D-LinkメーカーGO-DSL-N150の使用説明書/サービス説明書
ページ先へ移動 of 70
.
i Contents 1 Introduction ........................................................................................................ 1 1.1 Safety Precautions ................................................................................ 1 1.2 LEDs and Interfaces .
GO-DSL-N150 User Manual ii 3.7.4 SysRestart ................................................................................ 52 3.7.5 Diagnostics ............................................................................... 53 3.8 Help .............
GO-DSL-N150 User Manual 1 1 Introduction The GO-DSL-N150 device is an ADSL acce ss device that supports multiple line modes. With four 10/100Base-T Ethernet inte rfaces at the user e nd, it provides high-speed ADSL broadband connection to the Internet or Intranet for high-end users such as net cafes and office user s.
GO-DSL-N150 User Manual 1.2 LEDs and Interfaces Front Panel The following table describes the LEDs of the device. LEDs Color Status Description On The device is powered on or the initiation of the device is successful. Green Off The device is powered off.
GO-DSL-N150 User Manual LEDs Color Status Description Off The LAN connection of the device is failed. On The device has successful WLAN connection. Blinks Data is being transmitted on WLAN. WLAN Green Off The WLAN connection is failed. Off WPS is disabled.
GO-DSL-N150 User Manual 4 1.3 System Requirement s Recommended system requirements are as follows: A 10/100 base-T Ethernet card is installed on your PC A hub or Switch.
GO-DSL-N150 User Manual 2 Hardware Installation Step 1 Connect the DSL interface of the device and the Modem interface of the splitter through a telephone cable. Connect the phone to the Phone interface of the splitter thr ough a cable. Connect the incoming line to the Line interface of the splitter.
GO-DSL-N150 User Manual Figure 1 Connect io n dia gra m ( W ithout connecting tel ephone sets before the splitter) Connection 2 Figure 2 shows the connection when the splitter is installed close to the router .
GO-DSL-N150 User Manual Note: When con ne cti on 2 is us ed , th e fil t er mus t be ins talled c los e to the t e lepho n e cable. See F igure2. Do no t use the splitter to rep lace the filter .
GO-DSL-N150 User Manual 3 About the Web Configuration This chapter describes how to configur e the ro uter by using the Web-based configuration utility . 3.1 Access the Router The following is the detailed description of accessing the router for the first time.
GO-DSL-N150 User Manual 3.2.1 Device Info Choose Status > Device Info . The page that is displayed shows the current status and some basic settings of the rout er , such as Firmware V ersion, LAN, W A N, ADSL and other information. 3.2.2 System Log Choose Stat us > System Log , the page shown in the following figure appea rs.
GO-DSL-N150 User Manual 3.2.3 Statistics Choose Status > St atistics . The Statistics page that is displayed contains Ethernet S tatistics, AD S L St atistics and WLAN S tatistics. 3.2.3.1 Ethernet St atistics In the T raffic S tatistic page, click Ethernet and the page shown in the following figure appears.
GO-DSL-N150 User Manual 3.2.3.2 ADSL St atistics In the T raffic S tatistic page, click ADS L and the page shown in the following figure appears. In this page, you can view the ADSL line statistics such as total PDUs and total Error Counts.
GO-DSL-N150 User Manual When subscribing to a broadband service, you should be aware of the method by which you are connected to the Internet. Y our physical WAN device can be either PPP , ADSL or both. T echnical information about your Internet connection properties is provided by your Internet se rvice provider (ISP).
GO-DSL-N150 User Manual Click NEXT , the page as shown in the following figure appears. Click EXIT, this page will be closed. In this page, enter a new password for t he admin a ccount. After finishing all quick start settings, it will be saved and effect immediately.
GO-DSL-N150 User Manual There are five WAN connection ty pes: Auto setup by ISP list, Dynamic IP Address, St atic IP Address, PPPoE/PPPoA and Bridge Mode . Select the appropriate wan connection type which is provided by your ISP . For example, select the PPPoE/PPPoA, and then click NEXT , the page as shown in the following figure appears.
GO-DSL-N150 User Manual After setting, click NEXT , the page as shown in the following figure appears. Click BA CK to modify the settings. Click NEXT to save the settings.
GO-DSL-N150 User Manual 16.
GO-DSL-N150 User Manual 17 The following table describes the parameters of this page: Field Description Virtual Circuit You can select a virtual circuit from the drop-list. Click PVCs Summary you can view eight PVCs (from PVC0 to PVC7), and only PVC0 status is activated by default.
GO-DSL-N150 User Manual If your ISP provides you an IP address automatically , you may select Dynam ic IP in the ISP encapsulation. Dynamic IP is typically used for Cable se r vices.
GO-DSL-N150 User Manual 19 Field Description access to the Internet fails. Normally NA T is enabled. Default Route Y ou can enable or disable the default route. If enable this function, the current PVC will be the default gateway to internet from this device.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Encapsulation Y ou can choose 1483 Bridge d IP LLC , 1483 Bridged IP VC-Mux , 1483 Routed IP LLC(IPoA) or 1483 Rout ed IP VC- Mux . Default Route Y ou can enable or disable default route.
GO-DSL-N150 User Manual 21 Field Description which is provided by your ISP. Gateway Y ou can enter the gate way ip for dial-up , which is provided by your ISP. NA T Select it to enable Network Address T ranslation (NA T) function. If you do not select it but want to access the Internet normally , you mu st add a route on the uplink equipment.
GO-DSL-N150 User Manual 22.
GO-DSL-N150 User Manual 23 The following table describes the parameters of this page: Field Description Username Enter the username for PPPoE dial-up, which is provided by your ISP. Password Enter the password for PPPoE dial-up, which is provided by your ISP.
GO-DSL-N150 User Manual 3.4.2 LAN Choose Interfac e Setup > LAN . The LAN page that is displayed contains Router Local IP , DHCP Server and DNS . In this page, you can change IP address of the router . The default IP address is 192.168.1.1, which is the private IP address of the router .
GO-DSL-N150 User Manual 25 Field Description Dynamic Route Y ou can select RIP1 or RIP2 . Direction Y ou can select None , Both , IN Only or OUT Onl y . Multicast IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group.
GO-DSL-N150 User Manual also act as a surrogate DHCP server (DHCP proxy) where it relays IP address assignment from an actual DHCP server to client s. Y ou can enable or disable DHCP server or DHCP proxy . In the DHCP field, choose Disabled , the page shown in the following figure appears.
GO-DSL-N150 User Manual 3.4.3 Wirele ss Choose Interface Setup > Wirel ess . The page as shown in the following figure appears. The Wireless page contains Access Point Settings , 1 1n Settings , Multiple SSIDs Settings , WPS Settings and Wireless MAC Address Filter .
GO-DSL-N150 User Manual 28 The following table describes the parameters of this page: Field Description Access Point Y ou may choose Ac t iva te d or Deactivated . Channel Countries apply their own regulations to both the allowable channels, allowed users and maximum power levels within these frequency ranges.
GO-DSL-N150 User Manual 29 Field Description client can not search the SSID. Use WPS WPS technology allows new customers without a previously-established account to securely connect to your network at the Wi-Fi hotspot, create and pay for an account, and access the Internet.
GO-DSL-N150 User Manual 3.5.1 Firew all Choose Adv a nc e d S e tu p > Firew all . The page shown in the follow ing figure appears. Y ou can select this option to automatica lly detect and block Denial of Service (DoS) attacks such as Ping of Death, SYN Flood, Port Scan and Land Attack.
GO-DSL-N150 User Manual The following table describes the parameters and buttons of this page: Field Description Destination IP Address Enter the IP address of the destination device.
GO-DSL-N150 User Manual The following table describes the parameters and buttons of this page: Field Description Virtual Circuit Choose a Virtual Circuit Index to set up for the NA T function. NA T S tatus This field shows the current NA T status for the current VC.
GO-DSL-N150 User Manual Field Description DMZ Select Enable to enable this function. DMZ Host IP host on the Address Enter the specified IP Address for DMZ LAN side. the NA T p age, select the number of IPs as Single and choose Vir tua l Se r ver , he LAN), for example, Web In and the p age shown in the following figure appears.
GO-DSL-N150 User Manual 34 Field Description Rule Index The Virtual server rul Y ou can le IP e index for this VC. specify 10 rules in maximum. All the VCs with sing will use the same Virtual Ser ver rules. Application Select an application type for this VC.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Rule Index The Virtual server rule index for this VC. Y ou can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Ser ver rules.
GO-DSL-N150 User Manual 3.5.4 QoS Choose Adva nc e d Se tu p > QoS , the page shown in the follo wing figure appears. This option provides better service of selected network traffic over various technologies. The QoS can be set based on the physical LAN ports or wireless interfaces.
GO-DSL-N150 User Manual 37 Field Description QoS, you may set the upload bandwidth of the WAN interface. Rule Index Y ou may establish at most sixteen QoS rules. Active Y ou may select Act i vat ed or Deacti vated . The QoS rule can be set if it is activated.
GO-DSL-N150 User Manual Field Description Range T ype of Service Support services including Normal service , Minimize delay , Maximize throug hput , Maximize reliability and Minimize monetary cost . DSCP Range DSCP Range is from 0 to 63 . 802.1p Select this option to Activate/Deactivated the 802.
GO-DSL-N150 User Manual 3.5.5 VLAN Choose Adva n ce d Se tu p > VLAN , the page shown in the following figure appears. Virtual LAN (VLAN) is a group of devices on one or more L ANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segment s.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description PVID Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description VLAN Index Define the VLAN Group ID (1 to 8). Active Choose to active or deactive the VLAN group. VLAN ID Input a VLAN ID for the Group. AT M V C s Select what A TM VCs (0 to 7) will join the VLAN group.
GO-DSL-N150 User Manual 3.5.6 ADSL Click Ad va n c e d S e t u p > AD S L , the page shown in the following figure appears. The ADSL featu re can be selected when you meet the physical connection problem. Please check the proper settings wi th your Internet service provider .
GO-DSL-N150 User Manual The following table describes the parameters and buttons of this page: Field Description ACL Rule Index Y ou can establish sixteen ACL rules at most. Active Click to enable or disable the rule. Secure IP Address The rule is valid if the IP is in this r ange.
GO-DSL-N150 User Manual UDP or ICMP) and a specific direction (inc oming, outgoing, or bot h) to filter the packet s . The following table describes the parameters and buttons of this page: 44 Field Description Filter T ype Selection Support IP / MAC Filter , Application Filter and URL Filter .
GO-DSL-N150 User Manual Field Description Rule T ype Support IP or MA C . Source IP Address Enter the Source IP Address. 0.0.0.0 means don't care. Port Number Enter the Port Number . 0 means don't care. Destination IP Address Enter the Destination IP Address.
GO-DSL-N150 User Manual The following table describes the parameters and buttons of this page: Field Description Application Filter Choose to activate or deactiva te the Application Filter rule. ICQ Set All o w or Deny ICQ packets. MSN Set All o w or Deny MSN packet s.
GO-DSL-N150 User Manual The following table describes the parameters and buttons of this page: Field Description Active Make URL Filter rule activated or deactivated. URL Inde x Can set an URL Filter Index from 1 to 16. URL Enter the URL that needs to be filtered.
GO-DSL-N150 User Manual UPnP device can dy namically join a net work, obtain an IP address, convey it s capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Dynamic DNS Choose to activate or deactivate DDNS function.
GO-DSL-N150 User Manual he following table describes the parameters of this page: T Field Description New Password Enter the password ant to change the to which you w old password.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Synchronize time with Y ou can choose NTP Server automatically , PC’s Clock or Manually . T ime Zone Choose the time zone in which area you are from the drop-down list.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description New Firmware Location Click Browse to select the firmware file. New Configuration Location Click Browse to select the configuration file. Configuration Backup Click it, and select the p ath.
GO-DSL-N150 User Manual The following table describes the parameters of this page: Field Description Current Settings Save the current settings and then reboot the router. Factory Default Settings Reset to the factory default settings and then reboot the router .
GO-DSL-N150 User Manual 3.8 Help In the navigation bar , click Help . The Help page that is displayed contains Quick Start , Inter face Setup , Ad v a nc e d S et u p , Access Management , Mainte nance and Status . Y ou can get information on detailed functions and parameter configuration of the device.
GO-DSL-N150 User Manual 55 (Unspecified Bit Rate). These QoS types are all controlled b y the parameters specified below , including PCR, SCR and MBS. PCR : Peak Cell Rate. SCR : Sustained Cell Rate. MBS : Maximum Burst Size. Internet :: Encapsulation Dynami c IP : Select this option if your ISP provides you an IP address automatically .
GO-DSL-N150 User Manual 56 Connection Setting : Fo r PPPoE/PPPoA connection, you can select Al w ays on or Connect on-demand . Connect on d emand is dependent on the t raffic. If there is no traffic (or Idle ) for a pre-specified period of time), the connection will tear down automatically .
GO-DSL-N150 User Manual 57 Internet :: MAC S poofing MA C Sp oof ing (Internet MAC S poofing) is XXXX. LAN settings These are the IP settings of the LAN inte rface for the device. These settings may be referred to as Private settings. Y ou may change the LAN IP address if needed.
GO-DSL-N150 User Manual 58 DHCP Server IP for relay agent : The DHCP server IP Address runs on W AN side. LAN :: DNS Server The DNS Configuration allows the user to set the configuration of DNS DNS Relay selection If user want to disable this feature, he just need to set both Primary and secondary DNS IP to 0.
GO-DSL-N150 User Manual 59 Wi-Fi Protected Access, pre-shared ke y . En crypts data frames before transmitting over the wireless network. Pre-shared Key : The Pre-shared Key are used to encrypt data. Both the ADSL Router and the wireless clients must use the same WP A-PSK key for data transmission.
GO-DSL-N150 User Manual 3.8.3 Adv anced Setup Choose Help > Advanced Setup , the page shown in the following figure appears. This page that is displayed contains Firewall , Routing , NA T , QoS and ADS L .
GO-DSL-N150 User Manual 61 NA T Select this option to setup the NA T (N etwork Address T ranslation) function for your ADSL router . Virtual Circuit : Enter Virtual Circuit Index that you plan to setup for the NA T function NA T St atus : Thi s field shows the current status of the NA T function for the current VC.
GO-DSL-N150 User Manual 62 NA T :: IP Address Mapping The IP Address Mapping is for those VCs that with multiple IPs. The IP Address Mapping rule is per-VC based. (only for Multiple IPs' VCs). Rule Index : The Virtual server rule index for this VC.
GO-DSL-N150 User Manual 63 differentiated Internet services by giving network resource and usage control to the Network operator . QoS::Applications QoS Select this option to Activated/Deacti vated the different application packets prioritized on the queues.
GO-DSL-N150 User Manual devices attached are configured to transmit untagged frames. Many NICs for PCs and printers are not 802.1Q-compliant. If the y receive a tagged frame, they will not understand the VLAN tag and will drop the frame. Also, the maximum legal Ethernet frame size for tagged frames was increased in 802.
GO-DSL-N150 User Manual IP Filter Select T elnet, FTP , TFTP , Web, SNMP , Ping to block incoming W AN requests for the corresponding service(s). SNMP Simple Network Management Protocol is used for exchanging information between network devices. Get Communit y : Select to set the p assword for the incoming Get requests from the management station.
GO-DSL-N150 User Manual Admini stration There is only one account that can access Web-Management interface. It is admin. Admin has read/write access privilege. In this web page, you can set new password for admin. Time Zone The system time is the time used by the device for scheduling services.
GO-DSL-N150 User Manual 67 System Log The ADSL Router keep s a running log of events and activities occurring on the Router . If the device is rebooted, the logs are automatically cleared. St atistics The ADSL R outer keeps statistic of traffic that p asses through it.
デバイスD-Link GO-DSL-N150の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
D-Link GO-DSL-N150をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはD-Link GO-DSL-N150の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。D-Link GO-DSL-N150の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。D-Link GO-DSL-N150で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
D-Link GO-DSL-N150を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はD-Link GO-DSL-N150の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、D-Link GO-DSL-N150に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちD-Link GO-DSL-N150デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
