DCM SpeakersメーカーDCM-2の使用説明書/サービス説明書
ページ先へ移動 of 36
1 DCM Series *TD-000106-00* TD-000106-00 Rev .B Digital Cinema Monitor & Crossover System USER MANUAL DCM-1 DCM-2 DCM-3.
2 © Copyright 2002, QSC Audio Products, Inc. QSC® is a registered trademark of QSC Audio Products, Inc. “QSC” and the QSC logo are registered with the U.
3 The DCM hardware unit and DCM Manager software are the property of QSC Audio Inc. Information in this document is subject to change without notice and does not represent a commitment on the part of QSC Audio. The software described here is furnished under a licensing agreement.
4 Thank you and congratulations on your purchase of the QSC DCM Digital Cinema Monitor . This product represents the state-of-the-art for cinema-based signal processing and monitoring functions in a single, integrated system.
5 The DCM is highly durable and carefully packaged. We recommend you inspect the unit carefully after removing it from the packaging, as occasionally there may be damage due to some unfortunate incident during shipment. Report any damage to the shipping carrier .
6 System Design Features The DCM series Digital Cinema Monitor has many unique features which combine to make this the most cost effective and versatile systems solution in the industry . Installer Features: •Provides Monitor and Crossover functions in one box.
7 6. Password Security : The crossover settings that you create can make a dramatic difference in the sound quality within the theater . Many installers pride themselves on being able to adjust the electrical parameters (crossover points, equalization, delay , etc) to exactly compliment the speaker and room interactions.
8 ILLUSTRA TIONS- DCM-1 1- Power switch 2- Monitor output speaker 3- Processor/Amps selector switch 4- Monitor source selector switches 5- Monitor volume control 6- Diagnostics check switch 7- Power .
9 ILLUSTRA TIONS- DCM-2 1- Power switch 2- Monitor output speaker 3- Processor/Amps selector switch 4- Monitor source selector switches 5- Monitor volume control 6- Diagnostics check switch 7- Power .
10 ILLUSTRA TIONS- DCM-3 1- Power switch 2- Monitor output speaker 3- Amplifier/Processor selector switch 4- Monitor source selector switches 5- Monitor volume control 6- Diagnostics check switch 7- P.
11 HARDW ARE DESCRIPTION- Front Panel FRONT PANEL The front panel of the DCM series resembles traditional cinema monitor products. This provides the projec- tionist a well known and easy to understand interface. The Emergency Bypass switch setting alters the Power Status of the Center Channel amplifier .
12 Monitor Source Selection Switches: Pressing any of the Monitor Select buttons will either select or deselect the corresponding (marked) signal for monitoring. Each button can select either the Proces- sor signals (input to the DCM) or the Amplifier signals (output to the speakers), depending on the current selection of the PROC/AMP switch.
13 Diagnostics Check Button and Indicators: The Diagnostics / Indicator section includes an ex- tremely simple method of verifying proper system operation and performing basic troubleshooting.
14 HARDWARE DESCRIPTION- Front Panel Emergency Bypass: This is an extremely powerful feature. If there should ever be a problem with the DCM or system cabling, you have the ability to bypass all of the DCM active circuitry and get sound to the center channel.
15 Amplifier DataPorts: One QSC amplifier DataPort includes all connections required to send two channels of audio from the DCM to the amplifier input circuitry , and current and voltage information back from the two speaker terminal outputs.
16 From Processor Output: This connection is from the cinema processor , and is the input source of all film sound into the DCM unit. The 25-pin connector is an industry standard type and pinout, and will connect into your system very easily . These cables are available from several cinema supply houses.
17 HARDW ARE DESCRIPTION- Rear Panel T erminal Strip Connections : The terminal strip in- cludes convenient connections for output to a powered subwoofer , a Hearing Impaired audio output, and on the DCM-2 and 3, a remote control on/off logic connection ( EX MODE ) for the surround decoder system.
18 T o access the powerful crossover and system calibration functions of the DCM hardware, you must use the DCM Manager control software. A 9-pin male to female serial data cable is also needed to connect your PC to the DCM.
19 INST ALLA TION- Rack Mounting RACK MOUNTING Rack mounting of the DCM is optional. Four , self-adhesive rubber feet are included with your DCM for non- rack mount applications.
20 INST ALLA TION- Rear Rack Ears (optional accessory) For mobile and touring use, it is extremely important to support the rear of the DCM. The chassis and rack can be damaged if the DCM is not properly supported. Unless the DCM is being installed in its final, fixed location, QSC strongly recommends supporting the rear of the unit.
21 1- IEC-style AC power cord (included with the DCM) 2- QSC DataPort cable for every amplifier (8, 11, or 15 cables depending upon model) 3- Cinema Processor cable (DB25 male-male) 4- RS-232 cable (D.
22 The RS-232 port is used only for setup and system troubleshooting. Connect the 9-pin serial data cable from the host PC to this connector on the DCM. Orient the male DB9 connector to match up with the RS-232 port, push the connector into the receptacle to seat it, and finger -tighten the retaining screws.
23 The QSC DataPort connection carries input signals, amplifier output monitoring signals, remote amplifier power on/standby control, amplifier temperature, and more, all on one cable. Each DataPort is clearly marked indicating which channel’ s amplifier it should be connected to.
24 Audio signals are input to the DCM via the FROM PROCESSOR OUTPUT connection. This DB25-type connection conforms to cinema industry standard pinout. Most common cinema processors use this DB25 connec- tion standard, making connection to the DCM simple.
25 The Hearing Impaired output signal is available on the screw terminal connector on the rear of the DCM. The output signal is similar to levels that are output from a standard CD player .
26 Surround insert connections are provided for connection to a Dolby Surround Processor . The surround insert connections are made using the TO SURROUND EX DECODER connection. Connect a cable between this connector and an external processor such as the Dolby SA-10.
27 Connect a PC computer to the RS-232 connector , turn on the DCM unit, load the DCM Manager software and either load a full configuration file (if this theater uses the exact same settings as another theater), or select and enter all of the new data.
28 INST ALLA TION- System Calibration 3. Monitoring - audio mix adjustments The DCM Manager software allows balancing of the high/low or high/mid/low signals being fed to the front panel monitor speaker . Input pink noise into all of the DCM input channels and select individual channels using the DCM front panel buttons.
29 TROUBLESHOOTING If the DCM Manager program is unable to communicate with the DCM hardware... • V erify the RS-232 cable connections. Re-seat each cable-end and finger-tighten connector retaining screws. • Make sure the 9-pin serial data cable (RS-232 cable) is a normal type cable.
30 TROUBLESHOOTING If no sound in the theater ... If one audio channel is missing ... - If PROC inputs are active, then monitor the AMPS outputs (next step). - If PROC inputs are not active, check the cable between the DCM and the Cinema Processor or the Cinema Processor itself.
31 • V erify that the DCM Input Clip LED is not lit. If it is, the cinema processor output signal needs to be turned down. TROUBLESHOOTING If theater audio is distorted ... If switching the BYP ASS to EMERGENCY does not restore sound to the center channel.
32 SPECIFICA TIONS DCM Inputs, Screen Channels and Subwoofer Input Stage T ype Active balanced Input Impedance 20k ohms Maximum Input Level +14.2 dBu (4.
33 SPECIFICA TIONS Hearing Impaired Output Output Stage T ype Single-ended balanced impedance Output Impedance 50 ohms Nominal Output Level -11.8 dBu (200 mVrms) Loading Requirements R min = 2k ohms, C max = 4 nanoFarads Monitor Speaker Driver 4.
34 Disclaimer QSC Audio Products, Inc. is not liable for any damage to speakers, amplifiers, or any other equipment that is caused by negligence or improper installation and/or use of this cinema product.
35 This page intentionally left blank..
36 QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office.
デバイスDCM Speakers DCM-2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
DCM Speakers DCM-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDCM Speakers DCM-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DCM Speakers DCM-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DCM Speakers DCM-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DCM Speakers DCM-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDCM Speakers DCM-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DCM Speakers DCM-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDCM Speakers DCM-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。