DellメーカーE6230の使用説明書/サービス説明書
ページ先へ移動 of 81
Dell Latitude E6230 Owner's Manual Regulatory Model: P14T Regulatory Type: P14T001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer....................................................................................................... 7 Before Working Inside Your Computer ..........................................................................
Installing the Hall Sensor ........................................................................................................................................ 35 Removing the Coin-Cell Battery .....................................................
7 Technical Specifications......................................................................................................... 75 8 Contacting Dell...................................................................................................
6.
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
6. Close the display and turn the computer upside-down on a flat work surface. NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9.
After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer.
10.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the Secure Digital (SD) Card 1.
Removing The ExpressCard 1. Follow the procedures in Before Working Inside Your Computer . 2. Press in on the ExpressCard to release it from the computer. 3. Slide the ExpressCard out of the computer. Installing the ExpressCard 1. Slide the ExpressCard into its slot until it clicks into place.
3. Remove the battery from the computer. Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working Inside Your Computer .
3. Loosen the captive screw that secures the base cover to the computer. 4. Slide the base cover out of the computer. Installing the Base Cover 1. Place the base cover to align with the screw hole correctly on the computer. 2. Tighten the screw to secure the base cover to the computer.
3. Disconnect and unroute the bluetooth cable. 4. Remove the screw that secures the bluetooth module to the computer. 5. Remove the bluetooth module. 15.
Installing the Bluetooth Module 1. Connect the bluetooth cable to its connector. 2. Tighten the screw to secure the bluetooth module to the computer. 3. Install the: a) base cover b) battery c) ExpressCard d) SD card 4. Follow the procedures in After Working Inside Your Computer .
5. Use a flat-headed screw driver to lift up the edge of the hard drive. 6. Remove the hard drive. 7. Remove the hard-drive connector from the hard drive.
8. Remove the hard-drive caddy from the hard drive. Installing the Hard Drive 1. Attach the hard-drive caddy to the hard drive. 2. Connect the hard-drive connector. 3. Replace the hard drive in its slot. 4. Replace the hard-drive bracket to secure the hard drive.
4. Lift and remove the memory module from its connector. 5. Repeat steps 2 and 3 to remove the second memory module. Installing the Memory 1. Insert the memory module into the socket. 2. Press the retention clips to secure the memory module to the system board.
4. Disconnect the Smart Card reader cable. 5. Disconnect the touchpad cable. 6. Remove the screws that secures the palmrest to the computer. 20.
7. Flip the base of the computer to a 45–degree angle. 8. Press downward on the palmrest from the base of the computer. 9. Remove the palmrest. 21.
Installing the Palmrest 1. Align the palmrest to its slot. 2. Press along the sides of the palmrest until it snaps in place. 3. Flip the computer and tighten the screws that secures the palmrest in place. 4. Connect the following cables: a) touchpad b) Smart Card reader c) SD card reader 5.
4. Flip the computer and remove the screws that secure the keyboard. 5. Flip the keyboard over. 6. Disconnect the keyboard data cable. 23.
7. Remove the keyboard. 8. Peel off the mylar tape. 9. Disconnect the keyboard cable. 24.
Installing the Keyboard 1. Connect the keyboard cable. 2. Affix the mylar tape to the keyboard. 3. Connect the keyboard data cable. 4. Slide the keyboard into its compartment and ensure that it snaps into place. 5. Tighten the screws to secure the keyboard.
4. Remove the screw that secures the WLAN card to the computer. 5. Slide and remove the WLAN card out from its slot on the system board. Installing the Wireless Local Access Network (WLAN) 1. Insert the WLAN card into its connector at a 45–degree angle into its slot.
Removing the Heat-Sink Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD Card b) ExpressCard c) battery d) base cover 3. Disconnect the heat-sink fan cable. 4. Remove the screws that secure the heat-sink fan to the computer.
5. Lift and remove the heat-sink fan. Installing the Heat-Sink Fan 1. Replace the heat-sink fan in its slot. 2. Tighten the screws that secure the heat-sink fan to the computer. 3. Connect the heat-sink fan cable. 4. Install the: a) base cover b) battery c) ExpressCard d) SD card 5.
3. Loosen the screws that secure the heat-sink module to the computer. 4. Remove the heat-sink module. Installing the Heat-Sink module 1. Replace the heat-sink module in its slot. 2. Tighten the screws to secure the heat-sink module. 3. Install the: a) heat-sink fan b) base cover c) battery d) ExpressCard e) SD Card 4.
Removing the Speakers 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD Card b) ExpressCard c) battery d) base cover 3.
5. Remove the screws that secure the speaker to the computer. 6. Remove the screws that secure the other speaker to the computer. 7. Remove the speakers.
Installing the Speakers 1. Align the speakers in the original position and connect the speaker cables. 2. Tighten the screws to secure both the speakers 3. Install the: a) base cover b) battery c) ExpressCard d) SD card 4. Follow the procedures in After Working Inside Your Computer .
4. Disconnect the hall sensor cable. 5. Remove the screws that secure the chassis base. 6. Pull up the chassis base. 33.
Installing the Chassis Base 1. Align the chassis base to the computer. 2. Tighten the screws to secure the chassis base to the computer. 3. Connect the following cables: a) hall sensor b) touchpad 4. Install the: a) speakers b) heat-sink fan c) bluetooth module d) keyboard e) palmrest f) base cover g) battery h) ExpressCard i) SD card 5.
4. Remove the screw that secures the hall sensor. 5. Remove the hall sensor. Installing the Hall Sensor 1. Replace the hall sensor in its slot. 2. Tighten the screw to secure the hall sensor.
Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD Card b) ExpressCard c) battery d) cover e) palmrest f) keyboard g) bluetooth module h) heat-sink fan i) speakers j) base chassis 3. Disconnect the coin-cell battery cable.
3. Install the: a) base chassis b) speakers c) bluetooth module d) heat-sink fan e) keyboard f) palmrest g) base cover h) battery i) ExpressCard j) SD card 4. Follow the procedures in After Working Inside Your Computer . Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer .
4. Disconnect the ExpressCard cage cable. 5. Disconnect the power-connector cable. 6. Remove the screws that secure the system board to the computer. 38.
7. Lift the left edge of the system board and raise it to a 45-degree angle. 8. Remove the system board. Installing the System Board 1. Place the system board in its compartment.
4. Install the: a) chassis base b) display assembly c) speakers d) heat-sink fan e) heat sink f) bluetooth module g) keyboard h) palmrest i) base cover j) battery k) ExpressCard l) SD card 5. Follow the procedures in After Working Inside Your Computer .
4. Remove the power connector port. Installing the Power-Connector Port 1. Insert the power-connector port in its slot. 2. Connect the power connector to the system board. 3. Install the: a) base chassis b) speakers c) heat-sink module d) heat-sink fan e) bluetooth module f) keyboard g) palmrest h) base cover i) battery j) ExpressCard k) SD card 4.
3. Disconnect the ExpressCard reader cable. 4. Remove the screws that secure the ExpressCard cage to the computer. 5. Remove the ExpressCard cage. 42.
Installing the ExpressCard Cage 1. Insert the ExpressCard cage into its compartment. 2. Tighten the screws to secure the ExpressCard cage to the computer 3. Connect the ExpressCard reader cable. 4. Install the: a) base chassis b) speakers c) heatsink d) bluetooth module e) keyboard f) palmrest g) base cover h) battery i) ExpressCard j) SD card 5.
4. Remove the screw that secures the WiFi-switch board to the computer. 5. Remove the WiFi-switch board. Installing the WiFi-Switch Board 1. Place the WiFi-switch board in its compartment. 2. Tighten the screw to secures the WiFi-switch board to the computer.
Removing the Smart Card Cage 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD card b) ExpressCard c) battery d) base cover e) palmrest f) keyboard g) heat-sink fan h) bluetooth module i) speakers j) display assembly k) lower chassis l) system board 3.
Installing the Smart Card Cage 1. Place the smart card cage in its compartment. 2. Tighten the screw that secures the smart card cage to the computer. 3. Install the: a) system board b) base chassis c) display assembly d) speakers e) bluetooth module f) heat-sink fan g) keyboard h) palmrest i) base cover j) battery k) ExpressCard l) SD card 4.
4. Work your way along to the sides and bottom edge of the display bezel. 5. Remove the display bezel from the display assembly. Installing the Display Bezel 1. Place the display bezel onto the display assembly. 2. Starting from the top corner, press on the display bezel and work around the entire bezel until is snaps onto the display assembly.
3. Remove the screws that secure the display panel to the display assembly. 4. Flip the display panel over. 5. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel.
6. Remove the display panel from the display assembly. Installing the Display Panel 1. Affix the LVDS cable connector tape and connect the LVDS cable to the display panel. 2. Place the display panel onto the display assembly. 3. Tighten the screws that secure the display panel to the display assembly.
3. Remove the screws from the bottom of the chassis 4. Disconnect any antenna cables that may be connected to the wireless solutions and remove them from the routing channels. 5. Remove the screws that secure the low-voltage differential signaling (LVDS) bracket to the computer.
6. Remove the LVDS bracket. 7. Disconnect the LVDS cable. 8. Pull the antenna cables through the opening on top of the computer. 51.
9. Remove the screws that secure the display assembly to the computer. 10. Pull up the display assembly from the chassis. Installing the Display Assembly 1. Place the display assembly on the computer. 2. Tighten the screws to secure the display assembly to the computer.
11. Follow the procedures in After Working Inside Your Computer . Removing the Camera 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) battery b) display bezel 3. Peel away the conductive tape. 4. Remove the screw that secures the camera to the display assembly.
5. Lift up the right edge of the camera. 6. Flip the camera outwards. 7. Disconnect the camera cable and remove the camera. Installing the Camera 1. Install the camera in its slot on the display panel. 2. Tighten the screw to secure the camera to the display assembly.
5. Install the: a) display bezel b) battery 6. Follow the procedures in After Working Inside Your Computer . Removing the LVDS and Camera Cable 1. Follow the procedures in Before Working Inside Your Computer .
4. Peel back the adhesives that secures the LVDS and camera cable to the display assembly. 5. Remove the LVDS and camera cable from the display assembly. Installing the LVDS and Camera Cable 1. Affix the LVDS and camera cable to the display assembly. 2.
3 Additional Information This section provides information for the additional features that are part of your computer. Docking Port Information The docking port is used for connecting the laptop to a docking station (optional).
58.
4 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only.
Option Description • Enabled • Enabled w/PXE (Default Setting) Parallel Port Allows you to define and set how the parallel port on the docking station operates. You can set the parallel port to: • Disabled • AT • PS2 • ECP Serial Port Identifies and defines the serial port settings.
Option Description • Enable SMART Reporting — This option is disabled by default. USB Configuration Allows you to define the USB configuration. The options are: • Enable Boot Support • Enable External USB Port Default Setting: both the options are enabled.
Table 4. Video Option Description LCD Brightness Allows you to set the panel brightness when the ambient sensor is Off. Optimus Allows you to enable or disable the NVIDIA Optimus technology. • Enable Optimus — Default Setting. Table 5. Security Option Description Intel TXT (LT-SX) Configuration This option is disabled by default.
Option Description Default Setting: Enable CPU XD Support Computrace Allows you to activate or disable the optional Computrace software The options are: • Deactivate (Default Setting) • Disable .
Option Description Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor. Default Setting: Enabled Table 7. Power Management Option Description AC Behavior Allows the computer to power on automatically, when AC adapter is plugged.
Option Description • Custom Charge — you can set the percentage to which the battery must charge. NOTE: All charging modes may not be available for all the batteries. Battery Slice Configuration Allows you to define the how to charge the battery. The options are: • Standard Charge • Express Charge (Default Setting) Table 8.
Table 9. Virtualization Support Option Description Virtualization Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization Technology. • Enable Intel Virtualization Technology - Default Setting.
Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensure that your computer battery is fully charged and connected to a power outlet 1. Re-start the computer.
NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to log on to the computer. To enter a system setup, press <F2> immediately after a power-on or re-boot.
70.
5 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
72.
6 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Device Status Lights Table 13. Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode.
Battery Status Lights If the computer is connected to an electrical outlet, the battery light operates as follows: Alternately blinking amber light and white light An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop.
7 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For comprehensive specification of your computer go to Specifications’ section in your Owner’s Manual available on the support site at dell.
Audio Internal high-definition audio External microphone-in/stereo headphones/external speakers connector Speakers two Internal speaker amplifier 1 W (RMS) per channel Volume controls keyboard functio.
Display Latitude E6330 13.3" Dimensions: Latitude E6230 Height 300.90 mm (11.84 inches) Width 180.00 mm (7.08 inches) Diagonal 317.30 mm (12.49 inches) Active area (X/Y) 276.61mm x 155.52 mm Latitude E6330 Height 314.10 mm (12.36 inches) Width 188.
Battery • 6-cell (58 WHr) Lithium-ion battery Dimensions: 3-cell Depth 29.97 mm (1.18 inches) Height 19.80 mm (0.78 inch) Width 208.00 mm (8.19 inches) 6-cell Depth 54.10 mm (2.13 inches) Height 20.85 mm (0.82 inch) Width 214.00 mm (8.43 inches) Weight: 3-cell 172.
Physical Latitude E6230 Latitude E6330 Height 22.40 mm to 24.70 mm (0.88 inch to 0.97 inch) 25.40 mm to 30.10 mm (1 inch to 1.19 inches) Width 309.00 mm (12.16 inches) 335.00 mm (13.19 inches) Depth 226.00 mm (8.89 inches) 223.30 mm (8.79 inches) Weight 1.
80.
8 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
デバイスDell E6230の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dell E6230をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell E6230の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell E6230の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell E6230で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell E6230を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell E6230の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell E6230に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell E6230デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。