Dellメーカー435MTの使用説明書/サービス説明書
ページ先へ移動 of 40
DellStudioXPS™435MTServiceManual Model DCMMF Notes, Cautions, and Warnings Information in this document is subject to change without notice. © 2008DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Replacing the Badge Back Light DellStudioXPS™435T/9000ServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Remove the front panel (see Replacing the Front Panel ).
Back to Contents Page Before You Begin DellStudioXPS™435MTServiceManual Technical Specifications Recommended Tools Turning Off Your Computer Safety Instructions This chapter provides procedures for removing and installing the components in your computer.
3. Disconnect all telephone or network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets. 5. Press and hold the power button while the system is unplugged to ground the system board.
Back to Contents Page Replacing a PCI Express Card DellStudioXPS™435MTServiceManual Removing a PCI Express Card Installing a PCI Express Card Replacing the Card Retention Bracket Configuring Your Computer After Removing or Installing a PCI Express Card Removing a PCI Express Card 1.
9. Install a filler bracket in the empty card - slot opening. 10. Replace the card retention bracket (see Replacing the Card Retention Bracket ). 11. Replace the computer cover (see Replacing the Computer Cover ). 12. Connect the computer and devices to electrical outlets, and then turn them on.
12. Connect the computer and devices to electrical outlets, and then turn them on. 13. To complete the installation, see Configuring Your Computer After Removing or Installing a PCI Express Card .
Back to Contents Page Replacing the Battery DellStudioXPS™435MTServiceManual 1. Record all the screens in system setup (see System Setup ) so that you can restore the correct settings in step 10 . 2. Follow the procedures in Before You Begin .
Back to Contents Page Replacing the Computer Cover DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin . 2. Lay your computer on its side with the computer cover facing up. 3. Open the padlock, if applicable.
Back to Contents Page Replacing the Processor DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin .
9. If the release lever on the socket is not fully extended, move it to that position. 10. Orient the front and back alignment - notches on the processor with the front and back alignment - notches on the socket. 11. Align the pin - 1 corners of the processor and socket.
Back to Contents Page .
Back to Contents Page Replacing Drives DellStudioXPS™435MTServiceManual Replacing a Hard Drive Replacing an Optical Drive Replacing the FlexDock Rem.
8. Align the four screw holes on the hard drive with the screw holes on the hard drive bay. 9. Replace the four screws that secure the hard drive to the chassis. 10. Connect the power and data cables to the hard drive. 11. Ensure that all the cables are properly connected and firmly seated.
13. Replace the computer cover (see Replacing the Computer Cover ). 14. Connect your computer and devices to their electrical outlets, and turn them on. Replacing the FlexDock 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ).
14. Replace the computer cover (see Replacing the Computer Cover ). 15. Connect your computer and devices to electrical outlets, and then turn them on.
Back to Contents Page CAUTION: To comply with FCC regulations, it is recommended that you replace the drive panel insert whenever the FlexDock or optical drive is removed from the computer.
Back to Contents Page Replacing Fans DellStudioXPS™435MTServiceManual Replacing the Chassis Fan Replacing the Processor Fan and Heat Sink Assembly Replacing the Chassis Fan 1. Follow the procedures in Before You Begin .
4. Carefully move away any cables that are routed over the processor fan and heat sink assembly. 5. Loosen the four captive screws securing the processor fan and heat sink assembly. 6. Lift the processor fan and heat sink assembly out of the computer, and set it aside.
Back to Contents Page Replacing the Front Panel DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Grasp and lift the front panel grips one at a time to release it from the front of the computer.
Back to Contents Page Replacing the Front I/O Panel DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Remove the front panel (see Replacing the Front Panel ).
.
Back to Contents Page Replacing Memory Module(s) DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Locate the memory modules on the system board (see System Board Components ).
8. Insert the module into the connector until the module snaps into position. If you insert the module correctly, the securing clips snap into the cutouts at each end of the module. 9. Replace the computer cover (see Replacing the Computer Cover ).
Back to Contents Page Replacing the Power Supply DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Follow the DC power cables that stem from the power supply and disconnect each connected power cable.
Back to Contents Page .
Back to Contents Page Replacing the Rubber Foot DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin .
Back to Contents Page Replacing the System Board DellStudioXPS™435MTServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Remove any expansion cards on the system board (see Replacing a PCI Express Card ).
10. Replace the eight screws that secure the system board to the chassis. 11. Connect the cables that you removed from the system board. 12. Replace the memory modules (see Replacing Memory Module(s) ). 13. Replace the processor (see Replacing the Processor ).
Back to Contents Page System Setup DellStudioXPS™435MTServiceManual Overview Clearing Forgotten Passwords Clearing CMOS Settings Flashing the BIOS .
Processor Cache L3 Displays the processor L3 cache size. Memory Installed Indicates the amount of installed memory in MB. Memory Available Indicates the amount of memory available in MB. Memory Speed Indicates the memory speed in MHz. Memory Technology Indicates the memory technology; DDR3.
Boot Sequence This feature allows you to change the boot sequence for devices. Boot Options l Hard Drive — The computer attempts to boot from the primary hard drive. If no operating system is on the drive, the computer generates an error message.
Clearing Forgotten Passwords 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Locate the 3 - pin password connector (PSWD) on the system board (see System Board Components ).
4. Remove the 2 - pin jumper plug from pins 2 and 3 and fix it on 1 and 2. 5. Wait for approximately five seconds to clear the CMOS setting. 6. Remove the 2 - pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3. 7. Replace the computer cover (see Replacing the Computer Cover ).
Back to Contents Page Technical Overview DellStudioXPS™435MTServiceManual Inside View of Your Computer System Board Components Inside View of Your Computer System Board Components WARNING: Before working inside your computer, read the safety information that shipped with your computer.
Back to Contents Page (DIMM_5) (DIMM_2) 7 memory module connector (DIMM_6) 8 memory module connector (DIMM_3) 9 main power connector (PWR1) 10 password jumper (PSWD) 11 serial ATA drive connector .
Back to Contents Page DellStudioXPS™435T/9000ServiceManual Information in this document is subject to change without notice. © 2009DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Replacing the Top Cover DellStudioXPS™435T/9000ServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Remove the front panel (see Replacing the Front Panel ).
8. Remove the I/O panel (see Replacing the I/O Panel ). 9. Set the computer top cover aside in a secure location. 10. To replace the top cover, perform the removal procedure in reverse order.
Back to Contents Page Replacing the I/O Panel DellStudioXPS™435T/9000ServiceManual 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Replacing the Computer Cover ). 3. Remove the front panel (see Replacing the Front Panel ).
デバイスDell 435MTの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dell 435MTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell 435MTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell 435MTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell 435MTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell 435MTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell 435MTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell 435MTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell 435MTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。