Cub Cadetメーカー48-inch, 54-inch, 60-inch, 72-inchの使用説明書/サービス説明書
ページ先へ移動 of 32
Hydr ostatic Zer o-T urn Commer cial Riding Mo wer Professional Turf Equipment OPERATOR’S AND SERVICE MANUAL 48” Fabricated Deck 54” Fabricated Deck 60” Fabricated Deck 72” Fabricated Deck.
2 T ABLE OF CONTENTS F oreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Saf ety Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 FOR W ARD The T ank Hydrostatic Zero-T ur n Commercial Riding Mower pro vides superb maneuv erability , mid-mount cutting capability f or profession al landscapers, commercial la wn ser vice compa - nies, prof essional turf managers and golf course superintendents.
4 GENERAL SAFETY OPERA TIONS A. D ANGER 1. Do not operate mach ine in confined areas where e xhaust gases can accumulate. 2. Do not oper ate machine without mo wer chute deflector in place and operationa l. 3. Do not carry passengers. B. W ARNING 1. Do not oper ate machines under the influence of alco hol or dru gs.
5 11. When looking for oil leak s , n e ver run your hand o ver h ydraulic hoses , lines or fittings . Ne ver tighten or ad just hydra ulic hoses, lines or fitti ngs while the sy stem is under pressure.
6 blade bolts are tight before restarting the engine. 13. Ne ver leav e the mow er unattended without: turning off the blade clutch s witch; placing the left and r ight steer ing le vers in the neutra.
7 SAFETY DECALS AND LABELS K E E P HA ND S a n d F E E T AW AY DA NG E R TO R E DU CE THE RI S K O F I N J U RY , DO NO T OP E R A T E M O W E R UN L E S S DI S CHARG E CHUT E CO V ER O R GRAS S C ATCH ER I S I N I TS PRO PER PL A CE. WARNING SHIELD MISSING DO NOT OPERATE Do not put hands or feet under or into mower when engine is running.
8 SPECIFICA TIONS GENERAL INFO . Contr ols: Engine ignition and star t switch; th rottle; chok e; left and r ight steering lev ers; electric blade clutch s witch; parking brake; mow er deck lift P arking Brake: Mechanical linkage brak e handle to inter nal dr um brak es Seat: Adjustab le seat and ar mrests .
9 OPERA TING INSTR UCTIONS A.General 1. When Mowing: a. K eep adults , children, and pets aw ay fr om the area to be m o wed. b . Wh en operating this mower , in the forward direction, do not allo w the steer ing le vers to retur n to Neutral on th eir own.
10 b . Av oid tur ning do wnhill if possible, if not use e xtra care and go slo wly . c. A void turning when going downhi ll, traction is at a minimum going do wnhill. d. Do not oper ate with discharge side of the mow er towa rd streets, b uildings, p lay - grounds , parking lots, othe r machines, ani - mals, an d other people.
11 4. Electric Blade Clutch Switc h: (See Figure 1.) Located on the right side of the mo wer beside the ignition s witch. This is an “on/off ” push pull s witch that controls the electric bl ade clutch which supplies power to the cut - ting bl ades through the PT O.
12 C.Initial Adjustments 1. Check the flu id levels and tires: Note: These checks should be made daily , befo re star ting the engine. a. Fuel: Using a good grade of unleaded, regular gasoline (f or a gasoline engine), fill the fuel tank (beside t he engine on the left or ri ght side of the mower).
13 f . Raise t he mowing deck to the transpor t position usin g the transpor t lev er . g. Use the transp or t lev er to lower the mow - ing dec k to the cutting position and repeat step “b . ” abov e to mak e sure that the desired cutting height has been attained .
14 3. Mov e both lap bars out of the neu tral/ star t position to th e neutral position (tow ard center of machine). Slo wly , mov e both lap bars to ward the front of the machine until the machin e begins to mov e f orward — release the lap ba rs and the machine should sto p.
15 Note: Do not hold the key in the “Start” position for more than 10 seconds o r y ou may damage the star ter . If th e engine do es not start in this time, wait abou t 30 seconds and try again. i. Gasoline Engine: Once the engine s tar ts, push the ch ok e on halfwa y and as the engine warms, push the chok e off all the way .
16 MAINTENANCE AND SER VICE W ARNING: Disconnect the spark pl ug wires or r emo ve the key fr om the ignition to prevent the engine from accidentally starting before performing any maintenance on th is mower . A. Mower Dec k 1. Removing the Mo wer Deck: a.
17 a. Set the parking brak e. b . Clean any debris fr om the blades. K eep bl ades shar p and free of b uild up at all times. c. Sharpen bl ades ev enly at the original 30° angle to maintain balanced cut ting blades . Do not sharpen the underside of the bl ades.
18 1. Adding Hydraulic Oil (use Rimu la SAE15W40) a. Place the Mower on a le v el surface and engage the pa rking brake. b. Stop the engine and remo ve the key fro m the ignition switch. c. Clean the area around the Hydr aulic Oil fill neck. d. Remove the h ydraulic fill cap and check the le vel.
19 c. Store the batter y with a full charge . A dis - charged batter y will fr eeze (ref er to the table belo w). d. Recharge battery when e v er the specific gra vity value is less than 1.225 3. Battery Remov al Wa r n i n g : When removing the cables from the batter y follo w these steps to avoid a short between the wrench and the frame.
20 adjustment specs. There are three in spec - tion slots in the brake co ver . T o adjust, suc - cessiv ely tig hten each of the three gap adjustment nu ts an equal amount. Inser t a f eeler gage (see p age 22 f or specs) into each slot as th e air gap adjustment nut are tightened.
21 a. Balance inflation pressure bet ween the rear tires t o help maintain straight trav el (see tire side w all for prop er inflation pres - sure). b . K eep the valv e caps tightened to pre vent air pressure loss. 2. Leaking T ires: When a flat tire occurs , repair or replace immed iately .
22 T o adjust either brak e individually , disconnect the brake rod from the brake ar m by removing the cotter pin from the cle vis pin and pulling the cle v is pin from the brak e clevis . Loosen the he x nut and turn the brak e clevis in a cloc kwise direction one full turn looking do wn the brak e rod.
23 opened out to the neutr al position. If the Mow er begins to creep, adjust the Steering Le vers. If the mow er creeps, first deter mine whether it creeps to the right or left side and which direc - tion the mow er mov es — to the front or the rear .
24 MAINTENANCE SCHEDULE A. Daily Chec ks 1. Before star ting engine: a. Check th e fuel lev el.** b . Check the engine oil le vel.** c. Check the h ydraulic oil lev el. d. Check the h ydraulic hoses f or leaks, abra - sion, kink s , tw ists, or a flattened condit ion.
25 . OIL CHAR T Apply a f ew drops of en gine oil or use a spra y lubricant. Apply the oil to both sides of pivot points . Wipe off any e xcess. Star t engine and operate mo wer briefly to insure that oil spreads ev enly .
26 P erformance Adjustments A. High Speed T racking Adjustment If mow er tracks to one side wi th both lap bars in fully f orward position: 1. Chec k air pressure in all four tires: a. Pressure should be within specif ied ranges and balanc ed side-to-side.
27 g. V er ify proper th rottle adjustment b y check - ing RPM readings as outlined abo ve . C. Deck Corner Ball Wheel Roller Settings 1. Matching the set heights of the ball rollers on the f our cor ners of the mo wer deck to the desired cut height will pre vent edg e scalping and minimize an y side-to-side variance in cut height.
28 F . Deck le veling Procedure 1. P ar k the mower on a flat pav ed surface , engage the park ing brak e, shut off the engine, remove the ke y from the i gnition s witch, discon nect the spark plu g wires and using the transpor t lev er , low er the mowing deck into the 4" height of cut position.
29 WIRING DIA GRAM GD: 02000591.
30 MAINTENANCE RECORD DA TE WORK PERFORMED DA TE WORK PERFORMED.
31.
MANUF A CTURER’S LIMITED W A RRANTY - TURF EQUIPMENT This warr anty is specific t o the produc t manual to wh ich it is attac hed. For a complete list of pr oducts and warranties con t act y our authorized Cub Cadet Commer cial dealer . Proper maintenance of the pur chased Cub Cadet Commer cial equipment is the owner’ s responsibility .
デバイスCub Cadet 48-inch, 54-inch, 60-inch, 72-inchの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cub Cadet 48-inch, 54-inch, 60-inch, 72-inchをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCub Cadet 48-inch, 54-inch, 60-inch, 72-inchの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cub Cadet 48-inch, 54-inch, 60-inch, 72-inchの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cub Cadet 48-inch, 54-inch, 60-inch, 72-inchで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cub Cadet 48-inch, 54-inch, 60-inch, 72-inchを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCub Cadet 48-inch, 54-inch, 60-inch, 72-inchの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cub Cadet 48-inch, 54-inch, 60-inch, 72-inchに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCub Cadet 48-inch, 54-inch, 60-inch, 72-inchデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。