o Customer Responsibilities o Service and Adjustments o Repair Parts For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm, Mon - Sat CAUTION: Read and follow all safety rules and instructions before operating this equipment.
ii/_ iil ¸ . SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE lS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS= FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
CONGRATULATIONS on your purchase of a Sears Tractor° It has been designed, engineered and manufac- tured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Authorized Service Center/Department Department.
TABLE OF CONTENTS SAFETY RULES ............................................................ 2 PRODUCT SPECIFICATIONS ...................................... 3 CUSTOr_IER RESPONSIBILITIES ..................... 3, 17-19 WARRANTY .........................
ACCESGORIEG AN ATTACHMENTS These accessories and attachments were available through most Sears retail outlets and service centers when the tractor was purchased. Most Sears stores can order these items for you when you provide the model number of your tractor.
CONTENTS OF HAF DWA E PACK Parts Bag contents shown full size (1) Hex Bolt 3/8-16 x I (1) Large Flat Washer '1) Hex Bolt 5/!6-18 x 1-1/4 _J (1) Lockwasher 3/8 (1) Locknut 5116-18 (t) Shoulder (1) Hex Bolt Bolt 5/16-18 1/2-13 x I (1) Lock Washer 1/2 _(2) Lock _ Washers _ ) (2) Washers _.
ASS LY Your new tractor has been assembled at the factor,] with exception of those parts left unassembled for shipping purposes, To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
............................................. i TL o Connect BLACK grounding cable to negative (-) bat- tery terminal with remaining hex bolt, flat washer, lock washer and hex nuL Tighten securely. ° Close terminal access doors. Use terminal access doors for: ° Inspection for secure connections (to tighten hard- ware).
INSTALL iVlULCHER PLATE (See Figs. 5 & 6) • Install two latch hooks to mulcher plate using screw, washer, lock washer, and weld nut as shown. NOTE: Preoassemble weld nut to latch by hook inserting weld nut from the top with hook pointing dow n.
OPERATION These symbols may appear on your tractor or in titerature supptied with the product. Learn and understand their meaning_ BATTERY CAUTION OR REVERSE FORWARD FAST WARNING ENGINE ON ENGINE OFF .
OPERATmON KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of vario.
OPERATmON HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 8) Your tractor is equipped with an operator presence sensing switch, When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine_ = Depress clutch/brake pedal into full "BRAKE" position and holdo .
OPERATgON CAUTION: Do not operate the mower R without either the entire grass catcher, on mowers so equipped, or the dis- charg e guard in place. _ ! NOTE: To protect hood from damage when transportin.
OPERATION TO START ENGINE (See Fig. 7) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position.
OPERATION NIOWING TIPS MULCHRNG IVIOWING TIPS o Tire chains cannot be used when the mower housing is attached to tractor. Mower should be properIy leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual,.
CUSTO PeNS L TIES scHEod& AS You COMPL E REGULARSERVICE __ERVIOE DATES Check Brake Operation ......... _--_ ................... - ...................... : ...... _ ............. ........ Check Tire Pressure _ 6#'* T Check for Loose Fasteners I_ # .
OUSTOME RESPON ILITIES TRACTOR Always observe safety rules when performing any mainte- nance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.. (See 'q'O ADJUST BRAKE" in the Service and Adjust- ments section of this manual),.
¢USTO ESPONS LnTmES V-BELTS Check V-belts for deterioration and wear'after t 00 hours of operation and replace if necessary_ The belts are not adjustable.. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling.
OUSTO ER ESPONS BILmES IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KEROSENE, ARE NOT TO BE USED TO CLEAN THE CARTRIDGE THEY MAY CAUSE DETERIORATION OF THE CARTRIDGE DO NOT OILCARTR1DGE.
,i,,i,,11111 , ,, i, i, ,i ,,i, ,,_ SERVICE AN ..................... ............... ii " :": AOJUSTMENT$ ................... i ............ ii .... i CAUTION: O O o @ o o BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: Depress clutch/brake pedal fully and set parking brake, Place motion control lever in neutral (N) position.
$£RV C£ AN ADJUSTMENTS TO LEVEL MOWER HOUSING FRONT-TO-BACK ADJUSTMENT (See Figs° X3 and X4) Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT SPECIFICATIONS" on page 3 of this manual).
SERVHCE A ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 25) The mower blade drive belt may be replaced without tools, Park the tractor on level surface° Engage parking brake.
SERVBCE AN ADJUSTMENTS L ,,, ,, .... ,,,,,,, , .......... TO ADJUST MOTION CONTROL LEVER (See Fig. 28) The motion control lever has been preset at the factory and adjustment should not be necessary° .
SERVICE AND ADJUSTMENTS TO START ENGINE WITH A WEAK BATTERY See Fig. 30) CAUTION: Lead-acid batteries gener- ate explosive gases. Keep sparks,flame and smoking materials away from bat- teries, Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged.
SERVnCE AND ADJUSTMENTS ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32) The throttle control has been preset at the factory and adjustment should not be necessary, Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows: o With engine not running, move throttle control lever to fast position.
ERV CE AND ADJUSTMENTS TO ADJUST CARBURETOR (See Figs. 34 & 35) The carburetor has been preset at the factory and adjust- rnent should not be necessary. However, minor adjust- rnent may be required to compensate for differences in fuel, temperature, altitude or load.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.
TROU LESHOOTING POre TS PROBLEM Will not start Hard to start IL !l ' ! III J IJI_LIIJlJ: : Engine will not turn over Engine clidks but will not start Loss of power Excessive vibration CAUSE 1, Out of fuel, 2, Engine not "CHOKED" properly.
TROV LESHOO G POUNT$ PROBLEM Engine continues to run when operator leaves sea with attachment clutch engaged Poor cut - uneven Mower blades will not rotate CAUSE t. Faulty operator_safety presence control system t. Worn, bent or loose blade. 2_ Mower deck not level.
3O.
SCHEMATIC TRACTOR -- MODEL NUMBER 917.259172 RED BATTERY BLACK AMMETER (OPTIONAL) S B IGNITION SWITCH RED WHITE FUSE 30 AMR ! ! | t 'O;O' ! 1 c_+-- J CLUTCH / BRAKE (PEDAL UP) IGNITION SWITCH POSITION CIRCUIT "MAKE" OFF G + M + L NONE RUN/LIGHT B + L .
REPAIR PARTS TRACTOR - - MODEL NUMBER 917=259172 ELECTRICAL T ! t I I I I I i i 52._ ) f 29 I i ! I ! , l 70 ,1 ,_, I | I I I I i I I i t I t i I I i I ! t I I I t I 1 I I / * I I I I // / / / ! / .
REPAIR PARTS TRACTOR -- MODEL NUMBER 917.259172 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 2 74760412 3 STD551025 4 STD551125 6 STD541025 8 7603J 10 145211 11 150109 12 145769 16 153664 19 STD55.
REPAnR PARTS TRACTOR -- MODEL NUMBER 917.259172 CHASSIS AND ENCLOSURES 29 28 58 12 t4 11_._ 3 37 6O 3 / 3 74 38_ 39 34 14 37 37 i 53 20 45 23 52 55 57 54.
REPAIR PARTS TRACTOR - - MODEL NUMBER 9'17.259172 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 160392 2 140356 3 17490612 4 STD551025 5 155272 9 161917X011 10 STD533710 11 155927 12 1456.
REPAnR PARTS TRACTOR -- MODEL NUMBER 917,259172 DRIVE 51 37 116 48 48 150 151 51 53 36.
REPAPR DRIVE PARTS TRACTOR - - MODEL NUMBER 917,259172 KEY NOo 1 2 3 8 10 16 t8 19 21 22 24 25 26 27 28 29 3O 32 34 35 36 37 38 39 40 41 42 47 48 49 50 51 52 53 55 56 57 59 61 62 63 64 PART NO.
REPA!IR PARTS TRACTOR - - MODEL NUMBER 917.259172 STEERING ASSEMBLY . tl 62 25 ' 68 1 t¸ 2o._,J z" "29.- ._ o -I 47 65 38.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 139768 2 154427 3 156483 4 157473 5 6266H 6 121748X 7 192720'16 8 12000029 9 3366R 10 156438 !1 S.
REPAaR PARTS TRACTOR -- MODEL NUMBER 917.259172 ENGINE 31 39 15 14 81 32 { 40 37 27 7 17 29 OPTIONAL EQUIPMENT Spark Arrester 23 / e 4 40.
REPAIR ENGINE PARTS TRACTOR -- MODEL NUMBER 917,259172 KEY PART NO. NO. DESCRIPTION 1 2 3 162152 17720410 4 149723 5 144O69 6 144068 7 138129 8 150176 10 145552 11 STD551125 12 STD522507 13 272250 14 .
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 SEAT ASSEMBLY 14 KEY NO. 1 2 3 4 5 6 7 8 9 10 12 13 PART NO. 140123 140551 STD523710 19131610 145006 STD541437 124181X 17490616 19131614 155925 121246X 121248X KEY PART DESCRIPTION NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 DECALS 6 7 74 2 10 14 22 19 13 14 15 KEY NO. PART NO. 1 156439 2 156810 3 160284 4 160285 5 273503 6 133644 7 150927 9 146709 10 150333 11 156811 13 146046 KEY DESCRIPTION NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 MOWER LIFT 11 49 12 6 8 / 1 / / / /' / / /..../1 5 19 13 32 13 --_y" t t i 32 13 19 20 15 20 161718 15 20 44.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 MOWER LIFT KEY PART NO, NO. DESCRIPTION 1 159460 Wire Assy. Inner, Spring w/Plngr Lt 2 159471 Shaft Asmo Lift 3 105767X Pin Groove 4 12000002 E Ring #5133-62 5 192t 1621 Washer 21/32 x 1 x 21 Ga.
REPAhR PARTS TRACTOR - - MODEL NUMBER 917,259172 MOWER DECK 52 58 68 34 33 32 102 17 ''-104 105" .,_ 106 105 106 2 16 18 21 22 23 24 25 26 27 46.
REPAnR PARTS TRACTOR-- MODEL NUMBER 917.259172 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 144393 2 STD533107 3 138017 4 138440 5 STD624008 6 130832 8 850857 9 STD551137 10 .
REPAIR PARTS TRACTOR -- MODEL NUMBER 917.259172 HYDRO GEAR TRANSAXLE - MODEL NUMBER 310-0650 58 18 27 28 59 91 19 23 26 44 ÷ ./' 17 14 63 ÷ 4 5 3 11 11 -36 35 48.
REPAIR PARTS TRACTOR -- MODEL NUMBER 917,259172 HYDRO GEAR TRANSAXLE - MODEL NUMBER 310-0650 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 142930 Housing, Lower 43 t42884 Washer 7/16 x 7/8 x ,.060 2 142931 Assembly, Upper Housing 44 150829 Differential Assembly 3 142932 Seal, Lip 52 142991 Washer 3/4 x 1.
REPABR PARTS TRACTOR - - MODEL NUMBER 917.259172 BRIGGS & STRATTON ENGINE - MODEL NUMBER 42E707, TYPE NUMBER 2631-E1 615 ':_ 24 634A ÷ N SS2A ® 615 q_ 552 220 _ _ 2ao _ 32 868 _i) _ 40 35 3.
REPAIR PARTS TRACTOR-- MODEL NUMBER 917.259172 BRIGGS & STRATTON ENGINE - MODEL NUMBER 42E707, TYPE NUMBER 2631-E1 1358 GASKET SET,, I 1861 PUMP REPAIR KIT] ! 121 CARBURETOR KIT I 98 _ ,,_.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 BRIGGS & STRATTON ENGINE - MODEL NUMBER 42E707, TYPE NUMBER 2631-E1 653 783 801 /_ 802 544 803 311 ill l , i,ii ii ill i,ii .
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.259172 BRIGGS & STRATTON ENGINE - MODEL NUMBER 42E707, TYPE NUMBER 2631-E1 8A 9 10A 304 572 10 305 5A 13 1 Io.
REPA6R PARTS TRACTOR - - MODEL NUMBER 917.259172 BRIGGS & STRATTON ENGINE - MODEL NUMBER 42E707, TYPE NUMBER 2631-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917,259172 BRIGGS & STRATTON ENGINE - MODEL NUMBER 42E707, TYPE NUMBER 2631-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO.
SERVICE NOTES 56.
$ERVRCE NOTES 57.
SERVICE NOTES 58.
0 I:Z: LLI 0 LU U. ,,< U) 0 I,l., 00 LLI 0 .,,,J I !-. U) 0 I.,I. LU a I :3 Q LU I- t_ W :3 U) / /- / / ,.J i :Z: Z 0 Q ,,,,j Z_I ,,'8 o:O >.
OWNER'S MANUAL MODEL NO. 917.259172 IF YOU NEED REPAIR SERVICE OR PARTS: FOR REPAIR SERVICE, CALL THIS TOLL FREE NUMBER: 1-800-4-REPAIR (1-800-473-7247) FOR REPLACEMENT PARTS INFORMATION AND ORDERING, CALL THIS TOLL FREE NUMBER: 1-800-FON-PART (1-800-366-7278) FOR CONSUMER ASSISTANCE HOT LINE, CALL THIS TOLL FREE NUMBER: 1-800-659-5917 ® 19.
デバイスCraftsman EZ3 917.259172の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman EZ3 917.259172をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman EZ3 917.259172の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman EZ3 917.259172の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman EZ3 917.259172で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman EZ3 917.259172を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman EZ3 917.259172の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman EZ3 917.259172に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman EZ3 917.259172デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
