CraftsmanメーカーLAWN TRACTOR 917.272051の使用説明書/サービス説明書
ページ先へ移動 of 60
Owner's Manual ICRAFTSMAN°J 16HP ELECTRIC START 42" MOWER 6 SPEED TRANSAXLE LAWN TRACTOR Model No. 917.272051 • Safety • Assembly • Operation • Maintenance • Repair Parts This product has a low emission engine which operates differently from previously built engines.
Warranty ............................................... 2 Safety Hules ......................................... 3 Product Specifications .......................... 6 Assembly .............................................. 8 Operation ...............
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting.
hi. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and under the watchful care of another responsible adult.
• Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops white going uphill, disengage blades, shift into reverse and back down slowly.
PRODUCT SPECIFICATIONS GASOLINE 1.25 GALLONS CAPACITY UNLEADED _,ND TYPE: REGULAR OILTYPE SAE 10W30 (ABOVE 32°F) API-SF-SJ): SAE 5W-30 (BELOW 32°F) :)IL CAPACITY: W/FILTER: 4.0 PINTS W/OFILTER: 3.5 PINTS ;PARK PLUG: CHAMPION RC12YC 3AP: .040") _ROUND SPEED FORWARD: 'vlPH): 1 sT 1.
Steering Wheel Insert (1) Hex Bolt 3/8-16 x 1 Steering Boot _," Steering Wheel (1) Lock washer 3/8 (1) Large Flat Washer {1) Hex Belt 5/16-18 x 1-1/4 (1) Locknut 5/t6-18 _ Steering Wheel Adapter .
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
Label Battery Door Terminal INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2, Pivot seat upward and remove from the cardboard packing.
INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of mulcher plate over front of mower deck opening end slide into place, as shown. 3. Hook front latch into hole on front of mower deck.
These symbols may appear on your tractor or in literature supplied with the product, Learn and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OIL P.
KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor te familiarize yourself with the Iocatiens ef various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
• The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6 inches in height should be mowed twice.
TOWING CARTS AND OTHER ATTACHMENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing, Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.
COLD WEATHER STARTING ( 50 + F and below) 6. When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position.
MAINTENANCE SCHEDULE 1. ChBP, gl _re oltert wh#n oporat _ i_r _ I-_avy _d _ _ I_g_ am_ le_m_ur_ 5. If equlppiKI w_h ad_t _*b_B _y_ 2. S._icl _m Oft_ _ opomhng in d.dy or du_t_ coPd_ion5 6. _ req_ro_ 1_ _,_ w_h m_dnl_,_e.fr ,*,m ba_o_. 3. If equipped w_thoH filter, char, go _1 _ 50 ho,Jr_ 7.
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high sp.eed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
• Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers.
Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary.
CLEANING Clean en_]ine, battery, seat, finish, etc. i of all foreign matter. Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automo- tive type wax.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are propedy inflated (See "PROD- UCT SPECIFICATIONS" section of this manual), if tires are over or underinflated, you will not properly adjust your mower.
TO REPLACE MOWER BLADE DRIVE BELT • The mower blade drive belt may be rel_laced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL- 1. Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).
TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (look gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1.
Positive Terminal Negative Terminal Keps_ Hex Nut :, Bolt Battery Positive Terminal Negative Terminal REPLACING BATTERY _CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-read engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION; Never store the tractor ' with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Will not start Hard to start Enginewill not turn over Engine clicks but will not start 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter.
TROUBLESHOOTING CHART PROBLEM CAUSE Less of power 1. Excessive vibration Enginecontinues to run when operator leaves seat with with attachment clutch engaged Poorcut-uneven Cutting too much grass/too fast. 2. Throttle in "CHOKE" position. 3.
PROBLEM Mower blades will not rotate TROUBLESHOOTING CHART CAUSE 1. Obstruction in clutch mechanism. 2. WorWdamaged mower drive belt. 3. Frozen idler pulley. 4. Frozen blade mandrel. Poor grass discharge Headlight(s) not working (if so equipped) 1. Engine speed too slow.
SCHEMATIC TRACTOR -- MODEL NUMBER 917.272051 BAT'_'ERY SO',-ENX){O o2o--- _o,:T :o_--_ j I _ED i FUSE _ _ , STARTER CLUTCH / BRAKE J (PEDAL UP) i i _rtE i i ' i eLUE i _ i B UE I .
ELECTRICAL TRACTOR - - MODEL NUMBER 917.272051 25 32.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.272051 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt Hex Hd 1/4-2Ounc x 3/4 8 156417 Case Battery 16 161343 Switch, Intedock 21 166182 Harness A.
TRACTOR - - MODEL NUMBER 917.272051 CHASSIS AND ENCLOSURES 12 60 207 207 57 74 2011 84.
TRACTOR -- MODEL NUMBER 917.272051 CHASSIS AND ENCLOSURES KEY PART NO. NO, DESCRIPTION 1 174619 ChasSis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X013 Dash 10 STD533710 Bolt, Carriage 3/3-16xl 11 155927 Panel, Dash, LH.
TRACTOR - - MODEL NUMBER 917.272051 GROUND DRIVE 24 36.
TRACTOR - - MODEL NUMBER 917.272051 GROUND DRIVE KEY PART NO. NO. DESCRIPTION KEY PART NO. NO, DESCRIPTION 1 ........ Trarlsaxle (See Breakdown) 63 175410 Pulley, Engine Peedess 206-545C 64 71170764 B.
TRACTOR - - MODEL NUMBER 917.272051 STEERING ASSEMBLY 38.
TRACTOR - - MODEL NUMBER 917.272051 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 139768 SteedngWheel 2 154427 Axle Assemriy STMP Dropped STL 3 169840 Spindle Assembly, LH.
ENGINE TRACTOR-- MODEL NUMBER 917.272051 OPTIONAL EQUIPMENT Spark Arrester 23 1 4 KEY PART NO. NO. 1 170548 2 17720410 3 ...... 4 174667 13 12-041"03 14 148456 16 STD551237 23 169837 29 137180 31 1092(_X 32 1589£0 33 123487)( KEY PART DESCRIPTION NO.
TRACTOR - - MODEL NUMBER 917.272051 SEAT ASSEMBLY KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 140123 Seat 13 121248X Bushing Snap BIk Nyi 50 Id 2 140551 Bracket Pnt Pivot Seat (blk) 14.
DECALS TRACTOR -- MODEL NUMBER 917.272051 11 13 10 12 2O 14 KEY PART NO. NO. 1 156368 2 171762 3 171698 4 171699 5 138047 6 133644 7 177368 8 172331 9 163204 10 156439 KEY PART DESCRIPTION NO. NO. DESCRIPTION Decal, Oper. Instr. 11 177325 Decal, Hood Side Decal, Replacement 12 146046 Decal, V-Belt Ddve Schematic Decal, Hood, R.
TRACTOR - - MODEL NUMBER 917.272051 LIFT ASSEMBLY 19 13 32 19 13 KEY PART NO. NO. 1 159460 2 159471 3 105767X 4 12000Q32 5 19211621 6 120183X 7 125631X 8 122365X 11 139865 12 139866 DESCRIPTION Washer Asm Inner Spring W/ Plunger Shaft Asm. Lilt Pin Groove E Ring #5133-62 Washer 21/32 x 1 x21 Ga.
TRACTOR - - MODEL NUMBER 917.272051 MOWER DECK 17 _21 >21 106 _ 102 103 105 ,o,d/<;-" ,'jl J> ,o+<_. - j,j+, l + 01 _+_,.+,+,_1 106 102 / • .
TRACTOR - - MODEL NUMBER 917.272951 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 165892 Mower Deck Assembly, 42" 67 149846 2 STD533107 Doff 68 144959 3 138017 Bracket As.
TRACTOR -- MODEL NUMBER 917.272051 PEERLESS TRANSAXLE -- MODEL NUMBER 206-545C O -- 71B 18 4 47 180_ 150 so 29 35 157 NUMBERS HERE 46.
TRACTOR - - MODEL NUMBER 917.272051 PEERLESS TRANSAXLE -- MODEL NUMBER 206-545C P_= PART _ PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 772147 Transaxle Cover 41A 7g0079 2 789(_5A Needle Beadng 5/8" 42 792073A 3 770128 Transaxle Case 42A 792085A 4 776395 Countershaft .
TRACTOR - - MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 CYLINDER HEAD, VALVE AND BREATHER I 1 "1o 2O t9 t8 19 1 / @ 'IB _---L 48.
TRACTOR - - MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 CYLINDER HEAD/VALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO.
TRACTOR -- MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 IGNITION/ELECTRICAL I AIR INTAKE J 3-- BLOWER HOUSING AND BAFFLES l 12 I0 _--5 4 S 50.
TRACTOR -- MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 IGNITION/ELECTRICAL BLOWER HOUSING & BAFFLES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 12-086-14-6 Screw, hex. flange M1Ox1.5x46 2 12-468-03-S Washer, plain 3/8" 3 24-162-03-S Screen, grass 4 25-086-47-S Bolt, shoulder M6xl.
TRACTOR - - MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 STARTING SYSTEM 1 I i 8 8 ! 6 ENGINE CONTROLS 1 11 :_IL PAN / LUBRICATION J 2 4 _ lm -e I _5 8- 7 11 20 52.
TRACTOR - - MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 STARTING SYSTEM ENGINE CONTROLS KEY PART KEY pART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 M-839070-S Screw, hex. flange 1 MEx1.25x70 (2) 2 2 25-098-07-S Starter assembly (Includes 3 3-8) 4 3 12-755-54-S K_, drive end 4 12-227-t8-S Cap, drive end 5 5 12.
TRACTOR - = MODEL NU MBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 CRANKSHAFT 1 2_ EXHAUST J 3 FUELSYSTEM I 54.
TRACTOR - - MODEL NUMBER 917.272051 KOHLER ENGINE-MODEL NUMBER CV461, TYPE NUMBER 26504 FUEL SYSTEM CRANKSHAFt" KEY PART NO, NO. DESCRIPTION 1 M-641060-S 2 X-22-11-S 3 M-629116-S 4 12-853-68-S 5 12-041-02-S 6 12-053-68 Nut, hex. flange M6xl.0 (2) Washer, lock 1/4" Stud M6x1.
56.
57.
58.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL _ Operate your Tractor up and down the face of slopes (not I i greater than 15°), never across the face. Make turns gradu- [ a ally to prevent tipping or loss of control.
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM Anytime, day or night (1-800469-4663) www.
デバイスCraftsman LAWN TRACTOR 917.272051の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Craftsman LAWN TRACTOR 917.272051をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCraftsman LAWN TRACTOR 917.272051の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Craftsman LAWN TRACTOR 917.272051の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Craftsman LAWN TRACTOR 917.272051で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Craftsman LAWN TRACTOR 917.272051を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCraftsman LAWN TRACTOR 917.272051の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Craftsman LAWN TRACTOR 917.272051に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCraftsman LAWN TRACTOR 917.272051デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
